13' Bright Silver/Black Spike - Step Tube 1-3/8" - No Spreader The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by. Features: 13' Bright Silver/Black Spike MX Step-tube style No spreader

TACO Flared Weld-On Rod Holder 9-3/4"L x 1-3/4"ID - White Liner Polished Finish Taco Marine weld-on Aluminum rod holder is Brite Dip anodized for lasting protection and superior luster. Specially formulated, fungal-resistant PVC liners are tapered to fit snugly with flared rod holder design. Taco Marine Rod Holders with flared design allow for easy rod placement. Welded I-Beam pin construction seats rod butt securely in place and is proven to be 2-1/2times stronger than competitive rod holders. Features: Brite Anodized Aluminum Designed for welding to towers, T-tops, radar arches, railings, and leaning posts Welded I-Beam securely Seats rod butt Form-fitted Anti-fungal PVC liners Made in USA

Flared Weld-On Rod Holder 9-3/4"L x 1-3/4"ID - White Liner Polished Finish - 3/8" Coped Blade Taco Marine weld-on Aluminum rod holder is Brite Dip anodized for lasting protection and superior luster. Specially formulated, fungal-resistant PVC liners are tapered to fit snugly with flared rod holder design. Taco Marine Rod Holders with flared design allow for easy rod placement. Welded I-Beam pin construction seats rod butt securely in place and is proven to be 2-1/2 times stronger than competitive rod holders. Features: Brite Anodized Aluminum Ideal for welding to towers, t-tops, radar arches, railings, and leaning posts Flared style with 3/8" Coped Blade Welded I-Beam securely seats rod butt Includes form-fitted PVC anti-fungal white liner Three year limited warranty Made in USA

15' Bright Silver/Black Spike - Step Tube 1-3/8" - No Spreader The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by. Features: 15' Bright Silver/Black Spike MX Step-Tube Style No Spreader

90° Tinned Copper Lug #1 - 3/8" - 2-Piece 90° bend for ease of wire routing.

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ      230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet     Part # 0115-0064-0300  

Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-3/8 may have been modified to handle these chemicals.   March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.      Unit System 60Hz 50Hz Max Flow 2.3 GPM 8.7 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ          230V 50/60HZ   Type Centrifugal Mag Drive Inlet 3/8"OD Outlet 3/8"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet

Round Drawer Pull 1-3/8" Round Recess Mount, 3/8" Deep 2-Pack

1-1/2" NPT x 1-3/4" ID Bronze Full Flow 90° Elbow Pipe to Hose Fitting Features: 90 degree Male NPT x Hose connection C83600 Bronze Sizes from 1/2" to 3" Full Flow UL Listed 647B Note- C83600 bronze fittings are not in compliance with NSF-61 and therefore are not intended for use in potable water systems

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/8" SHAFT 2 1/4" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

PSS Shaft Seal Maintenance & Parts Replacement Kit FOR 1 3/8" SHAFT 2 1/2" TUBE As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. The PSS bellow should be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced. Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.

Material: 304 Stainless Steel Stock: 5/16" Eye Ring Diameter: 1" Thread Length: 1-3/8" Wall Plate Size: 3/4" x 2-1/4"

Shortside Door Hinge Size:1-3/8" x 2-1/4" Fastener: #10(5) Material: Black Nylon

Shortside Door Hinge Size:1-3/8" x 2-1/4" Fastener: #10(5) Material: White Nylon

PSS Shaft Seal 1-3/8" Shaft 2-1/4" Tube Shaft Diameter: 1-3/8" Stern Tube Diameter (D): 2-1/4" to 2-3/8" Total Length (A): 7.38" Total Length (compressed) (Compressed A): 6.38" Rotor Diameter (B): 2.875" Carbon Cuff Diameter (C): 2.5" Stern Cuff Length (E): 1.5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm). The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation. **As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced." Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater. The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.