3 Blade aluminum propeller for 40-140 horsepower outboards and 1.6L through 3.0L sterndives with 4-1/4" gear case, 13 tooth spline and thru hub exhaust.

Hustler® - Right Hand - Aluminum Propeller - LE1/LE2-1315-4 - 4-Blade - 13.5" x 15 Pitch The Prop that put the “four” in Perfourmance! Turning Point’s Four Blade Hustler revolutionized the aluminum propeller market when introduced over 6 years ago. No one had ever produced a state-of-the-art Swept Cleaver design for 40-150hp applications. These props re-wrote the rules, proving that you can run a four blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers’ propellers. These Turning Point props also produced up to 46% more reverse thrust than other comparable designs in recent tests. The Hustler 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70’s, 80’s, 90’s, and ’00’s, and will outrun most newer props, including five blade ski props. Squeeze Cast for Added Strength Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency. Long Lasting Ultracoat™ Powder Coated Finish Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance. Large Free Flowing Exhaust Ports Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat. Turning Point manufactures Hustler propellers to fit 6-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better. Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection. WARNING: This product can expose you to chemicals including CARBON BLACK which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Express® Mach4™ - Right Hand - Stainless Steel Propeller - EX1/EX2-1315-4 - 4-Blade - 13.5" x 15 Pitch The Prop that put the “four” in Perfourmance! Turning Point’s Four Blade revolutionized the propeller market when it was introduced. No one had ever produced a state-of-the-art Swept Cleaver design for 40-150hp applications. These props re-wrote the rules, proving that you can run a four blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers’ propellers. These Turning Point props also produced up to 46% more reverse thrust than other comparable designs in recent tests. Now manufactured in our Industry leading TP17 stainless, the Express Mach4 series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older stainless designs from the 70’s, 80’s, 90’s, and ’00’s, and will outrun most newer props, including five blade ski props. Proprietary Stainless Steel, TP17™ Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat. Large Free Flowing Exhaust Ports Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat. Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better. Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Express® Mach4™ - Left Hand - Stainless Steel Propeller - EX1/EX2-1315-4L - 4-Blade - 13.5" x 15 Pitch The Prop that put the “four” in Perfourmance! Turning Point’s Four Blade revolutionized the propeller market when it was introduced. No one had ever produced a state-of-the-art Swept Cleaver design for 40-150hp applications. These props re-wrote the rules, proving that you can run a four blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers’ propellers. These Turning Point props also produced up to 46% more reverse thrust than other comparable designs in recent tests. Now manufactured in our Industry leading TP17 stainless, the Express Mach4 series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older stainless designs from the 70’s, 80’s, 90’s, and ’00’s, and will outrun most newer props, including five blade ski props. Proprietary Stainless Steel, TP17™ Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat. Large Free Flowing Exhaust Ports Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat. Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better. Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

BURKS GA6-1.5MV-5-11/16, PUMP END ONLY with VITON SEAL UNSPSC Code: 40150000

HTM-4 Fender 13.5" x 34.8" - Black w/Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb In the Box: Fender Inflation Adapter  *Sold as a Kit

HTM-4 Fender 13.5" x 34.8" - Blue with Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb In the Box: Fender Inflation Adapter  *Sold as a Kit

Polyform HTM-4 Fender 13.5" x 34.8" - White with Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb In the Box: Fender Inflation Adapter  *Sold as a Kit

HTM-4 Fender 13.5" x 34.8" - Black In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb *Sold as an Individual

HTM-4 Fender 13.5" x 34.8" - Blue In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb *Sold as an Individual

HTM-4 Fender 13.5" x 34.8" - White In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb *Sold as an Individual

HTM-4 Fender 13.5" x 34.8" - Graphite In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 13.5" x 34.8" (34.3 x 88.4cm) Tube Diameter - 0.625" (1.6cm) Circumference -  42.4" (107.8cm) Volume -  15.6 gallons (59.1L) Boat Size - 40' - 50' (12.2 - 15.2M) Weight - 10.5lb *Sold as an Individual

Premium Impeller Kit 62.5 x 16 x 22.4mm - 12 Blade - Key Insert Replaces JMP 7172-01, Sherwood 09000K. Specifications: Weight: 0.119 kg Dimensions: 62.5 mm x 16 mm x 22.4 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

Premium Impeller Kit 62.5 x 16 x 32mm - 12 Blade - Key Insert Replaces JMP 7192-01, Jabsco 18838-0001, Johnson Pump 09-701B-1, Sherwood 9959K. Specifications: Weight: 0.163 kg Dimensions: 62.5 mm x 16 mm x 32 mm Type: Copolymer Neoprene Original MC Blend Certification: ISO 9001 Quality Guaranteed

4 Blade stainless propeller for 40-140 horsepower outboard and 1.6L-3.0L sterndive engines with 4-1/4" large Gearcase, 13 tooth spline and thru hub exhaust.