Gasoline & Propane Sensor Only This sensor is a replacement for Fireboy-Xintex P systems.  Installation: The sensor should be located by the propane-powered appliance, near the floor Avoid areas where damage may take place due to cleaning, mopping, kicking, or other physical damage Harsh chemicals should not be used to clean sensors Use the appropriate #8 mounting hardware to mount the Propane Fume Sensor in the desired location The rubber gasket should be installed between the sensor and the mounting surface Connect to the extension cable using the attached quick-disconnect connectors (Sold Separately)

Propane & Gasoline Sensor with Cable - Red Plastic Housing Gasoline & propane sensor with 12" lead and 20' sensor cable. Compatible With: G-1 Gasoline Fume Detector G-2 Gasoline Fume Detector P-1 Propane Fume Detector P-2 Propane Fume Detector  *Sold as an Individual 

Propane & Gasoline Sensor with Cable - Aluminum Housing  Gasoline & propane sensor with 12" lead and 20' sensor cable. Compatible With: G-1 Gasoline Fume Detector G-2 Gasoline Fume Detector P-1 Propane Fume Detector P-2 Propane Fume Detector  *Sold as an Individual 

Fireboy - Xintex Fireboy-Xintex manufactures top-of-the-line safety devices to keep your boating experience safe. Our equipment detects fires and fatal fumes to protect your marine craft and your life. Fireboy is the world's leading manufacturer of engine compartment fire extinguishing systems.

CO Alarm 12/24V DC - Black A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD 12/24V DC model uses boat power and has permanent internal backup Lithium-metal batteries Technical Specifications: Power Usage - 4 mA Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - No *Sold as an Individual 

CO Alarm Internal Battery - Black A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD Internal battery model uses included maintenance-free lithium-metal batteries.  No wiring and reduced labor and material costs to install.   Technical Specifications: Power Usage - None Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - No *Sold as an Individual 

CO Alarm 12/24V DC - White A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD 12/24V DC model uses boat power and has permanent internal backup Lithium-metal batteries Technical Specifications: Power Usage - 4 mA Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - No *Sold as an Individual 

CO Alarm Internal Battery - White A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD Internal battery model uses included maintenance-free lithium-metal batteries.  No wiring and reduced labor and material costs to install.   Technical Specifications: Power Usage - None Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - No *Sold as an Individual 

CO Alarm 12/24V DC with Interconnect - Black   A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Interconnect up to ten (10) CO alarms - all connected CO alarms sound together  Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD 12/24V DC model uses boat power and has permanent internal backup Lithium-metal batteries Technical Specifications: Power Usage - 4 mA Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - Yes *Sold as an Individual 

CO Alarm Internal Battery w/Interconnect - Black A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Interconnect up to ten (10) CO alarms - all connected CO alarms sound together  Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD Internal battery model uses included maintenance-free lithium-metal batteries.  No wiring and reduced labor and material costs to install.   Technical Specifications: Power Usage - None Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - Yes *Sold as an Individual 

CO Alarm 12/24V DC with Interconnect - Black   A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Interconnect up to ten (10) CO alarms - all connected CO alarms sound together  Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD 12/24V DC model uses boat power and has permanent internal backup Lithium-metal batteries Technical Specifications: Power Usage - 4 mA Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - Yes *Sold as an Individual 

