B60-12 12° Tilted Element Transducer with 6-Pin The bronze B60-12° provide a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull. Features: Depth/Temp 50/200 kHz 600w RMS Mid-performance Bronze WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

xSonic B150M Thru-Hull Transducer - 9-Pin 10M Cable - 0° As CHIRP continues to redefine recreational fishing, AIRMAR has expanded the lineup of broadband transducers to satisfy the growing demand for this game changing technology. The B150M economical CHIRP transducers designed for offshore fishing and freshwater anglers. Operating at a frequency range of 95-155 kHz, these transducers reveal fish in shallow, murky waters at medium depths (up to 2,500 feet*) along with ultra-clear target resolution.  *Depths vary depending on target strength and sea conditions  A tilted element model in the CHIRP Thru-Hull product line, the B150M CHIRPS across the following bandwidth: M Model - Medium Frequency 95-155 kHz    Features: Depth and water temperature sensor 300W Bronze Thru Hull 0° tilt Ideal for inshore or coastal fishing in shallow to medium depths Freshwater anglers will see fish holding close to structures and suspended fish  Track bottom at higher boat speeds More coverage under your boat delivers wider archesand 26° to 17° beamwidths  Cover the medium frequency range-CHIRPs from 95-155kHz to provide 60 kHz of total bandwidth from one transducer Hull Type: Fiberglass, wood 1 internal ceramic

xSonic SS60 Stainless Steel 20° Tilt Thru-Hull Depth/Temp Transducer - 9-Pin - 10M Cable The SS60 is a stainless steel, thru-hull, tilted, dual-frequency, depth and temperature transducer. The ceramic element is tilted for built-in deadrise compensation, giving excellent echo returns for more accurate depth readings. Features: Depth/Temperature - Calculates how deep the water is, so that you can avoid running aground, whilst also incorporating a temperature sensor for accurate water temperature readings Easy To Install Dual Frequency - Works at 50 kHz and 200 kHz for good target detail in shallow water and excellent bottom tracking in deep water Highly Accurate - Provides extremely accurate data 20° Tilt - The 20° tilt is ideal for boats with a 16° to 24° hull deadrise Low Profile - The low profile housing minimizes drag with just 5mm extending outside of the hull Plug & Play Connection - Easily connect to NSSevo3, Lowrance HDS G3

B164 1kW Tilted Element 20° - 8-Pin Garmin's bronze, thru-hull mount transducer with 20° tilt provides depth and temperature data. Garmin's transducer has an operating frequency of 50 or 200 kHz and mounts on a 16-24° deadrise angle. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

xSonic TM150M Transom Mount Transducer - 9-Pin 10M Cable As CHIRP continues to re-define recreational fishing, AIRMAR has expanded the lineup of broadband transducers to satisfy the growing demand for this game changing technology. The TM150M economical CHIRP transducers designed for offshore fishing and freshwater anglers. Operating at a frequency range of 95-155 kHz, these transducers reveal fish in shallow, murky waters at medium depths (up to 2,500 feet*) along with ultra-clear target resolution. *Depths vary depending on target strength and sea conditions  This is a Transom Mount model in the CHIRP product line. The TM150M is an excellent choice for freshwater fishers, and CHIRPS across the following bandwidth: Medium Frequency 95-155 kHz. Designed for smaller boats up to 25'.   Features:  Depth and water temperature sensor 300W Plastic Housing Ideal for inshore or coastal fishing in shallow to medium depths Freshwater anglers will see fish holding close to structures and suspended fish Track bottom at higher boat speeds More coverage under your boat delivers wider archesand 26° to 17° beamwidths Cover the medium frequency range-CHIRPs from 95-155kHz to provide 60 kHz of total bandwidth from one transducer Hull Type: Fiberglass, wood or metal 1 internal ceramic

xSonic TM185HW Wide-Beam Chirp Tramsom Mount Transducer - 9-Pin Get more coverage under the boat with Airmar's new wide beam Chirp product line. Offering a high frequency range of 150-250 kHz and a constant 25° Beamwidth, these transducers are truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers A unique property of the new high frequency transducers is that the Beamwidth is a constant 25° angle across the entire frequency band. Now, in addition to providing vast bottom coverage and precise fish detection in the upper water column that can sometimes go unseen with our narrow beam transducers, Airmar's new wide beam format also creates crisper and larger return images on the display. We've got you covered. Features: Depth & temperature 150-250 kHz H frequency Urethane Housing 1 kW Wide 25° beam Weight: 0.45 kg (1.1 lb) Hull Deadrise: 2° to 20° Acoustic Window: Urethane

