Temperature Sensor Thru-Hull Replaces EP-80 Pre-configured as Water Temperature Can be reconfigured* to output the following temperature types: Outside Inside Engine Room Cabin Live Well Bait Well Refrigeration Heating System *can only be controlled/configured on Navico MFDs

DX900+ Multilog Smart™ Electromagnetic Speed Sensor Thru‑Hull NMEA 0183 Say goodbye to the paddlewheel and hello to Smart® Sensor technology. The DX900+ uses electromagnetic technology to accurately measure dual-axis speed through water plus immediately calculate leeway travel. Paddlewheels need cleaning and only measure speed longitudinally. The DX900+ measures water flow at 360° and will immediately deliver the leeway data to your instrument. There are no moving parts to clean or maintain. Performance sailors, racers, or long-distance cruisers will immediately see the benefits of the accuracy and reliability of the DX900+. The DX900+ is available as a Speed and Water-temperature sensor. Features: Electromagnetic dual-axis speed, and water temperature with no moving parts Measures transverse and longitudinal speed that instantaneously calculates leeway angle and speed through water with no latency Connects and shares data wirelessly with AIRMAR’s CAST™ app. Perfect for displaying performance data on phones or tablets, plus makes calibration fast and easy. Outputs heel and trim The sensing pins in contact with the water are made from very high-quality alloy, allowing very stable measurements and high resistance to corrosion. (Do not use any bottom paint on exposed sensing pins.) Thru-hull, low-profile housing with water valve Retractable insert for safe storage Available in a plastic (P717V) or stainless steel (SS617V) housing Retrofits to existing P617V housing Specifications: Weight (sensor, box, and cable): Plastic—1 kg (2.3 lb.) Stainless steel—2 kg (4.4 lb.) Hull Material: Plastic housing for fiberglass or metal hull/Stainless steel housing compatible with all hull materials Deadrise Angle: Up to 22° Hole Diameter: Fiberglass or wood—51 mm or 2", Stainless steel housing in metal hull—57 mm or 2-1/4" Transverse Speed Range: ±6 knots Longitudinal Speed Range: ±60 knots Accuracy of Transverse and Longitudinal Speed: ±0.1 knots for speeds under 10 knots, ±1% for speeds above 10 knots Display Resolution: 0.01 knots Outputs: NMEA 0183—speed and temperature Configurable Data Update Rate: Up to 10 Hz Operating Temperature Range: -15°C to 55°C (5°F to 131°F) Water Temperature Accuracy: +0.5°C (+1.0°F) Power: Supply Voltage: 9 to 16 VDC Average Power Consumption: NMEA 0183 - 2.5 W Standard Cable Length: NMEA 0183 - 6M (20') Includes: Blanking plug CE Compliant: Yes to IEC60945 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B285M Medium-Frequency CHIRP Transducer with Temperature - Bronze Thru-Hull with High Speed Fairing Block Features: Frequency: Chirp 85 - 135 kHz Power Rating: 1 KW Connector: 10 Pin Fairing Block: High Speed Fairing Block Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

xSonic B150M Thru-Hull Transducer - 9-Pin 10M Cable - 0° As CHIRP continues to redefine recreational fishing, AIRMAR has expanded the lineup of broadband transducers to satisfy the growing demand for this game changing technology. The B150M economical CHIRP transducers designed for offshore fishing and freshwater anglers. Operating at a frequency range of 95-155 kHz, these transducers reveal fish in shallow, murky waters at medium depths (up to 2,500 feet*) along with ultra-clear target resolution.  *Depths vary depending on target strength and sea conditions  A tilted element model in the CHIRP Thru-Hull product line, the B150M CHIRPS across the following bandwidth: M Model - Medium Frequency 95-155 kHz    Features: Depth and water temperature sensor 300W Bronze Thru Hull 0° tilt Ideal for inshore or coastal fishing in shallow to medium depths Freshwater anglers will see fish holding close to structures and suspended fish  Track bottom at higher boat speeds More coverage under your boat delivers wider archesand 26° to 17° beamwidths  Cover the medium frequency range-CHIRPs from 95-155kHz to provide 60 kHz of total bandwidth from one transducer Hull Type: Fiberglass, wood 1 internal ceramic

StructureScan 3D Thru-Hull Transducer Fairing Block Only Navico's high-performance fairing block gives you greater StructureScan performance at speed.

