|
Universal Fuel Line Kit - 5/16" Diameter x 6' Length
This EPA-certified Attwood Universal Fuel Line Kit reliably delivers fuel to your engine and provides the ultimate in performance, safety, and value. The kit includes a 6-foot-long, 5/16-inch diameter low-permeation fuel line that is designed to prevent kinking and hardening, and is rated up to 100 degrees C. There’s also a multi-layer, low-permeation primer bulb with connections engineered for strength, durability, and leak resistance.
Features:
This Fuel Line Kit is compatible with Ethanol blended fuels and with all OEM-brand engines.
Universal for any engines and tanks
Multi-Layer, Low-Permeation Primer Bulb
6 ft. x 5/16 in. Low Permeation Hose
Reliably delivers fuel to your engine
*No end fittings included
|
41.39 |
|
|
Drain Plug And Receiver Kit - 3/4" Diameter
The Attwood Drain Plug and Receiver Kit ensures that a drain is closed properly.
Features:
Molded black plastic with threaded receiver
Molded retaining strap
Includes attaching screws and elastomeric gasket for a watertight fit
Specifications:
Diameter: (inch) 3/4"
*Intended for use on small recreational boats and jet skis
|
5.48 |
|
|
Yamaha Fuel Line Kit 6' x 3/8"
Attwood's low-permeation fuel line kits set the standard in performance, safety, and value. Along with featuring Attwood's award-winning Universal Sprayless Connector, these kits meet strict United States EPA regulations. Attwood Corporation has been an award-winning leader in engineering, testing, and manufacturing the highest quality marine products for over 100 years. We deliver safe and reliable lighting, fuel systems, water systems, seating & pedestals, swim ladders, custom upholstery, and general marine accessories that are easy to install and meet regulatory compliance.
Features:
Includes Attwood's award-winning Universal Sprayless Connector; no more dangerous fuel sprays when connecting and disconnecting pressurized lines
Multi-layer low-permeation primer bulb with 60% more fuel output compared to competitors
Includes 3/8-inch low-permeation fuel hose that resists kinking and hardening; rated up to 100 degrees Centigrade
Versatile: compatible with Ethanol blended fuels, Yamaha Brand engines and tanks
Attwood products are both compatible and reliable, engineered and built with a never-fail attitude
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
46.14 |
|
|
Universal Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb
This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line.
Features:
Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels
Specifications:
Material Construction: Aluminum
Male thread, hose barb
(inch) Male 3/8" NPT x 3/8" Barb
*Use thread sealant on all threads
|
4.25 |
|
|
Aluminum Fuel Hose Fitting - 3/8" NPT x 3/8" Barb - (Anti-Siphon Valve)
This Attwood Fuel Tank Fitting is a dependable replacement for original equipment and provides a sure connection in a fuel line. This is a male thread, anti-siphon valve with 3/8-In. NPT x 3/8-In. barb.
Features:
Fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels
Anti-Siphon Valve
Material Construction: Aluminum
Male thread, hose barb
(inch) Male 3/8" NPT x 3/8" Barb
*Use thread sealant on all threads
|
18.46 |
|
|
Outboard Fuel Filter for 3/8 inch Lines
Protect your carbureted engine by trapping pollutants before they even reach the engine itself. High-flow, in-line fuel filters will work with most outboard motors.
Features:
Use with 3/8 inch fuel lines
Works with most outboard motors
A clear body allows visual inspection, making it easier to stay on top of maintenance
High-strength, impact-resistant, and shatter-resistant construction is ideal for tough conditions
Disposable for ultimate convenience
*Best to replace during winterize or spring start-up for optimum results
|
3.50 |
|
|
OC15109-6 Steering Cable
8" Stroke x 6' long
For use with Type R Remote Drive Unit
|
152.71 |
|
|
Male Run T-Fitting - 3/8" x 3/8" Tube x 1/4" NPT
Typical Application:
Used to connect any 1/4 NPT Female port to our hoses
Specifications:
1/4 NPT to 3/8 COMP FITTING
Helm side = 1/4 NPT
Hose side= 9/16 - 24 UNEF 2A
|
32.48 |
|
|
8" ID x 6' Long Silicone Marine Wet Exhaust & Water Hose - Blue
Trident Silicone Marine Wet Exhaust and Water-Coolant Hose is the ultimate in extra thick soft wall silicone quality with very high-temperature performance and extra long service life. Exceeds SAE J2006-R1, and ABYC & NMMA P-1 exhaust standards. #202V Glossy Blue “Very Hi Temp” has 4-6 ply polyester reinforcement and 350°F (177°C) Max. Used worldwide on premium boats, yachts, and special service vessels. It has become the super yacht standard.
|
703.52 |
|
|
Flojet 01740-003S Strainer 3/8" Barb X 3/8" Barb
Flojet Strainer with 3/8” Hose Barb Inlet and 3/8” Hose Barb Outlet, In-Line Design, Fine 40 Mesh Stainless Steel Screen
Strainers for In-Line Applications. FDA Approved for Potable / Drinking Water.
Strainer Body made of Polypropylene with Clear Polysulfane Cap and Buna-N FDA O-Rings.
Suitable for Fresh or Salt Water use.
Easily Cleaned with See Through Thread-On Cap.
Course 20 Mesh Screens are typically used for Washdown, Bilge and Toilet Rinse Applications.
Fine 40 Mesh Screens are typically used for Potable / Drinking Water Applications.
Maximum Flow Rates:
With 3/4" Hose Barb Fittings: 7.0 GPM (27 LPM)
With 1/2" Hose Barb Fittings: 4.0 GPM (15 LPM)
With 3/8" Hose Barb Fittings: 2.1 GPM (8 LPM)
Maximum Water Temperature: 160F (70C)
Maximum Pressure: 70 PSI (5 bar)
The Strainers that are Equiped with a "Direct Plug-In Quad Port" will fit into the Snap-In Quad Ports on Flojet Diaphragm Pumps and Jabsco Diaphragm Pumps sized under 6 GPM.
|
28.55 |
|
|
Wire Rope Grip - Size 10 - 10mm(3/8") Diameter Wire
Features:
Used when adjustment in strop length is needed
Stainless Steel
Require no special tools for assembly and can be disassembled and reused
|
11.32 |
|
|
Leather Mooring Line Chafe Kit - 3/8" & 7/16"
Mooring line chafe kits include: Waxed twine, heavy duty needle and (2) 10” pieces of leather pre-stamped for sewing. Used to reduce chafe and extend the life of mooring lines. Natural leather - color may vary.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
10.22 |
|
|
Impeller Kit - 9 Blade - Nitrile - 3-3/4" Diameter x 3-1/2" W, 1" Shaft Diameter
Features:
Material: Nitrile
Drive Type: Spline Drive
Number of Blades: 9
Dimensions: Diameter: 3-3/4", Shaft Diameter: 1", Shaft Width: 3-1/2"
Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps.
Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance.
Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance.
Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces.
Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such.
Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
189.23 |
|
|
Split Ring - 10mm(3/8") Diameter
Suits Clevis Pins RF258-RF266
|
0.86 |
|
|
Swivel Shackle - 5/16" Pin - 2-3/8"L x 21/32"W
Features:
Coined head pin 7.9mm(5/16") Diameter Pin
Grade 316 Stainless Steel bodies and pins
Stainless Steel ball bearing race
|
33.11 |
|