GS-2-25 Grounding Strap - 2" x 25' This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc. Features: Flexible (easily conforms to vessel contours) .01 in. (25mm) thick Specifications: Width (in./cm): 2/5.1 Length (ft./m): 25/8 Weight (lbs/kg): 3/1.4

GS-2-100 Grounding Strap - 2" x 100' This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc. Features: Flexible (easily conforms to vessel contours) .01 in. (25mm) thick Specifications: Width (in./cm): 2/5.1 Length (ft./m): 100/33 Weight (lbs/kg): 8/3.6

GS-2-50 Grounding Strap - 2" x 50' This grounding strap is an ideal conductor for RF grounding of SSB radios and other noise-sensitive transceivers, for bonding thru-hulls, etc. Features: Flexible (easily conforms to vessel contours) .01 in. (25mm) thick Specifications: Width (in./cm): 2/5.1 Length (ft./m): 50/17 Weight (lbs/kg): 5/2.3

Stainless Steel Stud 1.25" Base 10 x 24 Threads .50" Tall - 15 Quantity Studs with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

Stainless Steel Stud 1.25" Base 10 x 24 Threads 1.00" Tall - 15 Quantity Studs with smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items that require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

2000lb 2-Speed Winch - Strap Not Included Features Make light work of heavy load with Fulton brand two-speed winches.  One fast speed for quick pull-in, a seconds low speed for increased mechanical advantage. Our shift lock design allows changing gears without moving the crank handle from shaft to shaft.  Just lift the shift lock and slide the shaft into the desired gear position.  Shift lock holds the shaft in gear. Neutral, free-wheel position allows quick line pay out without spinning the handle. 5 year limited warranty Specs: Capacity (lbs.): 2,000 Handle Length: 10" Gear Ratio: 4.1:1 & 9.8:1 Strap: 20' x 2" Hub Size: 1" Hand Brake: optional Strap Included: Yes WARNING: This product can expose you to chemicals including BISPHENOL A (BPA) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Series 19 C-Track Slide - Saddle Top & Spring Loaded Stop - 71mm(2-25/32") Length Features: Spring-loaded plunger pins for fast positive positioning Chrome-plated brass slides Applications Dinghy and small catamaran jib sheet leads Adjustable hiking strap systems Specifications: Length: 71mm(2-25/32") M.W.L. 225kg(500lbs) B.L. 450kg(990lbs) Weight:70g(2.5oz)

2600lb 2-Speed Winch - Strap Not Included Winch, 2600 lbs., 2-Speed Features Make light work of heavy load with Fulton brand two-speed winches.  One fast speed for quick pull-in, a seconds low speed for increased mechanical advantage. Our shift lock design allows changing gears without moving the crank handle from shaft to shaft.  Just lift the shift lock and slide the shaft into the desired gear position.  Shift lock holds the shaft in gear. Neutral, free-wheel position allows quick line pay out without spinning the handle. 5 year limited warranty Specs: Capacity (lbs.): 2,600 Handle Length: 10" Gear Ratio: 5.1:1 & 12.2:1 Strap: 20' x 2" (Not Included) Hub Size: 1" Hand Brake: optional Strap Included: No WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Stud 1.25" Base 1/4 x 20 Threads 2.25" Tall - 10 Pieces The stainless steel stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs in shear. All studs have 1/4 x 20 threads. Use for hanging panels, through deck mounts and many other uses.

Tinned Butt Connector #2 - 25-Piece 100% Tinned Copper

Heat Shrink Ring Terminal - #8 1/2" *25-Pack Ancor heat shrink connectors offer heat-activated adhesive built into the sleeve of the heat shrink tubing. When heated, these connectors form a water-tight seal and the ultimate vibration and strain relief.

HTM-2 Fender 8.5" x 20.5" - Black with Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm) Tube Diameter - 0.625" (1.6cm) Circumference -  26.7" (67.9cm) Volume -  4.7 gallons (17.8L) Boat Size - 25' - 30' (7.6 - 9.1M) Weight - 4.7lb In the Box: Fender Inflation Adapter  *Sold as a Kit

HTM-2 Fender 8.5" x 20.5" - Blue with Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm) Tube Diameter - 0.625" (1.6cm) Circumference -  26.7" (67.9cm) Volume -  4.7 gallons (17.8L) Boat Size - 25' - 30' (7.6 - 9.1M) Weight - 4.7lb In the Box: Fender Inflation Adapter  *Sold as a Kit

HTM-2 Fender 8.5" x 20.5" - White with Adapter In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications.  Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.  The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.  Features: Even wall thickness for maximum strength and durability Molded-in ribs for strength and abrasion resistance Reinforced tube ends Designed for medium-duty use in both permanent protected and unprotected moorings Unique Polyform valve for years of service One (1) piece design Technical Specifications: Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm) Tube Diameter - 0.625" (1.6cm) Circumference -  26.7" (67.9cm) Volume -  4.7 gallons (17.8L) Boat Size - 25' - 30' (7.6 - 9.1M) Weight - 4.7lb In the Box: Fender Inflation Adapter  *Sold as a Kit

2.25" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.