3 Blade stainless propeller for Mercury 90+ horsepower outboard engines, select Mercruiser stern drive engines and Honda/Nissan/Tohatsu 115-250 horsepower engines. All with 15 tooth spline and thru hub exhaust. 4-3/4" gear case.

3 Blade stainless propeller for 90 - 300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear case.

3 Blade stainless propeller for 150-300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

3 Blade stainless propeller for 150-300 horsepower engines with 15 tooth spline and thru hub exhaust. 4-3/4" Gear Case.

3 Blade stainless propeller for engines with 19 tooth spline.

3 Blade stainless propeller for engines with 19 tooth spline.

3 and 4 Blade aluminum propeller for Volvo Penta DP280, DP290. Front propeller is 27 tooth spline. Rear Propeller is 19 tooth spline.

.75" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a .75" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

1" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

1.25" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.25" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

1.5" Tall Stainless Stud w/#8 x 32 Thread Our Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide range of wire clamps and other small components to composite surfaces. The base plate is 0.62" in diameter with a 1.5" tall stud. Tensile strength is 300 lbs. and shear strength is 375 lbs. Maximum torque load is 45 inch/lbs.

2" Tall Stainless Stud w/3/8" x 16 Thread The HS200 stud is designed for heavy load applications such as mounting filters and panels. Thestud is inertial (friction) welded to a 2" base plate creating a very strong part. Manufactured of 304 stainless steel. Tensile strength is approximately 1,200 lbs. and shear strength is 1,500 lbs.

Designed specifically to be used with late model Mercury 4000 series controls. Engineered to significantly reduce or eliminate cable "Wig-Wag", this design results in a significantly improved feel with less shifting effort. Improves the feel of the Mercury 4000 Series Controls. Nickel plated brass swivel tube.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

3 Blade stainless interchangeable hub propeller for 40-140 horsepower engines with thru hub exhaust, 4-1/4" gear case. Category D prop. Requires RBX™ hub kit for installation.