|
Chesapeake Black SS 4" Tachometer w/Systemcheck Indicator - 7000 RPM (Gas) (Johnson / Evinrude Outboard)
Perimeter-lighted Black dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
SystemCheck Warnings
No Oil
Engine Overheat
Check Engine
Low Oil
4" - Hole size: 3.375" (85mm)
For Engine Types:
(Johnson / Evinrude Outboard)
Specifications:
Anti-scratch glass lens
Perimeter lighted back light
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9884
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
202.38 |
|
|
Chesapeake White SS 4" Tachometer w/Systemcheck Indicator - 7000 RPM (Gas - Johnson/Evinrude Outboard)
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
SystemCheck Warnings:
No Oil
Engine Overheat
Check Engine
Low Oil
4" - Hole size: 3.375" (85mm)
For Engine Types:
Johnson/Evinrude Outboard
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9881
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
202.38 |
|
|
Dress White 4" Tachometer w/Systemcheck Indicator - 7000 RPM (Gas) (Johnson /Evinrude Outboard)
Perimeter-lighted White dial with bold Black graphics, White aluminum bezel, contoured Black pointer and flat glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
4" - Hole size: 3.375" (85mm)
SystemCheck Warnings
No Oil
Engine Overheat
Check Engine
Low Oil
For Engine Types:
(Johnson/Evinrude Outboard)
Specifications:
Anti-scratch glass lens
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N TC9887
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
179.22 |
|
|
Euro Black 2" Trim Gauge f/ Johnson/Evinrude/Suzuki Outboard
Perimeter-lighted Black dial with bold White graphics, Black aluminum bezel, contoured White pointer and flat glass lens.
2"- Hole Size: 2.0625" (53mm)
For Engine Types:
Johnson/Evinrude/Suzuki Outboards
Specifications:
Anti-scratch glass lens
12 VDC negative ground
Perimeter-lighted Black dial
Can be adapted for 24 VDC systems
Factory P/N GP9305
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
25.80 |
|
|
Euro White 2" Trim Gauge f/ Johnson/Evinrude/Suzuki (Outboard)
Perimeter-lighted White dial with bold Black graphics, Black aluminum bezel, contoured White pointer and flat glass lens.
2"- Hole Size: 2.0625" (53mm)
For Engine Types:
Johnson/Evinrude/Suzuki Outboards
Specifications:
Anti-scratch glass lens
Perimeter-lighted White dial
12 VDC negative ground
Can be adapted for 24 VDC systems
Factory P/N GP9708
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
25.80 |
|
|
2" Trim Gauge f/Johnson, Evinrude & Suzuki Outboards
Faria Beede’s Platinum Series Instruments feature spun aluminum gauge dials with custom graphics and a polished stainless steel bezel providing a rugged, elegant look.
All Platinum Series gauges feature Faria's revolutionary domed glass Fog-Resistant lens. These lenses shed condensation and resists scratching and other types of fouling common in the marine environment.
2"- Hole Size: 2.0625" (53mm)
For Engine Types:
Johnson, Evinrude & Suzuki Outboards
Specifications:
Domed Glass Anti-fog, Scratch Resistant Lens
Stainless Steel Bezel
Blue LED Illuminating around the Perimeter of the Dial
Illuminated Backlit Fire-Orange Tip Pointer
Factory P/N GP5087
*Sold as an Individual
*Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
45.59 |
|
|
Coral 2" Trim Gauge for Suzuki, Johnson & Evinrude Outboard
Perimeter-lighted Black dial with stylish White and Blue graphics, Black aluminum bezel with burnished leading edge, contoured White pointer, and flat glass lens.
2" - Hole Size: 2.0625" (53mm)
For Engine Types:
Johnson/Evinrude/Suzuki Outboards
Specifications:
Scratch Resistant Lens
Black Aluminum Bezel
Contoured White Pointer
Factory P/N GP9273
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
27.28 |
|
|
Johnson/Evinrude Outboard Relay - 12V 30A
Johnson/Evinrude outboard relay that will fit BRP-OMC.
Replaces:
BRP-OMC 582195
BRP-OMC 582472
BRP-OMC 582473
BRP-OMC 584416
BRP-OMC 586147
BRP-OMC 586244
BRP-OMC 3857533
BRP-OMC 586224
SIERRA 18-5705
*ARCO Assurance 12-month part and labor warranty protection
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
16.46 |
|
|
Johnson/Evinrude/OMC (Outboard Marine Corporation) Male Tank Fitting - 1/4" NPT
This Attwood male tank fitting is suitable for use with leaded, unleaded, ethanol-blended, and alcohol-blended fuels. The threaded fitting has a 1/4" male NPT thread and uses thread sealant on all threads. Clamps are not included.
