Heavy duty black molded plastic base. Use with SFE, AGC or MDL fuses up to 20 amps. Brass fuse clips and 8-32 terminal screws. Common bus bar connects the hot side of fuses for power feed. Bus bar has 8-32 stud terminals for main power / ground main connections. Rated 20 amps per circuit, 120 amps total for block.

Gasoline and solvent-resistant primer bulbs meet or exceed EPA/CARB Fuel Permeation Regulations. Stainless steel clamps and dual internal check valves to ensure rapid prime while preventing fuel flow back.

Prop kits containing thrust washer, spacer, nut and cotter pin.

Fits: OMC 20-35 HP 2-cyl - 1987-93. Replaces: OMC 583473, 585059. 9-tooth drive gear. Uses *DV390 replacement drive gear, *DVK90 2-piece drive kit (fits current-model starters) SR390 repair kit.*NOTE: New OMC outboard starters use a 2-piece drive assembly while older OMC outboard starters use a 1-piece drive assembly. When ordering starter drives make certain you choose the correct drive because the new and old style OMC drive assemblies are not interchangeable!

Fits: OMC 25-35 HP 3-cyl - 1997-99. Replaces: OMC 586277. 10-tooth drive gear. Uses DVK98 2-piece replacement drive kit, SR398 repair kit.

4 Blade aluminum propeller for 25-30 horsepower engines with 10 tooth spline and thru hub exhaust. 3" gear case, Japan origin.

3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.

3 Blade stainless interchangeable hub propeller for 115 and up horsepower engines with thru hub exhaust, 4-3/4" gear case. Category E prop. Requires RBX™ hub kit for installation.

3 Blade stainless propeller for Aquamatic (Long Hub) engines. AQ280 and AQ290. 17 tooth spline.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

Mercury/Mercruiser 600A type cable. Complete drop-in replacement cable for Mercury/Mercruiser engines. Stainless steel & brass fittings. Stainless cable wire.

Designed specifically to be used with late model Mercury 4000 series controls. Engineered to significantly reduce or eliminate cable "Wig-Wag", this design results in a significantly improved feel with less shifting effort. Improves the feel of the Mercury 4000 Series Controls. Nickel plated brass swivel tube.

Designed specifically to be used with late model Mercury 4000 series controls. Engineered to significantly reduce or eliminate cable "Wig-Wag", this design results in a significantly improved feel with less shifting effort. Improves the feel of the Mercury 4000 Series Controls. Nickel plated brass swivel tube.

OMC 479 type cable (1979 & later). Complete drop-in replacement cable for OMC O/B and I/O's. Stainless steel and brass fittings. 6" minimum bend radius.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.