B175L Bronze Low Profile Thru Hull 20° Tilted Element Transducer 1kW Features Material: Bronze For use with CP450C or CP470 Chirp Sonar Module Power (RMS): 1Kw Max Depth(ft): 2,500 Frequency (khZ): 40-60 Beam Width(L/H): 32°-21° Records: Depth / Temperature Approved Hull Material: Fiberglass / Wood Cable Length (Ft/M): 33ft / 10M Supported Deadrise / Transom Angles: 16-24° Deadrise Note: Using a Single B175 or B75 requires the A80328 Single Operation Cable

xSonic P79 Adjustable 200/50kHz Plastic In-Hull Transducer - 9-Pin This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap. The 9-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise. Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat. *Fiberglass should be no more than 5/8" thick *Not recommended for cored hulls

xSonic M135M Medium Chirp 1 kW In-Hull Transducer - 9-Pin The M135M’s medium frequency delivers the right combination of coverage under the boat, an extended depth range, and the ability to produce clean and accurate target and structure returns in mid- to deeper water. Medium frequency also delivers excellent shallow to mid-depth performance, bottom detail, and fish-target separation. Operating at a frequency range of 85 to 135 kHz, this transducer reveals fish at medium depths up to 457 m (1500 ft) and gives ultra-clear target resolution. Airmar’s M135M includes a plastic mounting base that is aligned with the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. The eco-friendly coolant is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is that there are no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 11 m (36') with a solid fiberglass hull. Features: Depth only 1 kW of power 50 kHz of total bandwidth from one transducer Recommended for use on planing and displacement hulls Plastic transducer and mounting base Covers popular fishing frequencies of 88 and 107 kHz plus everything else in the bandwidth Also available as transom (TM185M), thru-hull low-profile (B175M), and thru-hull with fairing (B285M) mounts Patented Xducer ID® technology Specifications: Medium frequency: 85 to 135 kHz Beamwidth: 16 degrees to 11 degrees Maximum Depth: 457 m (1500 ft.) Weight: 4.2 kg (9.2 lb.) Recommended Boat Length: Up to 11 m (36 ft.) Hull Material: Solid fiberglass only Hull Deadrise: Up to 22 degrees Acoustic Window: Urethane Transducer Element: One broadband ceramic assembly Includes: Adjustable mounting base This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Navico Mix & Match Cable for Low-Frequency CHIRP Transducers - 9-Pin Specifically for use with Airmar's Mix and Match CHIRP transducers up to 1kW (1,000W). This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B60 600W Tilted Element 12° - 8-Pin This entry-level tilted bronze transducer accommodates deadrise angles of 8 to 15 degrees without a fairing. An excellent choice for fiberglass and wood hulls, this 600W 8-pin transducer has a depth of 800' to 1,200'; an operating frequency of 50 to 200 kHz; and a beamwidth of 45 to 12 degrees. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. *Do not use on metal hulls. When using with a 6-pin Garmin sounder, a transducer adapter cable is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B60-20 20° Tilted Element Transducer with 6-Pin The bronze B60-20° provide a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull. Features: Depth/Temp 50/200 kHz 600w RMS Mid-performance Bronze WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

B60 Tilted Element™ 12° 12° titled version is designed for 8° - 15° deadrise angles The bronze B60-12° provide a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull. Features: Depth/Temp 50/200 kHz 600w RMS Mid-performance Bronze WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

B-60-20 Tilted Element Transducer Low profile tilted element for 16° to 20° deadrise hulls. Features: 600 Watts Dual 50/200kHz

B-60-12 Tilted Element Transducer Low profile tilted element for 8° to 15° deadrise hulls. Features: 600 Watts Dual 50/200kHz