 |
Standard Zinc Trim Tab Anode for 25-50 HP Mercury Engines
Tecnoseal Zinc Anode for Mercury Outboard & Mercruiser Sterndrive and engines. For Trim Tab. Fits Mercury 25-50 Hp F25, F30, F40 and F50 outboards (1998 and later). Mercury Part: 822157-C2. For use in Salt water.
|
11.35 |
|
 |
Standard Aluminum Trim Tab Anode for 25-50 HP Mercury Engines
Tecnoseal Aluminum Anode for Mercury Outboard & Mercruiser Sterndrive and engines. For Trim Tab. Fits Mercury 25-50 Hp F25, F30, F40 and F50 outboards (1998 and later). Mercury Part: 822157-C2. For use in Salt water.
|
6.41 |
|
 |
Fits: OMC 8/9.9-11 HP, 4 stroke - 1997-98; 9.9-15 HP - 1977-92. Replaces: O.M.C. 386430. 10-tooth drive gear. Uses DV369 replacement drive gear, SR369 repair kit.
|
168.67 |
|
 |
Fits: OMC 90-115 HP 60 Deg V4, - 1997-up, 80-100 Hp 1998-2000; 100 HP Commercial - 1997; 80 HP Jet - 1998. Replaces: OMC 584980, 586284. Uses 9 tooth drive gear DV517, jackshift assembly JSA517, SR399 repair kit.
|
212.10 |
|
 |
Fits: OMC 9.9-15 HP - 1993-UP. Replaces: O.M.C. 586274. Uses small 10-tooth drive gear DV361, brush holder SR361.
|
205.39 |
|
 |
Fits: OMC - 1997-Up 9.9/15 HP, 4-stroke. Replaces: O.M.C. 584608. 10-tooth drive gear. Uses DVK68 2-piece drive kit, SR368 repair kit.
|
174.20 |
|
 |
Fits: O.M.C. V4 and V6 (1997-Up 75/90/115 HP; 2003 90/105/115 Hp; 2003 60 HP). Replaces: O.M.C. 586287, 438878. Uses 9 tooth drive gear DV517 or 10 tooth drive gear DV518. Replacement jack shaft 9 tooth assembly JSA517, 10 tooth assembly JSA518. SR363 brush repair kit.
|
161.32 |
|
 |
35 amp stators for 4, 6 and 8 cylinder engines.
|
477.40 |
|
 |
Heavy-duty trim/tilt motor only. Fits: 1997-UP 115 HP, 2000-UP 115 HP 4-Stroke, 1997-2000 130 HP, 1997-UP 150-200 HP, 1998-UP 225 HP. 2-wire connection, 4 bolt mount, ring terminal ends. Includes O-ring.
|
335.10 |
|
 |
Engine end connection kits for 1973-1978 OMC O.E.M (400 type) cables with bare wire ends. Note: included clip is not used on stern drives.
|
33.79 |
|
 |
Fits: OMC 1989-92 M-suffix 40, 48, 50 HP. 2-wire connection with female spade terminal ends. Includes O-ring hollow-hex shaft. 4-bolt mount.
|
241.70 |
|
 |
Adaptor tool for installing gimbal bearing. Must use with alignment tool 18-4442 to install gimbal bearing. Fits Mercruiser, OMC, Volvo Penta.
|
72.79 |
|
 |
High torque, permanent magnet, gear reduction starter for Mercruiser, OMC and Volvo. 1.7KW starter will replace 9 tooth drive OEM versions for 3.0-8.1L with 14" flywheel. Clockwise rotation, staggard bolt pattern. Mounting bolts included. Uses SW450 solenoid, MBK450 bolt kit (included) and BH450 brush holder.
|
253.50 |
|
 |
Replacement relay, OMC, 12 Volt, 30 Amp.
|
21.65 |
|
 |
35 amp stators for 4, 6 and 8 cylinder engines.
|
481.88 |
|