B260 Bronze Thru Hull The B260 will enhance fish detection on virtually all of today's fish finders. High-performance has been redefined with its Broadband Ceramic Technology. The narrow, 6 degree beam 200 kHz ceramic will give you excellent resolution and crisp image detail needed for bottom fishing. The B260's low ringing is perfect for finding fish holding tight to the bottom and other structure. The seven-element 50 kHz array has a wider 19 degree beam for deeper blue-water fishing. The outcome at both frequencies is excellent resolution and crisp image detail where it's needed most. Compatible with Lowrance HDS Series and Simrad NSE Series Multifunction Display Units. Features Depth/Temp 50/200 kHz 1 kW RMS High-performance Bronze Thru Hull 7 pin blue connector Includes High Speed Fairing Block

StructureScan 3D® Thru-Hull Transducer with Medium/High CHIRP StructureScan 3D thru-hull transducer with Medium and High CHIRP. Single transducer for flat to hull mounting or fits deadrises up to 5 degrees with fairing block. StructureScan 3D connectors connect to a StructureScan 3D module, CHIRP connector includes XID in the 9 pin connector and connects directly to the MFD.

StructureScan 3D Thru Hull with L/H Chirp and StructureScan 3D StructureScan 3D thru hull transducer with Low and High CHIRP. Single transducer for flat to hull mounting or fits deadrises up to 5 degrees with fairing block. StructureScan 3D connectors connect to a StructureScan 3D module, CHIRP connector includes XID in the 9 pin connector and connects directly to the MFD.

GT21-TH Perfect for coastal and offshore fishermen who want traditional sonar and CHIRP ClearVü scanning sonar with a stainless steel stem, this thru-hull mount transducer consistently displays clear and crisp fish arches with superior target separation as well as clear definition of structure below the boat. The CHIRP ClearVü element has a power rating of 500 W and operating frequencies of 260/455 kHz. The traditional sonar has a power rating of 600 W and operating frequencies of 50/200 kHz. It includes a built-in fast-response temperature sensor. For hull deadrises less than 25 degrees.  GT21-TH includes an 8-pin transducer with stainless steel stem, fairing block, isolation plate and bushings, mounting hardware and installation instructions. Follow the instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Thru-Hull Fittings

Shoot Thru-Hull Pod with Remote Temp - 9-Pin Navico 9-Pin 83/200 kHz shoot-thru or trolling-motor mount Skimmer® with remote temp sensor with blue connector.

