|
March Mag-Drive Centrifugal Pumps Bronze Center Inlet 12VDC 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
479.06 |
|
|
March 809 BRC HS 12VDC Mag-Drive Pump
March Mag-Drive Centrifugal Pumps Bronze 12VDC High Speed 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 12VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
499.69 |
|
|
March 809 BRC HS 24VDC Mag-Drive Centrifugal Pumps Bronze 24VDC High Speed 5.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 24VDC High Speed 5.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
501.56 |
|
|
Jabsco 18690-0010 Heavy Duty Macerator Pump 115V 3" Ports
Pump Body:
Plastic, Self-Priming Flexible Impeller with Stainless Steel Wearplates.
Port Size:
Inlet – 3" Slip on Hose
Outlet – 1" ID Hose Barb
Flow:
14 GPM
Macerator:
Cast Bronze Cutter Plate reduces particle size to 1/8" maximum.
Impeller:
Nitrile
Shaft Seal:
Lip Type
Motor:
115 Vac, AC Induction Type Single Phase, 60 Hz Thermal Overload Protection.
APPLICATIONS
The Jabsco 18690-0010 AC macerator pump unit is the ideal answer to waste handling problems for marine, recreational vehicle and domestic uses. The macerator section grinds waste down to a particle size of 1/8" maximum so it can be pumped easily through a 1" hose discharge line. The pump is self-priming, permitting the unit to be mounted above or below the tank in a convenient location. For optimal efficiency, locate pump as close to waste source as practical. Empties a 30 gallon holding tank in only 3 minutes. The 18690-0010 waste pump will macerate and pump all waste and tissue normally found in marine waste systems.
|
1079.81 |
|
|
March Mag-Drive Centrifugal Pump w/Ports W/115V Mtr
• March MDX pumps can deliver a maximum flow of 6.0 GPM (22 LPM), are capable of serving applications with a maximum head of 7 ft. (1.6m) Fittings are for hose connections.
• Applications include coffee dispensers, aquariums, bio-medical, dryers, ice makers, electrostatic painting, photographic processing, and vending equipment.
• The plastic parts are molded out of glass filled polypropylene. The spindle housing is molded carbon filled PVDF plastic. The O-rings are Buna N rubber. The magnet is a glazed ceramic.
• The motors are 115 volt, 1750 RPM, 50/60 Hz, 1 phase A.C. 230 volt motors are available. Motors are all thermal overload protected and are UL recognized
March Pump Mag-Drive Centrifugal Pump 115V Air Cooled 5.5GPM 1/2" Hose Ports
|
297.38 |
|
|
March MDX-MT3 Pump 115V 1/2" Ports
|
367.58 |
|
|
March 0135-0109-1000 Motor
Motor 115 Volt AC 60 HZ 1750 RPM SB without a base 38" Cord for March Pumps MDX and MDXT
|
190.32 |
|
|
March TE-MDX-MT3 Magnetic Drive Pump
Uses include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
The TE-MDX-MT3 has pumped Acetic Acid, Acetone, Benzene Sulfonic Acid, Citric Acid, Ethanolamine, Freon 11, Potassium Hydroxide, Potassium Permanganate, Sodium Hydroxide (Caustic Soda), Fresh Water, Salt Water, DI Water, and many more chemicals.
March Pump's industrial TE-MDX-MT3 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer.
It is capable of generating a maximum flow of 10 gallons per minute at 1 foot, and its maximum head is 17 Feet (or around 7PSI).
The standard wet end (the materials that come into contact with the solution) is composed of Ryton, Viton, and Ceramic. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread.
The standard motor is a 1 Phase 115V or 230V 0.066 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz.
The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-MDX-MT3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids and solvents.
