|
xSonic P79 Adjustable 200/50kHz Plastic In-Hull Transducer - 9-Pin
This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap.
The 9-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise.
Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat.
*Fiberglass should be no more than 5/8" thick
*Not recommended for cored hulls
|
122.22 |
|
|
Airmar P79 Adjustable 200/50kHz Plastic In-hull Transducer (8-pin)
010-10327-20
This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap.
The 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise.
Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat.
*Fiberglass should be no more than 5/8" thick. Not recommended for cored hulls.
When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
168.41 |
|
|
xSonic M135M Medium Chirp 1 kW In-Hull Transducer - 9-Pin
The M135M’s medium frequency delivers the right combination of coverage under the boat, an extended depth range, and the ability to produce clean and accurate target and structure returns in mid- to deeper water. Medium frequency also delivers excellent shallow to mid-depth performance, bottom detail, and fish-target separation. Operating at a frequency range of 85 to 135 kHz, this transducer reveals fish at medium depths up to 457 m (1500 ft) and gives ultra-clear target resolution.
Airmar’s M135M includes a plastic mounting base that is aligned with the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. The eco-friendly coolant is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is that there are no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 11 m (36') with a solid fiberglass hull.
Features:
Depth only
1 kW of power
50 kHz of total bandwidth from one transducer
Recommended for use on planing and displacement hulls
Plastic transducer and mounting base
Covers popular fishing frequencies of 88 and 107 kHz plus everything else in the bandwidth
Also available as transom (TM185M), thru-hull low-profile (B175M), and thru-hull with fairing (B285M) mounts
Patented Xducer ID® technology
Specifications:
Medium frequency: 85 to 135 kHz
Beamwidth: 16 degrees to 11 degrees
Maximum Depth: 457 m (1500 ft.)
Weight: 4.2 kg (9.2 lb.)
Recommended Boat Length: Up to 11 m (36 ft.)
Hull Material: Solid fiberglass only
Hull Deadrise: Up to 22 degrees
Acoustic Window: Urethane
Transducer Element: One broadband ceramic assembly
Includes: Adjustable mounting base
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
809.66 |
|
|
Airmar B117 200/50kHz Bronze Thru-Hull Transducer - 6 Pin
010-10182-01
Connect our bronze, thru-hull mount transducer to your compatible device to receive depth and temperature data. This transducer has an operating frequency of 200 and 50 kHz; a beamwidth of 12 degrees at 200 kHz, 45 degrees at 50 kHz; and a 0 to 8 degree deadrise.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
278.52 |
|
|
Airmar P319 200/50kHz Plastic Thru-hull Transducer (8-pin)
010-10194-21
This plastic thru-hull mount transducer performs well at high speeds.
An excellent choice for fiberglass and metal hulls, this 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 7 degree deadrise.
Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat.
Do not use on wood hulls.
When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
161.99 |
|
|
xSonic B150M Thru-Hull Transducer - 9-Pin 10M Cable - 0°
As CHIRP continues to redefine recreational fishing, AIRMAR has expanded the lineup of broadband transducers to satisfy the growing demand for this game changing technology. The B150M economical CHIRP transducers designed for offshore fishing and freshwater anglers. Operating at a frequency range of 95-155 kHz, these transducers reveal fish in shallow, murky waters at medium depths (up to 2,500 feet*) along with ultra-clear target resolution.
*Depths vary depending on target strength and sea conditions
A tilted element model in the CHIRP Thru-Hull product line, the B150M CHIRPS across the following bandwidth: M Model - Medium Frequency 95-155 kHz
Features:
Depth and water temperature sensor
300W
Bronze Thru Hull
0° tilt
Ideal for inshore or coastal fishing in shallow to medium depths
Freshwater anglers will see fish holding close to structures and suspended fish
Track bottom at higher boat speeds
More coverage under your boat delivers wider archesand 26° to 17° beamwidths
Cover the medium frequency range-CHIRPs from 95-155kHz to provide 60 kHz of total bandwidth from one transducer
Hull Type: Fiberglass, wood
1 internal ceramic
|
368.44 |
|
|
P79 Plastic In-Hull Transducer, 600w (10-Pin)
600 Watts
50/200 kHz
45/15 degree Beam Angles
Plastic In-Hull Mount for Shoot-Through Applications
30 Foot Cable with 10-Pin Connector
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
218.18 |
|
|
GT8HW-IH In-Hull Transducer - 8-Pin
GT8HW-IH transducer is ideal for bass boats that want to install the transducer inside a fiberglass hull and not on the transom where cavitation could cause issues. It requires a flat section in the hull to be mounted and is excellent for boats traveling at high speeds that want to maintain accurate depth readings.
