Installation Kit for Deep-Pipe Level Sensors Replacement kit for parts sold with Deep-Pipe Level Sensors. In the Box: Stainless Steel Top Flange Bottom Threaded Flange Rubber Gasket x 2 Washers x 5 Screws x 5 *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Sealing Kit for Water Level Sensors Replacement kit for water sensors. In the Box: Gaskets x 2 Allen bolts Allen key *Sold as an Individual  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Fluid Pressure Monitor Maretron's Fluid Pressure Monitor is used to adapt up to six pressure transducers to the NMEA 2000® network (pressure transducers sold separately). This allows you to observe fluid pressures and tank levels anywhere on the vessel where there are NMEA 2000® compatible displays. With the appropriate transducer, the FPM100 reports either pressure or vacuum for a variety of applications including water pressures, oil pressures, hydraulic pressures, or system vacuum for detecting clogged filters. The FPM100 also has a tank level mode, so that fluid levels in a tank can be monitored via a pressure transducer mounted at the bottom of the tank and transmitted over the NMEA 2000® network. This allows you to monitor the fluid levels in tanks that are extremely deep, have internal structures, or are otherwise not suited for other tank level sensing technologies. In this mode, the FPM100 can be calibrated for irregular tank shapes so that you know the true level of the tanks. The FPM100 is NMEA 2000® certified so you can view any and all information anywhere on the vessel using a compatible NMEA 2000® display. The FPM100 is a key component of Maretron's N2KView® vessel monitoring and control system. Features: Adapts up to six pressure transducers to the NMEA 2000® network Each channel independently programmed to match pressure transducer characteristics Each channel independently programmed in pressure/vacuum mode or tank level mode In Tank Level Mode, measures levels of extremely deep or irregularly shaped tanks Applications Water Pressure Atmospheric Pressure Compressed Air Pressure Hydraulic Pressure Steam Pressure User Defined Pressure Sources Fuel Tank Level/Volume Remaining Fresh Water Tank Level/Volume Remaining Waste Water Tank Level/Volume Remaining WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

GX Tank 140 Tank Monitoring for 4-20 MA, 1-10VDC Sensors - Monitors Up to 4 Sensors *Sensor Not Included The GX Tank 140 takes readings from up to four tank level sensors. It is an accessory for our range of GX system monitoring products, of which the Cerbo GX is the most commonly used model. Tank levels can be read out locally in the system, see screenshot, as well remotely through our VRM Portal. The GX Tank is compatible with current senders (4 to 20 mA) as well as voltage senders (0 to 10 V). The connection to the GX Device is via USB, which is also how the GX Tank is powered: no additional power wires are required. Tank sender wiring is kept as simple as possible: two of the four inputs provide a 24 V power supply, to power the sender. The other two channels do require an external power supply, and there is power in the terminal together with fused outputs to facilitate that. Upper and lower limits are configurable, to allow using senders that provide only part of the scale, for example, 0 to 5 V. To provide a stable reading, the readings are averaged damping. The damping can be configured between 1 and 60 seconds. Faulty sensors and wiring issues are detected: an alarm will be raised when values are out of range. For marine applications, the GX Device can transmit these tank levels on the NMEA 2000 network to be picked up by other displays such as an MFD. Please contact your dealer for any returns, repairs or support issues related to this product.

Fluid Reservoir This reservoir is meant for holding hydraulic pump fluid. How to Use: Periodically, check the fluid level in HPU With the trim tabs completely retracted, the fluid level should be about 2" from the bottom of the reservoir (approximately 22 ounces) refill, remove the Lexan cover and filler plug located at the front left-hand corner of the reservoir Fill with any type of automatic transmission fluid (ATF) only Brands running HPU with excess or a lack of fluid will not cause damage to the trim tab system This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 150mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 150 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 600mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 600 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 160mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 160 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 170mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 170 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 180mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 180 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 190mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 190 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 200mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 200 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 210mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 210 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 220mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 220 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Deep-Pipe Level Sender - 230mm - 0 to 180 OHM Deep-Pipe Level Sensor is ideal for usage in fuel tanks. Its 38 mm diameter vertical tube contains a float inside, which measures a level of the liquid. Small holes at the top and bottom of the tube act as a baffle to fuel sloshing around in the fuel tank, so the float position remains stable at any sea state.  Sensors are made in various lengths starting at 150 mm increasing to 1200 mm – please ensure that the length chosen is at least 4 mm from the base of the fuel tank once fitted.  Features: Tubular Sensor Stainless Steel Suitable for Fuel (Oi -Petroleum-Diesel-Gasoline) and Water Length: 230 mm Technical Specifications: TE Superseal Connector 2-Pole IP67 Operating Temp.: -25°C to 65°C or -13°F to 149°F Operating Voltage: 6 to 24 VDC Compensation chamber Flange: 5-Hole SAE Flange 54mm PA66 GF30 Wiring harness with length of 200 mm Signal ranges: 0 to 180 OHM IP67 protection rating Communication: Analog In the Box: Deep-Pipe Level Sensor Installation Kit Safety Instructions Installation Instructions *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.