Max Flow: 10 GPM or 35 LPM
Max Head: 17 FT or 3.7 M
Power: .066 HP or .049 KW
Electrical: 1Ph 115/230V 50/60HZ
Type: Centrifugal Mag Drive
Inlet: 1/2"MPT
Outlet: 1/2"MPT
Wet End: Ryton (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Viton (O-Ring)
Motor: Explosion Proof Motor
|
2107.80 |
|
|
March MDX 5/8 Pump 5/8" Ports 115V
|
290.55 |
|
|
March TE-MDX-MT3
Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March magnetic drive 10 gpm/35 lpm chemical pump having 1/2" MPT inlet size and 1/2" MPT outlet size features 75 psi maximum pressure and 115/230 VAC voltage rating
March Pump's industrial TE-MDK-MT3 is an American sealless centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 10 gallons per minute at 1 foot, and its maximum head is 17 feet (or around 7PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), viton, and ceramic. The inlet connection is 1/2 in male pipe thread, and the outlet is 1/2 in male pipe thread. The standard motor is a 1 phase 115 V or 230V 0.04 horsepower fan cooled motor, which can be run on either 50 or 60 hertz. The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-MDK-MT3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Totally enclosed fan cooled
Series MDX and MDK are centrifugal magnetic drive pumps, eliminating the need for a shaft seal
Pumps can be serviced with a screwdriver
Item: Chemical Pump
Type: Magnetic Drive
Series: MDX
Flow Rate: 10 gpm at 60 Hz, 35 lpm at 50 Hz
Inlet Size: 1/2 in MPT
Outlet Size: 1/2 in MPT
Voltage Rating: 115/230 VAC
Motor Specifications: 1-Phase, 50/60 Hz, 0.066 hp, 95/115 W, 2850/3450 rpm
Maximum Head: 17 ft at 60 Hz, 3.7 m at 50 Hz
Maximum Pressure: 75 psi
Temperature Rating: 93 deg C
Material: Ryton
Dimensions: 12.42 in Length x 8.02 in Width x 7.19 in Height
|
747.90 |
|
|
March 0135-0036-1000 Motor 115 volt
Motor AC 115V 50/60HZ 3500 RPM SB No Base 38"Cord used on models MDX-3 and MDXT-3
|
176.80 |
|
|
March 0135-0112-1000 230V Motor
Motor AC 230 Volts 50/60 HZ 1750R PM SB without the Base 38" Cord for March Pumps MDX and MDXT
|
231.92 |
|
|
Applications for the MDX-MT3-AM Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March Pump's industrial MDX-MT3-AM is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 9 gallons per minute at 1 foot, and its maximum head is 28 Feet (or around 12PSI). The standard wet end (the materials that come into contact with the solution) is composed of Ryton, Viton, and Ceramic. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.125 Horsepower Compressed Air Motor which requires 21PSI. The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March MDX-MT3-AM centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Max Flow
9 GPM
34 LPM
Max Head
28 FT
8.8 M
Power
.125 HP
.093 KW
Electrical
21PSI or 3CFM
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Ryton (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Viton (O-Ring)
|
828.00 |
|
|
March MDX 230V Pump 230V 1/2" Ports
|
335.40 |
|
|
March Pump- Mag-Drive Centrifugal 115V Pump 1X3/4 Smooth Ports
• March AC-4C-MD and BC-4C-MD series pumps can deliver a maximum flow of 14 GPM (50 LPM), and are capable of serving applications with a maximum head of 21.5 ft. (4.7 m) (49 ft. [15.6 m] when driven by an air motor).
• Applications include electronic medical equipment, etching machines, photo processing equipment, hospital thermal blankets and food heating cabinets.
• Standard construction is of polypropylene, with optional wetted materials that include Ryton or Kynar. Other materials include: Ceramic, Buna N rubber, and Viton for total chemical compatibility.
• Drive choices are a 1/12 HP (.062 kw), 3450 rpm air cooled or a 1/10 HP (.074 kw) 3450 rpm blast-cooled, 115-volt single phase, 50/60 Hz. motor. 230 volt optional.
March Pump Mag-Drive Centrifugal Pump 115V Air Cooled 14GPM 1" Hose Inlet, 3/4" Hose Outlet
|
506.86 |
|