CO Alarm Internal Battery w/Interconnect - White A Carbon Monoxide (CO) detector should be installed in each accommodation space.  Small crafts or RV's with an open design may require only one (1) detector for adequate protection.  If two (2) or more sleeping areas or spaces are partitioned, then one (1) detector should be installed in each of the spaces. The Fireboy-Xintex CMD6-M Series CO alarm uses a sensor operating with a microprocessor to measure Carbon Monoxide (CO) levels.  Using a “Time Weighted Average” (TWA) process, it monitors CO concentration, temperature and time to calculate levels of Carboxyhemoglobin (COHb).  COHb is the degree to which the oxygen carrying capacity of the blood is impeded by the union of carbon monoxide to the hemoglobin and as expressed as a percentage.  The human body absorbs CO easier than oxygen and COHb is the ratio absorbed carbon monoxide to oxygen in bloodstream.  The CMD6-M alarm calculates the COHb as function of time and determines the appropriate alarm response. *Long sensor life – approximately 7 year end-of-life (EOL) Features: Interconnect up to ten (10) CO alarms - all connected CO alarms sound together  Microprocessor controlled Compact design for inconspicuous protection Time-weighted average CO measurement process constantly monitors all CO levels Highly resistant to most chemicals, solvents & cleaners CMD6-MD Internal battery model uses included maintenance-free lithium-metal batteries.  No wiring and reduced labor and material costs to install.   Technical Specifications: Power Usage - None Alarm Point - 10% COHb Alarm Horn - 85 dBA Dimensions - .5" x 3.5" x 1.21" (8.9 x 8.9 x 3.1 cm) Interconnect Functionality - Yes *Sold as an Individual 

MA Series Fire Extinguishing System - 450 Cubic Feet Fireboy-Xintex clean agent fire extinguisher systems are designed to automatically discharge whenever the protected space's ambient temperature reaches 175 degrees Fahrenheit. When the Fireboy System discharges, the extinguisher is designed to fully empty the HFC-227ea (Heptafluoropropane) and 3M Novec Clean Agent in less than 10 seconds.  No clean-up is required.  There is no powdery residue or water left behind.  The fire is extinguished by a combination of heat reduction and chemical reactions. *Diesel-powered craft require installation of an Engine Shutdown System  Features: Protects engine rooms and machinery spaces  Pre-engineered, total flooding system The safest way to combat an engine room fire Automatic discharge at 175°F (79°C) with optional manual release Utilizes HFC-227ea and 3M Novec clean agents – an effective Halon replacement No water or powdery residue Includes locking lever for increased safety when removing or installing cable Certifications: U.S.C.G. EN ISO 9094-1 and 9094-2 standards  ISO RINA MCA Certified Factory Mutual  Technical Specifications: Volume Protected - 450 ft3 Dimensions (Dia. x H) - 7.1" x 19.4" (18 x 49.3 cm) Agent - HFC-227ea and 3M Novec Agent Weight - 19.4 lbs (8.8 kg) System Pressure (@70°F) - 240 psi In the Box: Fire extinguisher Mounting bracket Helm station panel - 90107 Owners manual  *Sold as an Individual 

Gasoline Fume Detector - Black Bezel - 12/24V The Single Channel Gasoline Fume Detector is an effective means to monitor gasoline fumes in an engine compartment, fuel tank storage area or in other areas where gasoline fumes might accumulate.   Features: Simple Installation Audible and visual alarm to indicate LEL (Lower Explosive Level) presence  Monitors one (1) single area  Technical Specifications: Operating Temperature: -40° to 185°F (-40° to 85°C) Current Draw Nominal - 55mA  Current Draw Maximum - 95mA Operating Voltage - 9 to 30V DC Alarm Horn - 68 dB Display Style - Round with Black Bezel Display Dimensions - 2-3/16" (5.6 cm) round Cutout Dimension - 2-1/16" (5.2 cm) round hole In the Box: Fume Detector Fuel sensors x one (1) 20' Extension Cable x one (1) Instruction manual *Sold as an Individual 

Gasoline Fume Detector - Chrome Bezel - 12/24V The Single Channel Gasoline Fume Detector is an effective means to monitor gasoline fumes in an engine compartment, fuel tank storage area or in other areas where gasoline fumes might accumulate.   Features: Simple Installation Audible and visual alarm to indicate LEL (Lower Explosive Level) presence  Monitors one (1) single area  Technical Specifications: Operating Temperature: -40° to 185°F (-40° to 85°C) Current Draw Nominal - 55mA  Current Draw Maximum - 95mA Operating Voltage - 9 to 30V DC Alarm Horn - 68 dB Display Style - Round with Chrome Bezel Display Dimensions - 2-3/16" (5.6 cm) round Cutout Dimension - 2-1/16" (5.2 cm) round hole In the Box: Fume Detector Fuel sensors x one (1) 20' Extension Cable x one (1) Instruction manual *Sold as an Individual