4 Blade aluminum propeller for 9.9-20 horsepower engines with 14 tooth spline and thru hub exhaust. 2-1/2" gear case, Japan origin.

4 Blade aluminum propeller for 9.9-20 horsepower engines with 14 tooth spline and thru hub exhaust. 2-1/2" gear case, Japan origin.

3 Blade aluminum propeller for 25-30 horsepower engines with 10 tooth spline and thru hub exhaust. 3" gear case, Japan origin.

3 Blade aluminum interchangeable hub propeller for 9.9-30 horsepower engines. Category B prop. Requires RBX™ hub kit for installation.

3 Blade aluminum interchangeable hub propeller for 9.9-30 horsepower. Category B prop. Requires RBX™ hub kit for installation.

3 Blade stainless propeller for 15-35 horsepower engines with 14 tooth spline and thru hub exhaust. 3" gear case.

X-14 Heavy-Duty Cleaning Wipes *35-Pack X-14 Heavy Duty Cleaning Wipes are versatile dual-sided cleaning towels that clean heavy soils and scrub away grime. Designed to be used on hard surfaces and hands, X-14 Heavy Duty Cleaning Wipes eliminate the need to carry duplicate towel inventory in your marina, boatyard, or home. X-14 Heavy Duty Cleaning Wipes use a citrus-based formula that tackles virtually any cleaning project without leaving residue behind. The textured side loosens grease, oil, adhesive, spills, and stains. While the smooth side is ideal for a final wipe or when the texture isn’t needed.

Groco S-84-A Tie Rod, Monel .5 X 14.75  

Groco Sd-21-B Sight Glass 8.0 X 14.5  

Groco As-88-C 6 X 14.5 #316 Ss Enclosure  

18" x 14" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 22' to 42' Length of Tab: 18" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

19" x 14" Extreme Duty Performance Trim Tab Kit w/o Switch Kit- 12V- Dual Actuator Kit Lenco Electric Extreme Duty Polished Blade Trim Tab Kits feature fast response actuators for precise control. They are fully submersible and feature Plug & Play Deutsch connections. Blades are Electro-Polished 10 Gauge - 304 SS with 1" turned up edges, an 85 degree inside taper and 3/8"diameter hinge pin. Extreme Duty actuators with 3/8" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. Kit Contents: 2 each of stainless steel trim tab planes 4 each of #15056-001XD extreme duty actuators with 6" lead & Deutsch plugs Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. The following to be supplied by customer: Boat mounting hardware Actuator extension harnesses (2 for single actuator application or 4 for dual) will be required. Order the lengths of your choice. See the Lenco Accessories section. Specifications: Suggested Boat Length: 23' to 45' Length of Tab: 19" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 10 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15071-001  Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

21" x 14" High Performance Trim Tab Kit w/o Switch Kit-12V - Dual Actuator Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. Kit Contents: 2 each of stainless steel trim tab planes 4 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. The following to be supplied by customer: Boat mounting hardware supplied by customer Actuator extension harnesses (2 for single actuator application or 4 for dual) will be required. To order the lengths of your choice see the Lenco Accessories Section. Specifications: Suggested Boat Length: 24' to 42' Length of Tab: 21" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 7 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Switch Required: 15071-001 Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

25" x 14" High Performance Trim Tab Kit w/o Switch Kit-12V - Dual Actuator Lenco HP Single & Dual Actuator Electric Trim Tab Kits feature electro-polished 7 Gauge 304SS Blades & Sacrificial Anodes. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Each kit is factory assembled with extreme duty actuators with 3/8" SS bolts, a full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. Kit Contents: 2 each of stainless steel trim tab planes 4 each of #15056-001 XD extreme duty actuators with 6' lead & Deutsch plugs Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets, and 3.75" sacrificial anodes. The following to be supplied by customer: Boat mounting hardware supplied by customer Actuator extension harnesses (2 for single actuator application or 4 for dual) will be required. To order the lengths of your choice see the Lenco Accessories Section. Specifications: Suggested Boat Length: 28' to 46' Length of Tab: 25" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 7 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Switch Required: 15071-001 Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

24" x 14" Extreme Duty Performance Trim Tab Kit w/o Switch Kit- 12V- Dual Actuator Kit Lenco Electric Extreme Duty Polished Blade Trim Tab Kits feature fast response actuators for precise control. They are fully submersible and feature Plug & Play Deutsch connections. Blades are Electro-Polished 10 Gauge - 304 SS with 1" turned up edges, an 85 degree inside taper and 3/8"diameter hinge pin. Extreme Duty actuators with 3/8" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. Kit Contents: 2 each of stainless steel trim tab planes 4 each of #15056-001XD extreme duty actuators with 6" lead & Deutsch plugs Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. The following to be supplied by customer: Boat mounting hardware Actuator extension harnesses (2 for single actuator application or 4 for dual) will be required. Order the lengths of your choice. See the Lenco Accessories section. Specifications: Suggested Boat Length: 25' to 50' Length of Tab: 24" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 10 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15071-001  Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.