SS75 High Chirp 12 Degree Bronze Thru-Hull xSonic Transducer Airmar’s low-profile, Chirp-ready transducer models are the perfect addition to smaller boats, such as center consoles. The high-frequency band has a narrow beamwidth, excellent for pinpointing fish holding tight to wrecks, reefs, and other structures. High frequency also shows amazing target separation on baitfish and schooling gamefish. The SS75H transducer, operating at 130 to 210 kHz, delivers up to 80 kHz of total bandwidth in just one installation for outstanding bottom detail and fish-target resolution. This Tilted Element™ transducer has the element fixed at a 12-degree angle within the housing. Because the transducer is installed almost flush with the hull, the tilt corrects for the hull deadrise. It orients the ceramic element horizontally to ensure maximum echo returns to the transducer. Features: Depth and fast-response water-temperature sensing 600 W of power with a maximum depth of 214 m (700') High frequency (130 to 210 kHz) 15- 9 degree beamwidth High frequency delivers great shallow-water performance, bottom detail, and clear fish-target returns Low-profile, thru-hull housing provides good display resolution at speed when installed properly Recommended for stepped, planning, or displacement hull Stainless steel housing for use in all hull materials Patented Xducer ID® technology Specifications: Brand: Airmar Technology Acoustic Window: Urethane Cable-Length: 10 m (33') Common Use: Fishing, Commercial Fishing Connector: Simrad 9-Pin, Lowrance 9-Pin, Navico 9-Pin Country of Origin: USA Cross Reference: 000-13912-001 Deadrise Range: 8-15 degrees Display Connector: 9N Frequency Band: High Functions: Depth, Temperature High Frequency: 130-210 kHz High Frequency Beamwidth: 15-9 degrees Hole Size: Fiberglass or wood hull—70 mm or 2-13/16", Metal hull—79 mm or 3-1/8" Hull Material: Compatible w/ all hull materials Material: Stainless Steel Max Deadrise: Up to 24 degrees Max Deadrise Angle: 24 degrees Max Depth: 214 m (700') Max Vessel LOA: Up to 8 m (26') Mix and Match Series: 12-Pin Chirp Mounting Style: Tilted Element Thru-Hull Power Rating: 600 W Retractable housing: No Sensor Connector: MMC Single or Dual Frequency: CHIRP-Ready Single-Band Tilt Angle: 12 degrees Tilted Element: Yes Weight: 1.4 kg (3 lbs.) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Navico StructureScan™HD Sonar Stainless Steel Thru-Hull Transducer (Single) LSS-2 Though Hull Transducers Thru-hull, Stainless Steel LSS-2 StructureScan® HD transducers deliver extreme target detail, bottom discrimination and bait and game fish separation at depths to 300'/92M and a wider range of 600'/183M side-to-side coverage. All StructureScan® HD transducers are packed with an enhanced dual-frequency element array that operates at 455 kHz and 800 kHz. These Stainless steel transducers from Airmar® are available only from Navico exclusively for StructureScan® HD and StructureScan® systems. These sturdy, bronze transducers are resistant to the electrical forces in the environment where it will be used. Each feature a low-profile design that minimizes drag; provide exclusive 3-channel beam, port and starboard SideScan plus DownScan Imaging™ technology; includes a high-performance fairing that will give you Structure performance at speeds up to 35 mph; and feature a 30'/9M transducer cable.

StructureScan 3D® Stainless Steel Thru-Hull Transducer - Pair The Dual thru-hull StuctureScan 3D® Stainless Steel transducer for the StructureScan 3D® Sonar Imaging product line, providing more range and greater resolution. These transducers are designed for boats with steep or variable deadrise hull angles, for seamless display of SideScan and DownScan and 3D Imaging. As with transom-mount StructureScan 3D® transducer, the Dual thru-hull Stainless Steel version deliver extreme target detail, bottom discrimination, plus bait and game fish separation at depths to 300'(92M) and a wider range of 600'(183M) Left & Right of coverage. These Dual thru-hull Stainless Steel StructureScan 3D® transducers from Airmar® are available only from Navico exclusively for StructureScan 3D® systems. These sturdy, Dual thru-hull Stainless Steel StructureScan 3D® transducers are resistant to the electrical forces in the environment where it will be used. Each feature a low-profile design that minimizes drag; provide exclusive 3-channel beam, port and starboard SideScan, DownScan Imaging™ and 3D Imaging technology; an optional high-performance fairing is avaliable (000-13581-001) give you greater StructureScan performance at speed; and feature a 30'(9M) transducer cable. **Note if you require a longer cable you will need 2 each 000-12752-001 transducer extension cable**

StructureScan 3D® Stainless Steel Thru-Hull Transducer - Single Lowrance and Simrad Yachting announce the release of new thru-hull StuctureScan 3D® Stainless Steel transducer for the StructureScan 3D® Sonar Imaging product line, providing more range and greater resolution. As with transom-mount StructureScan 3D® transducers, the thru-hull Stainless Steel version deliver extreme target detail, bottom discrimination plus bait and game fish separation at depths to 300'(92M) and a wider range of 600'(183M) Left & Right coverage. These Stainless Steel StructureScan 3D® transducers from Airmar® are available only from Navico exclusively for StructureScan 3D® systems. These sturdy, Stainless Steel StructureScan 3D® transducers are resistant to the electrical forces in the environment where it will be used. Each feature a low-profile design that minimizes drag; provide exclusive 3-channel beam, port and starboard SideScan plus DownScan Imaging™ & 3D Imaging technology; an optional high-performance fairing is avaliable (000-13581-001) give you greater StructureScan performance at speeds; and feature a 30'(9M) transducer cable. For boats with steep or variable deadrise hull angles, consumers must purchase the StructureScan® 3D Stainless Steel Thru-Hull Pair (000-13560-001).