|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
61.99 |
|
|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
62.99 |
|
|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
63.99 |
|
|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
66.99 |
|
|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
71.99 |
|
|
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
72.99 |
|
|
3 Blade stainless propeller for Mercruiser Bravo II stern drive engines with 19 tooth spline and thru hub exhaust.
|
739.99 |
|
|
Smoother and lower effort steering system. Quick connect feature on both cable and spent travel tube side. No tools required to snap steering cable or spent travel tube in place. Easy system installation, single steering cable to route with standard 8" bend radius. Fits standard dash cut out for Safe-T and 4.2 bracket. Gear train is custom designed to allow the smallest foot print with the lowest effort available in a mechanical Helm. Improved NFB clutch "feel" to allow smoother clutch release. Includes NFB helm, bezel and Xtreme cable.
|
433.99 |
|
|
Heavy duty black molded plastic base. Use with SFE, AGC or MDL fuses up to 20 amps. Brass fuse clips and 8-32 terminal screws. Common bus bar connects the hot side of fuses for power feed. Bus bar has 8-32 stud terminals for main power / ground main connections. Rated 20 amps per circuit, 120 amps total for block.
|
15.83 |
|
|
Gasoline and solvent-resistant primer bulbs meet or exceed EPA/CARB Fuel Permeation Regulations. Stainless steel clamps and dual internal check valves to ensure rapid prime while preventing fuel flow back.
|
29.79 |
|
|
Fittings for 3300 and 33C series shift and throttle control cables.
|
16.38 |
|
|
OMC 479 type cable (1979 & later). Complete drop-in replacement cable for OMC O/B and I/O's. Stainless steel and brass fittings. 6" minimum bend radius. WHILE QUANTITIES LAST.
|
73.99 |
|
|
3 Blade stainless interchangeable hub propeller for 40-140 horsepower engines with thru hub exhaust, 4-1/4" gear case. Category D prop. Requires RBX™ hub kit for installation.
|
339.99 |
|
|
3 Blade stainless interchangeable hub propeller for 40-140 horsepower engines with thru hub exhaust, 4-1/4" gear case. Category D+ prop. Requires RBX™ hub kit for installation.
|
356.99 |
|
|
Prop kits containing thrust washer, spacer, washer, nut and cotter pin. Complete kit contents depends upon application.
|
19.62 |
|