|
HTM-2 Fender 8.5" x 20.5" - Black
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|
|
HTM-2 Fender 8.5" x 20.5" - Blue
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|
|
HTM-2 Fender 8.5" x 20.5" - White
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|
|
Stainless Steel Stud 1.25" Base #10 x 24 Thread 2.5" Tall
Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate.
|
56.27 |
|
|
HTM-2 Fender 8.5" x 20.5" - Graphite
In keeping with the Polyform tradition of quality, the HTM (hole-through-middle) boat fender was designed to provide maximum protection in a wide variety of applications. Vertical ribs for extra protection, reinforced tube ends to prevent lines from pulling through if the fender gets caught in a tight spot, and extra wall thickness to resist punctures and tears are just a few of the features of this high-quality fender has to offer.
The HTM Series fender is designed to provide protection and stand-off for larger vessels between 20 to 50 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced tube ends
Designed for medium-duty use in both permanent protected and unprotected moorings
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 8.5" x 20.5" (21.6 x 52.1cm)
Tube Diameter - 0.625" (1.6cm)
Circumference - 26.7" (67.9cm)
Volume - 4.7 gallons (17.8L)
Boat Size - 25' - 30' (7.6 - 9.1M)
Weight - 4.7lb
*Sold as an Individual
|
61.68 |
|
|
Swivel Shackle - 5/16" Pin - 2-3/8"L x 21/32"W
Features:
Coined head pin 7.9mm(5/16") Diameter Pin
Grade 316 Stainless Steel bodies and pins
Stainless Steel ball bearing race
|
33.11 |
|
|
Wide Dee Shackle - 3/8" Pin - 2-7/32"L x 1-5/32"W
Features:
3/8" pin diameter
High strength to weight ratio
|
27.00 |
|
|
Long Dee Shackle - 3/8" Pin - 2-3/8"L x 23/32"W
Features:
High strength to weight ratio
Grade 316 Stainless Steel bodies and pins
Drilled Shackle pin for siezing wire
|
26.46 |
|
|
Twisted Shackle - 5/8" Pin - 2-1/8"L x 5/8"W
Features:
High strength to weight ratio
Grade 316 Stainless Steel bodies and pins
Drilled shackle pin for siezing wire
|
28.74 |
|
|
Bow Shackle - 3/8" Pin - 2-1/16"L x 13/32"W
Features:
High strength to weight ratio
Grade 316 Stainless Steel bodies and pins
Drilled shackle pin head for seizing wire
|
28.22 |
|
|
The RAM-D-202U consists of a 2.25" diameter rubber ball, connected at right angles to a 3.68" diameter round plate. The plate has pre-drilled holes in the base plate, including two holes at 180 degrees and three holes at 120 degrees.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
2.25" Rubber Ball "D" Size
|
28.64 |
|
|
RAM Large Cable Manager f/2.25" Diameter Ball Bases
The RAM Cable Manager creates an integrated route for electrical wiring and cleanly covers installation holes. A great addition to any surface mounting application. The RAM Cable Manager is made of glass filled nylon which has the benefit of creating a barrier between the RAM Surface Mount and the attachment area; minimizing vibration while reducing fiberglass and gel-coat damage.
Compatible RAM Mounts:
Compatible with all 2.25" diameter ball bases that contain a three hole, 120 degree hole pattern.
Material:
High Strength Composite and Glass Filled Nylon
IMPORTANT:
To prevent galling of threads during assembly, it is imperative that all threads are lubricated with oil prior to assembly.
Note:
The "U" in the part number reflects product packaged in poly bag. RAM ball base not included with purchase.
|
18.47 |
|
|
D Size 2.25" Ball Mount w/11" X 3" Rectangle Plate, 3.68" Round Plate and Hi-Torq™ Wrench
The RAM-D-111U-C consists of a short double socket arm, 3.68" diameter round base and 11" x 3" rectangular base. The round base contains pre-drilled holes, including two holes at 180 degrees and three holes at 120 degrees. The rectangle base contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more.
The RAM-D-111U-C is Compatible With:
Garmin Fishfinders and GPS Chartplotters
Humminbird Fishfinders and GPS Chartplotters
Lowrance Fishfinders and GPS Chartplotters
Raymarine Fishfinders and GPS Chartplotters
Overall Height:
8.125"
Weight Capacity:
Up to 15 lbs.
Weight:
3.45 lbs.
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
2.25" Rubber "D" Ball Size
Hi-Torq™ Wrench
The RAM handle wrench is designed to be used with the knob found on "D" size ball arms and mounts. The wrench matches the shape of the knob found on the side of "D" arms, and lets you give the arm an extra tight grip. This wrench was originally made for the military when using the RAM mounts in cold weather, and the knob could not be tightened by hand.
|
144.56 |
|
|
The RAM-D-201U powder coated marine grade aluminum 6.88" double socket arm allow for connnection to a 2.25" diameter ball. Socket technology allows for almost infinite adjustment and perfect viewing angles.
Dimensions:
Overall Length: 8.375"
Socket-To-Socket Length: 6.5625"
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
2.25" Rubber Ball "D" Size
|
69.64 |
|
|
The RAM-D-201U-E powder coated marine grade aluminum LONG double socket arm allows for connnection to a 2.25" diameter ball. Socket technology allows for almost infinite adjustment and perfect viewing angles.
Dimensions:
Overall Length: 12.875"
Socket-To-Socket Length: 11.1875"
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
2.25" Rubber Ball "D" Size
Note:
The "U" in the part number reflects product packaged in poly bag.
|
92.40 |
|