The 8-pin transducer features high-wide CHIRP traditional sonar (150-240 kHz) and has a power rating of 250 W. It can be used in conjunction with a GT30-TM transducer and an adapter cable so you can maintain depth at high speeds and scanning capabilities at trolling speeds.
For installation, follow the included instructions carefully to avoid damaging your boat.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
116.99 |
|
|
xSonic SS175H-W/12 Stainless Steel Thru-Hull Transducer - 12° - 9-Pin
The SS175H-W is a stainless steel, thru-hull CHIRP transducer, ideal for sportfishing and commercial vessels up to 8M (25') in size. This single-channel transducer offers High CHIRP combined with a wide beam for the best resolution and coverage in shallower depths.
Features:
130-210 kHz High CHIRP with wide 25° beam for excellent fish targets
Up to 310M (1000') range with High CHIRP
1 internal broadband ceramic
Thru-hull with stainless steel housing
Suitable for fiberglass and wood hulls
Ideal for sportfishing and commercial vessels up to 8M (25')
Recommended for use with Simrad NSSevo3 Lowrance HDS Gen3 multifunction displays
|
1458.80 |
|
|
xSonic Bronze 12° HDI Transducer Thru Hull 50/200 455/800 with 9 pin connector and 10M Cable
Bronze Hybrid Dual Imaging™ (HDI) tilted element thru hull transducer
Provides 50/200kHz traditional frequencies PLUS 455/800kHz Down Scan Imaging plus temperature
12 degree tilt
10M Cable
Beam Width: 50kHz @ 45°, 200kHz @ 11° 455kHz- Fore to aft 2.8°, Port to starboard 56°, 800kHz Fore to aft 1.6° Port to starboard 32°
|
456.37 |
|
|
xSonic Bronze 0° HDI Transducer Thru Hull 50/200 455/800 with 9 pin connector and 10M Cable
Bronze Hybrid Dual Imaging™ (HDI) tilted element thru hull transducer
Provides 50/200kHz traditional frequencies PLUS 455/800kHz Down Scan Imaging plus temperature
0 degree tilt
10M Cable
Beam Width: 50kHz @ 45°, 200kHz @ 11° 455kHz- Fore to aft 2.8°, Port to starboard 56°, 800kHz Fore to aft 1.6° Port to starboard 32°
|
456.37 |
|
|
Our P79 in-hull transducer easily adjusts to hull deadrise angles up to
22'. This ensures that the beam is vertically oriented to receive echos resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
Works with the Lowrance HDS Series and Simrad NSE Series Multifuction Display units.
Features
Depth
50/200 kHz
600 W RMS
Mid-performance
Plastic
7 Pin Blue Connector
|
174.35 |
|
|
Plastic Thru-Hull Transducer, 600w (10-Pin)
600 Watts
50/200 kHz
46/10 degree Beam Angles
Plastic Thru-Hull
8-Meter Cable with 10-Pin Connector
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
202.67 |
|
|
Navico Mix & Match Cable for Low-Frequency CHIRP Transducers - 9-Pin
Specifically for use with Airmar's Mix and Match CHIRP transducers up to 1kW (1,000W).
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
114.00 |
|
|
P79 In-Hull Transducer w/Humminbird #9 Plug - 7-Pin
Our P79 in-hull transducer easily adjusts to hull dead rise angles up to 22º. This ensures that the beam is vertically oriented to receive echoes, resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
Features:
Adjusts to hull deadrise angles from 2° to 22°
No holes to drill
Depth only
Recommended for solid fiberglass hulls
Adheres to aluminum hulls under 3.8 mm (0.16") thick
Recommended for planing-hull power boats, trailered boats, rigid inflatable boats (RIBS), and racing sailboats
No hull protrusions
Boat Size: Up to 8M (25')
Specifications:
Weight: 2.3kg (5lb)
Hull Deadrise: 0° to 22°
Acoustic Window: Layered plastic urethane
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
168.41 |
|