|
Scanpod Instrument Pod - Uncut - Arm Mounted - Fits 1" - 1.3" Rails
Current sailboat designs often have very open cockpits with few options for installing retro-fit instruments.
Options available to install a 7" display or standard instrument.
Arm Mounted:
Extend the Rail Pod away from narrow or crowded rails for better viewing
Designed to ensure the Pod is always positioned for best viewing, whatever the angle of the rail
|
386.89 |
|
|
GP1300 InstrumentPod Uncut fits 3 Instruments for 9.5" Guard
NavPod's InstrumentPod GP1300 for 9.5" Guard is used for mounting three instruments in a single NavPod at the helm or companionway.
An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway.
All InstrumentPods Include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-proof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
|
314.17 |
|
|
GP140 InstrumentPod Uncut for 9.5" Wide Guard
NavPod InstrumentPod GP2400 Series for 12" Guard are used for mounting two - four in a single NavPod at the helm or companionway.
An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway.
All InstrumentPods include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-proof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
|
357.80 |
|
|
GP2400 InstrumentPod Uncut for 12" Wide Guard
NavPod InstrumentPod GP2400 Series for 12" Guard are used for mounting two - four in a single NavPod at the helm or companionway.
An InstrumentPod can be mounted on a StraightGuard or use a Double Bend AngleGuard to fit an InstrumentPod on the top vertical section and SailPod below on the angled section. It can also be used with the SK312 Companionway Mount for positioning sailing instruments above the companionway.
All InstrumentPods include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-proof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
|
357.80 |
|
|
GP1200 SailPod Uncut for 9.5" Wide Guard
GP1200 Series for 9.5" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section.
SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications.
Sizing:
Overall Size: 11.3"H x 16.5"W x 5.55"D
Usable Face: 9.85"H x 15.18"W x 4.25"D
Max Cutout:9"H x 14.25"W
All SailPods include:
Acrylic capped ABS plastic
Chromed stainless steel tamper-proof fasteners and wrench
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
|
418.90 |
|
|
GP2200 SailPod Uncut for 12" Wide Guard
GP2200 Series for 12" Guard, SailPods for Sail are for mounting a single radar or chartplotter at the helm where you can easily operate and clearly see the fine details of the screen. A single SailPod is best mounted on a Single Bend AngleGuards or use a Double Bend AngleGuards to fit an InstrumentPod on the top vertical section and SailPod below on the angled section
SailPod for Power are for mounting on a SK135 Stachion Kit can be used to mount a SailPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SailPod for overhead mounting applications.
Sizing:
Overall Size: 11.3"H x 16.5"W x 5.5"D
Usable Face: 9.85"H x 15.18"W x 4.25"D
Max Cutout: 9"H x 14.25"W
All SailPods include
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners and wrench
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
|
418.90 |
|
|
GP1500 SystemPod Uncut for 9.5" Wide Guard
GP1500 Series for 9.5" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
Usable Face for Uncut
15"W x 6"H
*See Literature tab for an image with dimensions
|
314.17 |
|
|
GP2500 SystemPod Uncut for 12" Wide Guard
GP2500 Series for 12" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
Sizing:
Usable Face: 15"W x 6"H
All SystemPods include
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
*See Literature tab for an image with dimensions
|
314.17 |
|
|
GP1600 SystemPod Uncut for 9.5" Wide Guard
GP1600 Series for 9.5" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
Usable Face: 19.75"W x 6"H
All SystemPods include
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
*See Literature tab for an image with dimensions
|
392.71 |
|
|
GP2600 SystemPod Uncut for 12" Wide Guard
GP2600 Series for 12" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
Sizing:
Usable Face: 19.75"W x 6"H
All SystemPods include
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
*See Literature tab for an image with dimensions
|
392.71 |
|
|
GP2040 SystemPod Uncut for 12" Wide Guard
Usable Face:7.375H x 17.5W x 5D
Max Cutout:7"H x 17" W
NavPod GP2040 Series for 12" Guard SystemPods are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
The Hi-Gloss Material
NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity.
The Waterproof Seal
All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics.
The Nickel Chrome Plated Screws
We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling!
The Manufacturing Process
Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances.
Our Commitment to Quality
We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.
