XKA Aluminum Alloy Trim Tab Kit with ALC-1 Control - 12 x 18 The Lectrotab Aluminum Alloy trim tabs are uniquely designed to meet the needs of Aluminum hulled boats and are an economical option for all boats.  All Aluminum Alloy tabs are fabricated with an extremely strong "no-break" polypropylene hinge.  All Aluminum tabs are sealed with a corrosion resistant epoxy coating.  Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design.  The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation.  The actuator assembly is packaged in a non-metallic permanently sealed housing.  No components need to be installed inside the boat.  Most importantly, unlike hydraulic trim tabs, there is no oil to leak out.  The actuator incorporates either a standard or low profile transom mounting bracket.  The Automatic Leveling Control (ALC) will automatically adjust your trim tabs to maintain a level boat for a more comfortable and enjoyable ride. Additionally, the ALC automatically corrects the roll from side to side and pitch from fore to aft to enhance your boating experience and improve your fuel economy.  Features: All Tabs sealed with a corrosive resistant epoxy coating Equivalent strength to 10 gauge stainless steel "No Break" polypropylene hinge tested over 300,000 cycles to a 90° bend without failure Upper ram seal location cannot be damaged due to fouled ram or barnacle growth Utilizes internal pressure equalization system Internal brake system prevents unwanted tab movement when under way or backing down Quiet operation Actuators are fully load tested to push 1000 lbs of force Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water Technical Specifications: Trim Tab Size (L x W) - 12" x 18" (30 x 46 cm) Boat Length - 20' to 40' (6 to 12 M) Trim Tab Material - Marine grade 6005-T5 Aluminum Alloy  Actuator DC Voltage - 12 V Actuator Stroke Length - 2.25" (57 mm) Actuator Cable Length  - 23' (7 M) Actuator Vertical Height - 11.875" (302 mm) Control Dimensions (W x H) - 3.15" x 3.07" (80 x 77 mm) Control Mounting Hole Cutout - 2" (50 mm) Control Operating Voltage - 12 or 24 V In the Box: One (1) Automatic Leveling Control Two (2) Aluminum Alloy tabs Two (2) actuators w/23' (7 M) cables Instruction Manual  *Sold as a Kit

WakeSurf Edge Pro II Mega Wake Shaper - 14" x 18" FATSAC's huge water displacement wing for maximum wave height! Recommended boat 21’ or longer, have a 325hp engine or greater, use with FATSAC water ballast systems. Level load your boat to keep the nose down for the captain’s visibility and a long wake. Features: Patented Concave Water Channeling Wing - Our concave channeling wing surface pushes more water to increase the length of the wave while keeping the face super clean!  Super Strong Suction Cup Attachment - Our 4.5-inch rubber suction cups won’t damage the gel coat or leave black markings on your boat. Easy to adjust on the fly, No ugly Velcro or safety tethers are required. Durable Rust-Free Materials - We Build the WakeSurf Edge with impact-resistant, lite weight glass-filled nylon 6.6. and rust-free stainless steel hardware. Our shaper is long-lasting; won’t rust or stain your boat. Built-In Flotation - Don’t worry about your wake-shaping investment sinking to the bottom. The Wakesurf Edge wing is rotomolded and sealed airtight.

9" x 18" Standard Mount Trim Tab Kit without Switch Kit- 12V Lenco Electric Standard Mount Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Kit Contents: 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads and Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner’s / installation manual All necessary stainless steel mounting hardware Specifications: Suggested Boat Length: 22' to 30' Length of Tab: 9" Width of Tab: 18" Hinge Height: 2" Minimum Transom Height: 14" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

12" x 18" Standard Mount Trim Tab Kit without Switch Kit- 12V Lenco Electric Standard Mount Trim Tab Kits make your boat ride smoother, drier, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ballscrew design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Trim Tab blades are 12 Gauge - 304 SS with a 5/8" flared trailing edge and 1/8" diameter hinge pin. Kits include standard actuators with 5/16" SS bolts. Kit Contents: 2 each of 12-gauge stainless steel trim tab blades 2 each of #15054-001 actuator with 6' leads and Deutsch plugs 2 each of #30133-103 20' actuator extension wiring harnesses 2 each of #15085-001 (116) upper mounting brackets with gland seal 2 each of #50014-001 (119) lower mounting brackets 1 each of the Lenco owner’s / installation manual All necessary stainless steel mounting hardware Specifications: Suggested Boat Length: 26' to 36' Length of Tab: 12" Width of Tab: 18" Hinge Height: 2" Minimum Transom Height: 14" Blades: 12 Gauge Stainless Steel Finish: Smooth Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Rectangular 12" x 18" Grill Cover - Pacific Blue These grill covers are designed specifically to fit any Magma rectangular grill with a 12” X 18” grilling surface and are available in boating’s most popular colors.   Constructed from breathable solution-dyed acrylic fabric that is water and fade-resistant.  The material is guaranteed with a 5-year warranty that covers the fabric from becoming unserviceable because of loss of color or strength from normal exposure conditions, including sunlight, mildew, rot, and atmospheric chemicals.  The convenient drawstring and cam-lock assembly keep it secured while underway or in windy conditions. Compatible With: Magma rectangular grill with a 12” X 18” grilling surface *Sold as an Individual 

18" Wide x 18' Long Black Carpet Roll 18" wide covers a 3x8 or a 4x8 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.1oz per square yard weight Pile height 5/32"

18" Wide x 18' Long Grey Carpet Roll 18" wide covers a 3x8 or a 4x8 board Marine grade carpet Weather resistant 100% PET polyester High quality Durable backing Minimal water retention 16.1oz per square yard weight Pile height 5/32"

3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

3 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

4 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

4 Blade aluminum propeller for Mercury 90+ horsepower outboards, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower outboards, all with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

3 Blade aluminum propeller for 90 - 300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

4 Blade aluminum propeller for 90 - 300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

3 Blade aluminum propeller for 150-300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

3 Blade aluminum propeller for 150-300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.