Seaview SPOD Sail Pod Box Max Usable Face: 13.75" x 9" Max Cut Out Area: 12.938" x 8.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 16.938" x 12.25" Max Cut Out Area: 16" x 11.25" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview SPOD Sail Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems. Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation.  Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 13.75" x 9" Max Cut Out Area: 12.938" x 8.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview DPOD Deck Power Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply loosen the locking screw and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply tighten the locking screw, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

Seaview SPOD Sail Pod Box Max Usable Face: 11.75" x 7" Max Cut Out Area: 11" x 6.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview SPOD Sail Pod Box Max Usable Face: 4.625" x 4.625" Max Cut Out Area: 4.125" x 4.125" The Seaview Sail Pod, also known as SPOD is a instrument pod for sailboats and catamarans. Expanding on Seaviews modular mount concept, Seaview has developed a sailboat pod design with a similar concept. There are five different box sizes to fit almost any chart plotter or instrument on the market. Made from UV resistant white ABS plastic and sealed with a rubber gasket. Seaview has designed the SPOD so that the back of each box has a continuous radius that matches up with the stainless steel pod clamps. The result is precise viewing angle during installation for the customer. The pod fits the majority of steering pedestals from Jefa, Whitlock and Edson, and can be custom tailored for other systems.  Achieve the Perfect View The SPOD has a wide mounting angle, allowing for precise viewing. Angle is set during installation. Stainless Steel Clamps Two high polished stainless steel clamps are used to secure your SPOD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. the SPOD fits standard 9.5", 12" and non standard guard rails. Security screws are used to hold the SPOD together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods (part #SP1BOX). Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

Seaview DPOD Deck Power Pod Box Max Usable Face: 14.75" x 5" Max Cut Out Area: 13.875" x 4.125"  The DPOD is a instrument deck pod designed for power boats. Seaview took their modular mount concept and applied it to their instrument pod product line. There will be three different box sizes to fit almost any chart plotter or instrument on the market. What makes the DPOD so great is that it really appeals to fisherman because of its quick rotating base. Rotating Base The quick rotating base makes the DPOD a really nice choice for fisherman as it allows you to rotate the screen for better viewing on the fly, so you don't miss that catch! Simply pull the secure bolt out and rotate the DPOD left or right up to 350 degrees. To lock the anodized aluminum base back into place simply push the secure bolt back in, it's so easy you can do it with one hand! Construction The DPOD is made from UV resistant ABS plastic and security screws are used to hold it all together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this DPOD is the ability to add optional side pods (part #SP1BOX). Currently no other deck pod on the market has this feature. This optional add-on will fit single instruments 4.125" x 4.125" or smaller. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the user lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket.

SP3S1 - Uncut Rail Pod Max Useable Face: (13.75" x 9") Max Cut Out Area: (12.938" x 8.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP5S1 - Uncut Rail Pod Max Useable Face: (14.75" x 5") Max Cut Out Area: (13.875" x 4.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

SP2S1 - Uncut Rail Pod Max Useable Face: (11.75" x 7") Max Cut Out Area: (11" x 6.125") Seaview offers a solution to the age old problem of figuring out where to mount all your instruments on your sailboat. The Seaview Rail Pod allows you to mount smaller displays and instruments directly to the rail. Allowing you to postion the instrument where it is most optimal for you. Fits onto 1", 1-1/8" or 1-1/4" rails. A single high polished 316 stainless steel clamp is used. Cables are routed internally through the clamp and into the rail. The Rail Pod housing is made from UV protected ABS plastic housing, and sealed with a water tight rubber gasket. Tamper resistant screws are used to hold the housing together. A reinforced base made from King Starboard is added for increased strength and stability (on certain models). Stainless Steel Clamp A single high polished stainless steel clamp is used to secure your Rail POD onto 1", 1.125" and 1.25" (25mm to 32mm) rails. Seaview Rail Pods fit standard 9.5", 12" and non standard guard rails. Security screws are used to hold the Rail Pod together. A water tight gasket is used to prevent water from entering inside the pod, while a GORE-TEX ventilation vent lets hot air to escape without letting water in. Optional Accessory Pod One of the unique abilities with this SPOD is the ability to add optional side pods. Currently no other sailboat pod on the market has this feature. Depending on the pod box size you choose you are able to mount either one to four of these accessory pods. This gives the customer lots of flexible solutions to optimize their setup. The SP1BOX is made of UV resistant white ABS plastic and held together with tamper resistant screws and sealed with a rubber gasket. 

