PART #: TP125 Description: Top Plate Adaptor for 1.25" AngleGuard on Edson Steering System W x H x D: 9.5" x 9.5" x 1.25" NavPod Protects Your Electronics In Harsh Conditions Top Place Adaptor NavPod AngleGuards are designed to upgrade sailboat steering systems to accommodate mounting of electronics onto NavPods. Edson is a popular manufacturer of steering systems who has always used a 9.5" wide pedestal guard. Most of their pedestal guards are 1" in diameter. Lewmar (formally Whitlock) also has manufactured steering systems that use the 9.5" wide format. NavPod supplies the SG10 and AG10 as a easy retrofit onto either of these systems. Because of the clean and secure method of concealing wires and the need to accommodate large connectors and heavy radar cables within the Stainless Steel tubes, NavPod recommends the larger 1.25" diameter AngleGuards. Often the existing Top Plate needs to be bored out or replaced with the TP125 to accommodate the larger diameter. NavPod supplies Polished Stainless Steel feet with all 1.25" AngleGuards.

TP325 Top Plate f/Converting Merriman/Yacht Specialties Steering Systems to 12" Wide 1.25" Diameter AngelGuard 12" Top Plates are used for upgrading from an existing 1" diameter pedestal guard to a 1.25" StraightGuard or AngleGuard. Specifically designed for Converting Merriman or Yacht Specialties steering systems. 12" Top Plates Include: 316 Stainless Steel Mirror Polished Finish Precision Laser Cut

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

ADAF3 Modular Top Plate for FLIR M300 Series Thermal Cameras f/Mounts Ending in M1 or M2 Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.  Unique Design No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics. Note: This only applies to the ADA-R1, ADA-S1 & ADA-S2 Top Plates King Starboard The ADA-R2, ADA-S3, ADA-S4 & ADA-F1 Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.

Starlink Maritime Top Plate for Seaview M1 Style Modular Mounts Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features:  Water-tight gasket in the center of the plate to pass the Starlink cable Predrilled and all hardware needed to mount the Starlink is included *Not light bar compatible

Starlink Maritime Top Plate for Seaview M1 & M2 Style Modular Mounts Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features: Starlink Wedge Base hole pattern pre-dimpled in this modular top plate Water-tight gasket in the center of the plate to pass the Starlink cable The 1” thick starboard plate can accommodate a Seaview light bar

23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

Starlink Maritime Top Plate for Seaview M1 Style Modular Mounts - Black Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "Swiss Cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features:  Water-tight gasket in the center of the plate to pass the Starlink cable Predrilled and all hardware needed to mount the Starlink is included *Not light bar compatible

12.5" Dual Mount for Most Radar Domes - Top for Sat Domes - Top Plate Required Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*

22.5" Dual Mount for Up To 4.5' Open Array Radar - Top for Sat Domes - Top Plate Required  Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*

13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

28" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.   Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.   Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Seperately

Starlink Maritime Black Top Plate for Seaview M1 & M2 Style Modular Mounts Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "Swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features: Starlink Wedge Base hole pattern pre-dimpled in this modular top plate Water-tight gasket in the center of the plate to pass the Starlink cable The 1” thick starboard plate can accommodate a Seaview light bar

5" Aft Leaning Mount with ADAR1 Top Plate This Seaview Modular Radar Mount works with 18" - 24" closed dome radars. The modular design allows you to add various accessories and different top plates at any point, thus making it a cost-effective choice.  Included ADAR1 Top Plate Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "Swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.

5" Modular Mount FWD Raked 7" x 7" Base Plate - Top Plate Required This Seaview Modular Radar Mount works with 18" - 24" closed dome radars. The modular design allows you to add various accessories and different top plates at any point, thus making it a cost effective choice.  Modular Top Plate A Seaview Modular Top Plate is required to mount a radar, satellite dome, camera or search light, and is sold separately. Modular Design The modular design allows the user to not have to replace the entire mount when a different radar or satdome is used. Instead the user can just replace the top plate. Compact Design Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must.