Cannon Rod Holder The Cannon Rodholder features a three-position rod-holding configuration to deliver the fastest baitcast or spinning rod pickup. A rear-position cradle holds baitcasting reels or spinning reels. The middle baitcasting cradle conforms to longer rod butts and shrtens the amount of rod extending through the back of the holder. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Extension Post f/Cannon Rod Holder - 2-Pack Features: Extends height of rod holder by 6" Allows forward & backward pivot adjustment Alignment key allows for 360° pivot while holding post securely in place

Allows rod holder to mount into the gunnel of the boat. Alignment key allows for 360 degree pivot while holding rod holder securely in place. Includes water-tight cap.

Bracket can be mounted on vertical or horizontal surface. Alignment key allows for 360 pivot while holding rod holder securely in place.

Rail Mount For mounting our single axis rod holder, this convenient rail mount attaches to either round or square rails. For 3/4" to 1-1/4"

Outrigger Rod Holder with Liner & Strap - Aluminum Features: Strong, Stylish and Functional Includes Liner and Strap Aluminum

Rod Holder - Heavy Duty - 0° - Stainless Steel The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years. Lee manufacturers of over 46 different models of flush mounted rod holders. Available in two sizes, Medium (2 in O.D.) and Heavy (2 1/4 in. O.D.) three different angles (0, 15 & 30 degree) in Stainless Steel. All of our Rod Holders, are polished by hand then electropolished Lee’s has the rod holder to suit any task.

Rod Holder - Medium - 0° - Stainless Steel The choice of boat manufacturers and consumers alike, Lee’s has been the Rod Holder Specialist for over 50 years. Lee manufacturers of over 46 different models of flush mounted rod holders. Available in two sizes, Medium (2 in O.D.) and Heavy (2 1/4 in. O.D.) three different angles (0, 15 & 30 degree) in Stainless Steel. All of our Rod Holders, are polished by hand then electropolished Lee’s has the rod holder to suit any task.

Aluminum Clamp-on Rod Holders Model:  RA5005SL Color:   Silver Fits:      2.375" O.D. Pipe Mount:  Vertial JUST CLAMP THEM ON! Aluminum rod holders that are as beautiful as they are functional. With no hassle or wear and tear on your boat you can install these rod holders with only an Allen Wrench. No lengthy trips to the tower builder for custom installation at custom prices. Simply place the two halves of the clamp around the pipe, insert the bolts and tighten. Install them wherever you like. If later, you don't like the position, simply move them. These Rod Holders are the perfect solution for boats with wiring or hydraulic lines inside their tower legs. Now you can install Rod Holders on your Tower, Hard Top, T-Top, Radar Arch, Rails, Poling Platform or any structure made from standard size aluminum pipe. All Holders come lined with a heavy duty white vinyl insert. The Clamping portion of the Rod Holder is precision made for an exact fit. Four Marine Grade Stainless Bolts assure an even clamping pressure and a secure bond. The clamp is welded to the tube with either a fin or an oval rod for maximum strength. The completed Rod Holder is then meticulously polished to a mirror finish. These holders are designed primarily for storage but may be used for light tackle trolling.

DUAL AXIS ADJUSTABLE ROD HOLDERS DOWNRIGGER MOUNT Mount our dual axis rod holders between the mounting base and swivel base of your Cannon downrigger for unparalleled rod positioning. A pistol grip release allows for quick, one-handed angle changes, and the innovative ratcheting adjustment system allows you to easily pull the holder to a vertical position. Full 360 degree rotation makes it the ultimate fishing accessory. WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Swivel Base Rod Holder RH577XL Vertical 0° Extra Long Tube Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

ShadeFin with White Fabric, Case & Fixed Rod Holder Mount Kit Add an extra layer of sun protection with ShadeFin by TACO Marine that easily attaches into rod holders, tops and arches for convenient, portable shade for almost any boat. ShadeFin’s ocean-inspired design provides expanded shade coverage for multiple areas of the boat, including fore, aft and sides of tops or anywhere there is a rod holder. ShadeFin’s fabric provides an excellent UPF 50+ rating of sun protection while boating and fishing, or when relaxing at the dock and sand bar. To anticipate the needs of many boaters, ShadeFin is available with either a fixed or adjustable rod holder mount, which inserts into any standard rod holder, or with a clamp-on mount for pipe or tube.  ShadeFin’s body houses the ribs and material, and is offered in all black or white. A protective mesh storage sleeve comes standard with the ShadeFin. To operate ShadeFin, remove the sleeve, mount to a desired location onboard and activate the underside release tabs. Structural ribs attached to weather-resistant sun-protecting fabric expand out from the body to lock the fin in place. ShadeFin is lightweight, portable and requires no drilling. Features: Light, compact and portable Easily mounts into any standard rod holder Kit comes with a Fixed Rod Holder Mount Adjustable Rod Holder Mount options available Clamp-on mounting options available for 3/4”, 1” schedule-40 Pipe and 1-1/4” O.D. tube Large coverage area of 5’ X 6’ UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts

ShadeFin with Black Fabric, Case & Fixed Rod Holder Mount Kit Add an extra layer of sun protection with ShadeFin by TACO Marine that easily attaches into rod holders, tops and arches for convenient, portable shade for almost any boat. ShadeFin’s ocean-inspired design provides expanded shade coverage for multiple areas of the boat, including fore, aft and sides of tops or anywhere there is a rod holder. ShadeFin’s fabric provides an excellent UPF 50+ rating of sun protection while boating and fishing, or when relaxing at the dock and sand bar. To anticipate the needs of many boaters, ShadeFin is available with either a fixed or adjustable rod holder mount, which inserts into any standard rod holder, or with a clamp-on mount for pipe or tube.  ShadeFin’s body houses the ribs and material, and is offered in all black or white. A protective mesh storage sleeve comes standard with the ShadeFin. To operate ShadeFin, remove the sleeve, mount to a desired location onboard and activate the underside release tabs. Structural ribs attached to weather-resistant sun-protecting fabric expand out from the body to lock the fin in place. ShadeFin is lightweight, portable and requires no drilling. Features: Light, compact and portable Easily mounts into any standard rod holder Kit comes with a Fixed Rod Holder Mount Adjustable Rod Holder Mount options available Clamp-on mounting options available for 3/4”, 1” schedule-40 Pipe and 1-1/4” O.D. tube Large coverage area of 5’ X 6’ UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts

700A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. More specifically, this rod holder is suitable for most walleye and panfish rods. An excellent choice for light trolling or still fishing. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 7 3/4 in. depth fits most standard rod sizes Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 7-3/4"

800A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. This is Panther's most popular rod holder. It will accept most heavy-duty trolling rods and is the choice of serious anglers and charter captains throughout the Great Lakes as well as the Pacific Northwest. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 10 in. depth for larger fishing rods Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 10"