GT8HW-IH In-Hull Transducer - 8-Pin GT8HW-IH transducer is ideal for bass boats that want to install the transducer inside a fiberglass hull and not on the transom where cavitation could cause issues. It requires a flat section in the hull to be mounted and is excellent for boats traveling at high speeds that want to maintain accurate depth readings. The 8-pin transducer features high-wide CHIRP traditional sonar (150-240 kHz) and has a power rating of 250 W. It can be used in conjunction with a GT30-TM transducer and an adapter cable so you can maintain depth at high speeds and scanning capabilities at trolling speeds. For installation, follow the included instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Airmar P79 Adjustable 200/50kHz Plastic In-hull Transducer (8-pin) 010-10327-20 This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap. The 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise. Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat. *Fiberglass should be no more than 5/8" thick. Not recommended for cored hulls. When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B619 20° Tilt Bronze Thru-Hull Transducer - 8-Pin Minimize Your Drag The B619 model have been the standard in low-profile models for many years. Their large sensitive ceramics allow deep echosounding up to 206M (700'). These nearly flush units minimize drag as only 5mm (2/10") of the housing extends outside of the hull. The bronze B619 provides a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for moreaccurate depth readings. Applications: Cruising powerboats and sailboats Sailboats Features: Depth only or Depth and temperature Fixed 20° tilted versions for 16° to 24° hull deadrise Right angle cable exit offers low headroom and protection when transducer is stepped on Included rubber washer allows tightening of the hull nut to irregular hull surfaces Housings are ABYC H-27 compliant Optional temperature sensor Bronze housing Boat Size: Up to 9M (30') WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

xSonic P79 Adjustable 200/50kHz Plastic In-Hull Transducer - 9-Pin This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap. The 9-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise. Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat. *Fiberglass should be no more than 5/8" thick *Not recommended for cored hulls

xSonic M135M Medium Chirp 1 kW In-Hull Transducer - 9-Pin The M135M’s medium frequency delivers the right combination of coverage under the boat, an extended depth range, and the ability to produce clean and accurate target and structure returns in mid- to deeper water. Medium frequency also delivers excellent shallow to mid-depth performance, bottom detail, and fish-target separation. Operating at a frequency range of 85 to 135 kHz, this transducer reveals fish at medium depths up to 457 m (1500 ft) and gives ultra-clear target resolution. Airmar’s M135M includes a plastic mounting base that is aligned with the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. The eco-friendly coolant is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is that there are no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 11 m (36') with a solid fiberglass hull. Features: Depth only 1 kW of power 50 kHz of total bandwidth from one transducer Recommended for use on planing and displacement hulls Plastic transducer and mounting base Covers popular fishing frequencies of 88 and 107 kHz plus everything else in the bandwidth Also available as transom (TM185M), thru-hull low-profile (B175M), and thru-hull with fairing (B285M) mounts Patented Xducer ID® technology Specifications: Medium frequency: 85 to 135 kHz Beamwidth: 16 degrees to 11 degrees Maximum Depth: 457 m (1500 ft.) Weight: 4.2 kg (9.2 lb.) Recommended Boat Length: Up to 11 m (36 ft.) Hull Material: Solid fiberglass only Hull Deadrise: Up to 22 degrees Acoustic Window: Urethane Transducer Element: One broadband ceramic assembly Includes: Adjustable mounting base This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

GT15M-TM Transom Mount Transducer - 8-Pin GT15M-TM transducer is perfect for fishermen who want clear bottom definition under the boat as well as crisp, clear and wide fish arches with excellent target separation to depth up to 1,900 feet. The 8-pin transducer features mid-band CHIRP traditional sonar (85-165 kHz) and has a power rating of 600 W. It can be mounted on the transom. Follow the included installation instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

P79 Adjustable In Hull Transducer 50/200kHz with 6-Pin Features: In Hull Transducer Plastic Adjustable 6-Pin WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Kayak In-Hull Transducer Mount Garmin's versatile in-hull transducer mounting solution for kayaks allows fishermen to get out on the water with their favorite Garmin equipment. The mount fits the Garmin dual beam transducer (77/200 kHz) and GT20-TM transducer (77/200 kHz/DownVü), and is for use with compatible fishfinder and combo marine devices. It can withstand continous water submersion without releasing, all while protecting your transducer (sold separately) within the kayak. The mount - a foam pad with adhesive - comes with installation instructions. No tools are required for installation; however, follow the instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SI-TEX 492/50/200 In-Hull Transducer f/ES502 Dual Frequency 50/200 kHz Max Power: 500W Beam Angle: 42 deg. @ 50 kHz, 12 deg. @ 200 kHz Housing: Plastic Mount: In-Hull Plug: 8 pin Cable: 30' Temp: No Speed: No For SI-TEX model: ES502

GT36-TM & GT8HW-IH Transducer Bundle Perfect for the coastal and offshore fisherman who wants CHIRP traditional sonar and CHIRP ClearVü and CHIRP SideVü scanning sonar, these bundles consistently display clear and crisp fish arches with superior target separation as well as clear definition of objects, structure, and fish that pass below and to the side of the boat. These bundles include the GT36-TM transom mount transducer which offers ultimate versatility, featuring Ultra High-Definition ClearVü and SideVü scanning sonars for crystal-clear images of fish and structure, so you can spend more time catching fish. Both bundles help you maintain accurate depth readings at high speed, are intended for boats with fiberglass hulls, and include the y-cable required for installing both transducers. Features: Choose the bundle with the GT15M-IH in-hull transducer, featuring mid-band CHIRP traditional sonar, if you have a boat with a fiberglass hull and a deadrise from 0° to 25° Choose the bundle with the GT8HW-IH transducer, featuring high-wide CHIRP traditional sonar, if you have a boat with a fiberglass hull and a deadrise of 0° to 6°

Airmar P319 200/50kHz Plastic Thru-hull Transducer (8-pin) 010-10194-21 This plastic thru-hull mount transducer performs well at high speeds. An excellent choice for fiberglass and metal hulls, this 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 7 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. Do not use on wood hulls. When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SS60 0° Tilt Thru-Hull 600W, 50/200kHz Transducer - 8-Pin This stainless steel 600 W 8-pin transducer provides a vertical beam without a fairing and is excellent for fiberglass and wood hulls. It has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45/12 degrees; and 0 to 7 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. When using with a 6-pin Garmin sounder, a transducer adapter cable is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SS60 12° Tilt Thru-Hull 600W, 50/200kHz Transducer - 8-Pin his stainless steel 600 W 8-pin transducer provides a vertical beam without a fairing and is excellent for fiberglass and wood hulls. It has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45/12 degrees; and an 8 to 15 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. When using with a 6-pin Garmin sounder, a transducer adapter cable is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SS60 20° Tilt Thru-Hull 600W, 50/200kHz Transducer - 8-Pin This stainless steel 600 W 8-pin transducer provides a vertical beam without a fairing and is excellent for fiberglass and wood hulls. It has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45/12 degrees; and a 16 to 24 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. When using with a 6-pin Garmin sounder, a transducer adapter cable is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Airmar B744VL 200/50kHz Bronze Long Stem Thru-hull Transducer (8-pin) 010-10193-22 Our bronze, thru-hull mount long stem transducer provides depth, speed and temperature data. This transducer has an operating frequency of 50 or 200 kHz and mounts on a 0-28° deadrise angle. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.