Features:
Johnson, Evinrude, and OMC fitting
Quick-connect ¼-inch male thread makes installation easy
Solid machined brass for dependable performance, peace of mind
*Specifically mates to Attwood part numbers: 8889LP6 & 88FHE516-6
|
7.40 |
|
|
Johnson/Evinrude/OMC (Outboard Marine Corporation) Female Hose Fitting - Tank Or Engine End - 5/16" Barb
For use on both ends of the fuel line to connect tank fitting and motor. The hose barb fits a 5/16" inner diameter hose.
Features:
Johnson, Evinrude, and OMC fitting
Tank or Engine End
Material Construction: Acetal
*Specifically mates to Attwood part number: 8883-6
|
5.69 |
|
|
Johnson/Evinrude/OMC (Outboard Marine Corporation) Female Hose Fitting - Tank Or Engine End - 3/8" Barb
For use on both ends of the fuel line to connect tank fitting and motor. The hose barb fits a 5/16" inner diameter hose.
Features:
Johnson, Evinrude, and OMC fitting
Tank or Engine End
Material Construction: Acetal
*Specifically mates to Attwood part number: 8883-6
|
4.64 |
|
|
Euro Black 4" Tachometer w/Systemcheck 7000 RPM (Gas) f/ Johnson / Evinrude Outboard)
Perimeter-lighted Black dial with bold White graphics, Black aluminum bezel, contoured White pointer and flat glass lens.
Electronic tachometers work by counting pulses generated by the ingition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed above.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
4" - Hole size: 3.375" (85mm)
For Engine Types:
Johnson and Envinrude Outboard
SystemCheck Warnings:
No Oil
Engine Overheat
Check Engine
Low Oil
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
Perimeter-lighted Black dial
Can be adapted for 24 VDC systems
Factory P/N TC9951
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
154.78 |
|
|
MACH™ Series High Efficiency & Flexibility Engine Control Cable - Johnson/Evinrude/OMC - 30'
MACH14 - Current BRP® (OMC®) style (like C14)
MACH14 Stroke: 75 mm (3”). For BRP® - Evinrude® (OMC®) engines manufactured from 1979 to date. Blue color jacket designed for high performance applications
For the ultimate in efficiency and response, the Mach Series cables deliver unmatched results. They have been specifically designed to make even the most complex of cable installations result in smooth, easy and precise shift and throttle movement.
Using a stranded wire core with lubricated extrusion, the Mach cables are an ideal solution for applications with long cable runs, tight bends, or where easy and precise throttle response is required.
Mach Series cables also feature solid stainless steel output fittings.
The “high performance” MACH™ Cables are the result of our decades of experience in producing high quality, long lasting, flexible cables.
The innovative core design maximizes efficiency and minimizes lost motion, while the exclusive design of the conduit provides extremely high level of flexibility.
Features:
Suitable for outboard – inboard and sterndrive engines
High efficiency for smooth operation
High flexibility for reduced bend radius
Ideal for long complex cable routing
Maintenance free
Stainless steel cables end fittings
Blue outer jacket resists against abrasion, UV and chemicals
|
67.73 |
|
|
Euro White 4" Tachometer w/ SystemCheck Indicator 7000 RPM (Gas) (Johnson / Evinrude Outboard)
Perimeter-lighted White dial with bold Black graphics, Black aluminum bezel, contoured White pointer and flat glass lens.
Tachometers work by counting pulses generated by the ignition system, alternator, tach signal generator or magnetic pickup sender. The tach is hooked up to +12VDC, Ground and one of the signal sources listed above.
By selecting the right tach and setting the switch on the back to the correct position you let the tachometer know how many pulses are sent per each engine revolution.
These tachometers have a warning light system built into the dial that show off warning indicators when a fault is detected from the engine.
4" - Hole Size: 3.375" (85mm)
SystemCheck Warnings -
No Oil
Engine Overheat
Check Engine
Low Oil
Specifications:
Anti-scratch glass lens
Plastic Cases for corrosion resistance and long life
Perimeter-lighted Black dial
Can be adapted for 24 VDC systems
Factory P/N TC9886
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
161.99 |
|
|
Mercury 8, 9.9 (2005-Present), Johnson Evinrude 9.8 (2013-Present) & Nissan/Tohatsu 8, 9.8 with Remote TH
TROLLMaster offers a variety of different servo mounting hardware kits to allow easy installation on the most popular kicker motors. The motor-specific hardware kit must be purchased as a separate item. As long as you know the make, HP and year of your kicker motor, you can determine which hardware kit you need.
|
26.48 |
|