|
3 Blade stainless propeller for DF 150, 175, 200, 225, 250, 300 with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.
|
537.99 |
|
|
MAGNUS Escape Hatch - OD 22-3/16" x 22-3/16"
Heavy Duty Ocean Hatch
MAGNUS is a complete range of extra heavy-duty hatches. They are CE-classified AI, which means to say that they are designed for ocean use and can be fitted in any part of the hull or deck.
These hatches are provided with friction hinges, which will keep the hatch open in any position, without the need for stays. The hatch can be opened through 180° and there are virtually no obstructions in the hatch opening. Like other VETUS hatches, the MAGNUS range can be opened from inside or outside the boat. They can also be left locked; either completely watertight or in a ventilation position.
The frame profile is hand-polished and anodized. The acrylic has a thickness of 10 mm and the color is “dark smoke”.
The build-in dimensions (the cut-out sizes) of the Magnus hatches are in conformity which those that are current in the market.
Features:
External Dimensions - 22 3/16" x 22 3/16"
Cut Out Dimensions - 19 15/16" x 19 15/16"
Number of Handles - 4
*VETUS strongly advises against using MAGNUS hatches as an A1 escape hatch in the underside of a multihull. Due to the flexible nature of these types of vessels, water tightness cannot be guaranteed unless the hatch is installed on a flat and inflexible structure.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
596.88 |
|
|
ALTUS Escape Hatch - OD 23-1/16" x 23-1/16"
ALTUS is made of a sturdy aluminum profile (height 13/16” (21 mm)) with a satin sheen anodized frame and is suitable for design category A and appliance location area II. The acrylic has a thickness of 3/8” (10 mm) and is ‘dark smoke’ colored. These hatches come with adjusters which are stylish and easy to operate, allowing the lid to be held open at almost any angle up to 90º. Type ALTUS can be fitted on the deck and opened from the inside or outside. It has a ventilation position and can be locked completely watertight.
They are CE-classified AII, which means to say that they are designed for ocean use and can be fitted on deck. These hatches are provided with carefully designed hatch adjusters, which are both stylish and easy to operate.
Like other VETUS hatches, the ALTUS range can be opened from inside or outside the boat. They can also be left locked; either completely watertight or in a ventilation position.
The frame profile is hand-polished and anodized. The acrylic has a thickness of 10 mm and the color is “dark smoke”.
An aluminum counter flange and a mosquito screen are available for these hatches.
Features:
External Dimensions - 23 1/16" x 23 1/16"
Cut Out Dimensions - 19 15/16" x 19 15/16"
Number of Handles - 2
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
522.00 |
|
|
G-3 Twin Eye Fender 5.5" x 19" - Graphite
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 5.5" x 19" (14 x 48.3 cm)
Eye Diameter - 0.625" (1.6 cm)
Circumference - 17.3" 43.9 cm)
Volume - 1.4 gallons (5.3 L)
Boat Size - 15' - 20' (4.6 - 6.1 M)
Weight - 1.9 lb
*Sold as an Individual
|
18.59 |
|
|
MP Pump 28059 Stud 5/16 X 1.19
|
5.67 |
|
|
16" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 19' to 34'
Length of Tab: 16"
Width of Tab: 12"
Minimum Transom Height: 11"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
814.27 |
|
|
3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
439.99 |
|
|
3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.
|
439.99 |
|
|
3 and 4 Blade stainless propeller for Mercruiser Bravo III. 19 tooth spline and thru hub exhaust. Fits all Bravo 3 stern drives.
|
549.99 |
|
|
Stow 'n Go Low-Profile Dock Box - 40"L x 19"W x 20"H
With a UV gelcoat finish and the stainless steel lockable latch and hardware these are built tough. Our dock boxes incorporate gas shock lifts, which come standard on all models. These shocks help to keep your lid open on rocking docks and in higher wind areas and allows for a slower, more controlled closing. These fiberglass molded dock boxes are also constructed with a smooth interior finish which helps prevent splinters in your hands when storing or retrieving your boating accessories.
Features:
40"L x 19"W x 20"H
Heavy duty stainless steel lockable latch and hinges
Gas shocks come standard on all models
|
691.46 |
|
|
Premium Impeller Kit - 39.7 x 12 x 19.2mm - 6 Blade - Pin Insert
Replaces JMP 7000-01, Jabsco 22405-001, Johnson Pump 09-808B-1, Volvo Penta 875583.
Specifications:
Weight: 0.028 kg
Dimensions: 39.7 mm x 12 mm x 19.2 mm
Type: Copolymer Neoprene Original MC Blend
Certification: ISO 9001 Quality Guaranteed
|
13.92 |
|
|
Premium Impeller Kit - 39.7 x 9.5 x 19.2mm - 6 Blade - Pin Insert
Replaces JMP 7001-01, Jabsco 4528-0001, Johnson Pump 09-806B-1, Sherwood 9979K, Volvo Penta 803729, Yanmar 104211-42070.
Specifications:
Weight: 0.042 kg
Dimensions: 39.7 mm x 9.5 mm x 19.2 mm
Type: Copolymer Neoprene Original MC Blend
Certification: ISO 9001 Quality Guaranteed
|
13.73 |
|
|
Premium Impeller Kit - 39.7 x 12 x 19.2mm - 6 Blade - Single Flat Insert
Replaces JMP 7013-01, Sherwood 08000K.
Specifications:
Weight: 0.028 kg
Dimensions: 39.7 mm x 12 mm x 19.2 mm
Type: Copolymer Neoprene Original MC Blend
Certification: ISO 9001 Quality Guaranteed
|
19.08 |
|
|
3 Blade aluminum propeller for Mercruiser Bravo II stern drive engines with 19 tooth spline and thru hub exhaust.
|
419.99 |
|
|
3 and 4 Blade aluminum propeller for Volvo Penta DP280, DP290. Front propeller is 27 tooth spline. Rear Propeller is 19 tooth spline.
|
205.99 |
|