4 Blade stainless propeller for 25-30 horsepower engines with 10 tooth spline and thru hub exhaust. 3" gear case, Japan origin.

Deluxe trailer jack with 1500 lb. capacity and 10" travel. Fits trailer tongues up to 3" x 5". Swivel plate and caster designed to OE specifications. Extra bushing installed for smooth handle cranking. 6" spoked wheel. Quickly pivots to horizontal position. Black textured finish over zinc plated coating. Grease port fitting for easy lubrication. Mounting hardware included.

2301 150AMP Common BusBar 10 x #8-32 Screw Terminal  Features: Stud design provides direct terminal to bus contact for low resistant connection Stainless steel studs and screws allow high torquing for excellent electrical contact Tin-plated copper bus for maximum conductivity and resistance to corrosion UL 94-VO rated (self extinguishing) base material resists high heat Raised bus provides easy access to multiple wires on a single screw UL 94-VO rated base material resists high heat Captive star type lock washers for anti-rotation and eliminate handling of small, easily dropped parts WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

2702 DualBus 100AMP Common BusBar 10 x 8-32 Screw Terminal Features: Combines negative and positive buses on one block Tin-Plated Copper CDA 110 / UNS 11000 UL 94-V0 Rated, Glass Reinforced Thermoplastics #8-32 Screw 10 per bus Maximum Voltage: 300V AC / 48V DC WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

10" x 8" Trim Tab Set Features: Wiring - Color-coded wiring in 25' to 40' lengths with quick connects fittings, meets federal standards for heat, pull, and insulation, making installation easy. Solenoids - They are custom designed for Insta-Trim Boat Leveler Co., epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb-type hose fittings provide tight, secure connections. Motor - A powerhouse with coated wirings and a thermal overload that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminated oil leakage. The motor is mounted with stainless steel nuts and bolts and is easily disassembled. Brackets - Swivel-type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins it tab strikes an object. Pump - Designed and engineered exclusively by Instatrim. The built-in bypass is factory set at 400 P.S.I. tolerance held to .00025. Amperage doesn't exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure. Motor Cover - 4 1/2" D x 6" W x 11"H, high impact ABS plastic cover with a built-in oil reservoir mounts easily with two screws. The filler is located in front. Our cover protects the motor from occasional wash down. Cylinders - Impact-resistant, fiberglass-reinforced nylon cylinders eliminate expansion and resist ultra-violet rays. Two expanding type seals, plus O-ring, eliminate high and low-pressure leaks. Barbed cylinder fitting and an inserted tubular rod prevent hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion. Trim Tabs - 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim's hinges prevent most spray and can be used for transom or bottom mounting. Hose - Designed and manufactured exclusively for Insta-Trim with nylon-reinforced webbing and protective PVC coating. Rated at 2000 lb. burst pressure, 15' of hose is supplied for your system. Entering the transom 6" above the water line, the hoses are held securely with hose trim. Stainless steel clamps hold the hose to barb fitting at the solenoid. Rocker Type Controls - Mounted on the dash they are easy to operate. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.

2300 150AMP Common BusBar 10 x #8-32 Screw Terminal with Cover Features: Stud design provides direct terminal to bus contact for low resistant connection Stainless steel studs and screws allow high torquing for excellent electrical contact Tin-plated copper bus for maximum conductivity and resistance to corrosion UL 94-VO rated (self extinguishing) base material resists high heat Press on insulating cover attaches to studs and allows unobstructed wire access Raised bus provides easy access to multiple wires on a single screw WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Trim Plane Assembly 10" x 12" for M120 Bennett trim planes are made of high-quality 304 stainless steel and remain strong and rigid, even in the most challenging situations. Each trim plane assembly includes a trim plane, backing plate and hinge for one side of the boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

1.25" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

1.5" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

2.25" Tall Stainless Stud w/#10 x 24 Thread Utilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter. These studs can be bonded from either surface of the base plate.

.75" Tall Stainless Standoff w/#10 x 24 Threads - Through-Thread Unlike the SOB standoffs which have a blind thread, the SOT series standoffs have a thread which runs all the way through the barrel of the standoff. This allows the standoff to be mounted from either side of the base. These parts are manufactured in 316 stainless steel making them suitable for deck applications. This standoff is inertial (friction) welded to the base yielding a very strong part. The bases are all 1.25" in diameter. Use for through deck mounting of hardware or anywhere you need a fixed female thread.

Insta-Trim 10" x 10" Trim Tab Set Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features: Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation. Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections. Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied. Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure. Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object. Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion. Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting. Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down. Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection. Rocker type controls: Mounted on the dash, they are easy to operate. Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.

Flex Keel Pad - Edge Cover Style - 10" x 1-1/2" - Black These black poly pads cushion the trailer cross members to protect your boat keel. Edge cover style mounts on the trailing edge of any width cross member or axle. Features: Black poly material 10" L x 1-1/2" W 3/8" thick 4-1/2" hole centers Mount using two rivets or screws through the top (hardware not included).

HTM-3 - 10" x 30" - Single Layer - Black Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs. They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.

HTM-3 - 10" x 30" - Single Layer - Navy Master Fender Covers are specially designed to protect the topsides and hull from fender scuff and reduce the need for expensive gel coat repairs. They are made from a premium stain resistant, non-abrasive, loop-knit acrylic fabric, which is both durable and fade resistant. They are available in a variety of colors and sizes to suit your individual requirements.