3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

Smoother and lower effort steering system. Quick connect feature on both cable and spent travel tube side. No tools required to snap steering cable or spent travel tube in place. Easy system installation, single steering cable to route with standard 8" bend radius. Fits standard dash cut out for Safe-T and 4.2 bracket. Gear train is custom designed to allow the smallest foot print with the lowest effort available in a mechanical Helm. Improved NFB clutch "feel" to allow smoother clutch release. Includes NFB helm, bezel and Xtreme cable.

Heavy duty black molded plastic base. Use with SFE, AGC or MDL fuses up to 20 amps. Brass fuse clips and 8-32 terminal screws. Common bus bar connects the hot side of fuses for power feed. Bus bar has 8-32 stud terminals for main power / ground main connections. Rated 20 amps per circuit, 120 amps total for block.

Fittings for 3300 and 33C series shift and throttle control cables.

Gasoline and solvent-resistant primer bulbs meet or exceed EPA/CARB Fuel Permeation Regulations. Stainless steel clamps and dual internal check valves to ensure rapid prime while preventing fuel flow back.

Improves engine performance and efficiency. Dissolves gum and varnish from entire fuel system - carbureted or injected. Removes internal carbon deposits from intake ports, valves, combustion chambers, pistons, and frees sticky rings. Displaces moisture and stabilizes fuel during storage periods. Designed for use in 2-cycle and 4-cycle marine engines. WHILE QUANTITIES LAST.

Mercury/Mercruiser 600A type cable. Complete drop-in replacement cable for Mercury/Mercruiser engines. Stainless steel & brass fittings. Stainless cable wire. WHILE QUANTITIES LAST.

OMC 479 type cable (1979 & later). Complete drop-in replacement cable for OMC O/B and I/O's. Stainless steel and brass fittings. 6" minimum bend radius. WHILE QUANTITIES LAST.

3 Blade aluminum propeller for 35-50 horsepower engines with 13 tooth spline and thru hub exhaust. 3-1/4" Gear Case.

Control Engine Trim/Tilt, Jackplate or Horn with Pro-Trim Single, or any two functions with Pro-Trim Dual. Fits Safe-T mechanical steering, Rack & Pinion Steering, NFG No Feedback steering(all helms), SeaStar and SeaStar PRO hydraulic steering, Command 200 Rack & Pinion, Baystar, Sport, Sport Plus or Classic Tilt mechanism. "Momentary-On" switch is off in its center "at-rest" position. Switch actuates in up and down directions. U.V. stabilized ABS switch cover blends with dash. Strainless steel bracket fits most steering & adjusts for regular or deep dish wheels. Heavy duty marine wiring harness, color coded to match existing trim & jackplate wiring. Mylar decals for labeling of switch functions. Mounting hardware, instructions included. Display packed.