 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
62.99 |
|
 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
63.99 |
|
 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
65.99 |
|
 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
66.99 |
|
 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
71.99 |
|
 |
3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.
|
72.99 |
|
 |
Smoother and lower effort steering system. Quick connect feature on both cable and spent travel tube side. No tools required to snap steering cable or spent travel tube in place. Easy system installation, single steering cable to route with standard 8" bend radius. Fits standard dash cut out for Safe-T and 4.2 bracket. Gear train is custom designed to allow the smallest foot print with the lowest effort available in a mechanical Helm. Improved NFB clutch "feel" to allow smoother clutch release. Includes NFB helm, bezel and Xtreme cable.
|
433.99 |
|
 |
Fittings for 3300 and 33C series shift and throttle control cables.
|
16.38 |
|
 |
Heavy duty black molded plastic base. Use with SFE, AGC or MDL fuses up to 20 amps. Brass fuse clips and 8-32 terminal screws. Common bus bar connects the hot side of fuses for power feed. Bus bar has 8-32 stud terminals for main power / ground main connections. Rated 20 amps per circuit, 120 amps total for block.
|
15.83 |
|
 |
Gasoline and solvent-resistant primer bulbs meet or exceed EPA/CARB Fuel Permeation Regulations. Stainless steel clamps and dual internal check valves to ensure rapid prime while preventing fuel flow back.
|
29.79 |
|
 |
High performance permanent magnet gear reduction starter. 2 long bolt staggered pattern, CW rotation. use with late model 3.0L engines with 14" flywheel. Uses SW450 replacement solenoid and DV450 replacement drive assembly with 11 tooth drive gear. Will replace 9-tooth OEM version. NOTE: Does not include mounting bolt kit (required if replacing 10MT style starters). Order MBK450 Mounting Kit separately.
|
211.86 |
|
 |
OMC 479 type cable (1979 & later). Complete drop-in replacement cable for OMC O/B and I/O's. Stainless steel and brass fittings. 6" minimum bend radius. WHILE QUANTITIES LAST.
|
64.99 |
|
 |
Designed specifically to be used with late model Mercury 4000 series controls. Engineered to significantly reduce or eliminate cable "Wig-Wag", this design results in a significantly improved feel with less shifting effort. Improves the feel of the Mercury 4000 Series Controls. Nickel plated brass swivel tube. WHILE QUANTITIES LAST.
|
75.99 |
|
 |
3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
175.99 |
|
 |
4 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.
|
192.99 |
|