PODW-7-UC Compatible With: Garmin:620, 640 Raymarine: e7, e7D Seaview Power Pods are the ideal solution to mount your chart plotters, radar displays and standard navigation instruments. Say no more to having to find a level surface to mount your Power Pod. It's unique mounting design and extreme adjustability allows it to be mounted on any surface. The Power Pod has a fully adjustable 4" mounting base for better view. The Pod can tilt back, tilt forward, or side-to-side for maximum visibility. Uncut Pod box with single chartplotter 10" x 7" usable face and 2 instruments 4.72" x 4.72" usable face. Features: Accommodates nearly all brands of marine electronics Supplied uncut for your convenience White base Single chartplotter 10" x 7" usable face and 2 instruments 4.72" x 4.72" usable face Can be mounted vertical or up-side down GORE protective vent for proper ventilation Water tight gasket UV resistant ABS plastic housing Marine grade primed and powder coated aluminum base Polished stainless steel quick release handles for full horizontal & vertical adjustability

Scanpod Helm Pod System - White With great new design features, the Scanstrut Helm Pod is a perfect choice for all cockpit configurations. With options to fit radar displays, chartplotters and standard navigation instruments. Usable face : 21w x 11h  Range of Models Helm Pod – System Pod for 8" screen + 4 standard nav instruments; or 12" screen + 2 standard nav instruments Universal Helm Fixing Fits pedestal rails from 25mm to 33.7mm (0.98" - 1.33"). Using a unique clamping system, the Pod can fit rail widths from 178mm (7") upwards. Secure & Watertight Install Saddle system supports the stainless tubing enabling a secure and rigid fit onto any pedestal and also ensures a watertight seal at cable entry No Drill Fixing Kit Customised U-bolts fit around rail and through the saddles into the back of the pod eliminating the need for time consuming and awkward drilling of the stainless rail. Hassle Free Install & Service Fixings fit from back to front cutting their threads into injection moulded ABS inserts designed into the Pod front. This design allows for a quick and safe install and repeat servicing. Increased Protection Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won't deteriorate over time. Supplied Uncut As standard you will receive your Scanpod uncut. For larger orders, a factory cutting service is available.

RMX4900 Uncut (Usable Face = 12.4"W x 7.4"H) (31.5cm W x 18.8cm H) RailMount NavPods are best used for mounting of an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1" or 1.25" diameter tube. A Nickel Chrome Plated Stainless Steel arm is used to mount a NavPod. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm, and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without replacement of the pedestal guard. RailMounts are designed for all popular standard size instruments as well as 7 and 9 inch charplotters. Structural Rigidity The Gen3 enhancements now include a thicker gauge Acrylic Capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the Acrylic is combined with the durability of the ABS. The Acrylic cap protects the ABS from UV and it's potentially damaging effects on plastic. These new NavPods are really strong! Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod. This seal provides the best protection of your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal Poran Microcell Polyurathane gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome Plated Stainless Steel We use all 316 stainless steel hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. For Gen3 NavPods we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! Commitment to Quality We are committed to producing high quality Waterproof Housings for Marine Electronics. We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods. We want you to be a NavPod customer for life and are willing to earn your trust and loyalty.

NSO evo3S 16" MFD Display Only Ultimate Clarity NSO evo3S delivers the ultimate view with an ultra-bright 16-inch display, ideal for both indoor and outdoor installations. Wide viewing angles keep the screen in view from anywhere in sight, even if you’re wearing polarised sunglasses. See more than ever with Full HD resolution, and the option to combine up to six panels in a split-screen layout. Intuitive Control A responsive, multi-touch display places control of your on-board electronics at your fingertips. Intuitively navigate charts, define waypoints, and take control of connected systems such as autopilot, radar, and sonar with a touch. A range of optional keypads add classic controls, perfect for fine adjustments or use in rough conditions. Swift Response Every NSO evo3S display features an integrated six-core processor for ultimately smooth response, from charting to StructureScan® 3D imaging. Enjoy swift access to the information you need, as you need it, whether you’re cruising the open ocean or carefully navigating a crowded harbour. Glass Helm Style NSO evo3S glass helm systems offer the perfect combination of form and function. Create your own custom helm layouts to suit any activity, and switch seamlessly between those layouts in an instant. Low-profile glass helm styling complements any helm design, from ultra-modern to timeless classic. Fully Connected Built-in wireless connectivity links NSO evo3S to your existing mobile devices for remote viewing and control, and delivers easy online software upgrades via any wireless internet hotspot. Wired Ethernet, NMEA 2000®, and J1939 networking provide almost limitless integration options, from vessel-wide display systems to radar, sonar, engine integration, and much more. Features: Ultra-bright, Full HD 16-inch display Easy touchscreen control of your entire Simrad system Integrated six-core processor for ultimate performance Low-profile glass helm styling See more than ever with six-panel split screen option Connect with smartphones, tablets, and internet hotspots In The Box: Display unit Suncover Bezels Power cable and connector block RJ45 to 5-pin Ethernet adapter cable NMEA 0183 connector block Documentation pack Cable retainer kit Panel mounting kit Connections: NMEA 2000 - NMEA 2000 data J1939 - J1939 engine data USB - mouse, keyboard or mass storage NETWORK 1-3 - Ethernet network SD - microSD card reader HDMI OUT - HDMI video output VIDEO IN - composite video input HDMI IN - HDMI video input NMEA 0183 - NMEA 0183 data POWER - 12 - 24 V DC input, external alarm and power control