*See Literature tab for an image with dimensions
|
383.99 |
|
|
PART #:
GP1040
Description:
Uncut (usable face = 17.5"w x 7.375"h)
W x H x D:
20.25" x 9.5" x 6.125"
NavPod Protects Your Electronics In Harsh Conditions
Un-Cut NavPods are for you to choose your own layout or for mounting electronics that NavPod doesn't provide a Pre-Cut for. The face of the NavPod can easily be cut with a "Rotozip". It's a small handheld router style cutter that shreds the material while cutting. This eliminates any melting of the plastic material. It is also important to note that when selecting a possible Un-cut NavPod, the depth measurement stated in the chart is overall outside measurement. Actual internal clearance can be reduced by curvature from the design or molded indents for the mounting system. This can reduce the overall and needs to be considered when making a determination of actual available depth clearance.
Watertight Silicone Seal
Keeps rain and salt water spray off electrical connections on the back of electronics
Tamperproof
Special fasteners and wrench are included that provide security and convenience to leave electronics on-board
Concealed Wiring
No loose wires are exposed to corrosion and UV damage
Clean Installation
The clean look of flush mounting. Mount your display where you can best see and reach it.
Pre-Cut Models
Come with a Flush Mount Kit, which includes the specific gasket and mounting hardware for your electronics if not supplied by manufacturer with unit.
|
383.99 |
|
|
PART #:
GP1170
Description:
Uncut (usable face = 20.77"w x 9.64"h)
W x H x D:
N/A
NavPod Protects Your Electronics In Harsh Conditions
Un-Cut NavPods are for you to choose your own layout or for mounting electronics that NavPod doesn't provide a Pre-Cut for. The face of the NavPod can easily be cut with a "Rotozip". It's a small handheld router style cutter that shreds the material while cutting. This eliminates any melting of the plastic material. It is also important to note that when selecting a possible Un-cut NavPod, the depth measurement stated in the chart is overall outside measurement. Actual internal clearance can be reduced by curvature from the design or molded indents for the mounting system. This can reduce the overall and needs to be considered when making a determination of actual available depth clearance.
Watertight Silicone Seal
Keeps rain and salt water spray off electrical connections on the back of electronics
Tamperproof
Special fasteners and wrench are included that provide security and convenience to leave electronics on-board
Concealed Wiring
No loose wires are exposed to corrosion and UV damage
Clean Installation
The clean look of flush mounting. Mount your display where you can best see and reach it.
Pre-Cut Models
Come with a Flush Mount Kit, which includes the specific gasket and mounting hardware for your electronics if not supplied by manufacturer with unit.
*See Literature tab for an image with dimensions
|
445.08 |
|
|
New Items added at CLR Marine today:
SCANPOD DECK POD UNCUT USABLE 10.3 X 15.0 DEEP WHITE
GARMIN CARRY CASE FOR ETREX 10 20 30
GARMIN HOOK & LOOP SPINE MOUNT FOR ETREX 10 20 30
GARMIN AUTO FRICTION MOUNT FOR ETREX 10 20 30 RINO 610 650
GARMIN BELT CLIP FOR ETREX 10 20 30
KESTREL TACTICAL MOLLE/PALS BLACK CASE F/ 1000 TO 4000
KESTREL TACTICAL MOLLE/PALS BROWN CASE F/ 1000 TO 4000
KESTREL TACTICAL MOLLE/PALS GREEN CASE F/ 1000 TO 4000
KESTREL TACTICAL MOLLE/PALS CAMOUFLAGE CASE 1000 T0 4000
|
|
|
Scanpod 7" Helm Pod Rail Mount
Features:
Applications: Designed for (1) 7" Instrument
Current sailboat designs often have very open cockpits with few options for installing retro-fit instruments
The Rail Pod gives you an option for fitting smaller displays and instruments directly onto a rail, in a position which suits you
Rail Mounted
Universal Fixing
Fits pedestal rails from 25mm to 33.7mm (0.98" - 1.33")
Fit your display onto standard and curved rails
Great Viewing Options Viewing angle can be set upon installation
Cables are routed internally through the clamp and onto the rail
Increased Protection
Pod seal is manufactured from a high tear strength silicone, it has a very high resistance to heat and UV so you can have confidence that it won't deteriorate over time
Supplied Uncut - As standard you will receive your Scanpod uncut
|
348.14 |
|