Voyager 2-Person Inflatable Boat Kit with Oars and Pump Inflatable fishing boat ideal for protected waters and up to three people. Four-chamber, double hull, heavy-duty construction with I-beam flooring. Accepts up to 2 HP motors with optional #30050 motor mount (not included). Integrated with bow handle, grab lines, and swivel oar locks. Features: 360 lbs weight capacity 4 chamber, double hull heavy-duty construction with I-beam flooring Inflatable bolster seat(s) included Fishing rod holder Handle and grab lines Swivel oar locks In the Box: Boat Oars Pump

Voyager 3-Person Inflatable Boat Kit with Oars & Pump Inflatable fishing boat ideal for protected waters and up to three people. Four-chamber, double hull, heavy-duty construction with I-beam flooring. Accepts up to 2 HP motors with optional #30050 motor mount (not included). Integrated with bow handle, grab lines, and swivel oar locks. Features: 600 lbs weight capacity 4 chamber, double hull heavy-duty construction with I-beam flooring Inflatable bolster seat(s) included Fishing rod holder Handle and grab lines Swivel oar locks In the Box: Boat Oars Pump

Voyager 4-Person Inflatable Boat Kit with Oars & Pump Inflatable fishing boat ideal for protected waters and up to three people. Four-chamber, double hull, heavy-duty construction with I-beam flooring. Accepts up to 2 HP motors with optional #30050 motor mount (not included). Integrated with bow handle, grab lines, and swivel oar locks. Features: 750 lbs weight capacity 4 chamber, double hull heavy-duty construction with I-beam flooring Inflatable bolster seat(s) included Fishing rod holder Handle and grab lines Swivel oar locks In the Box: Boat Oars Pump

12" x 12" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 18' to 34' Length of Tab: 12" Width of Tab: 12" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

16" x 12" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 20' to 38' Length of Tab: 16" Width of Tab: 12" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

18" x 14" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 22' to 42' Length of Tab: 18" Width of Tab: 14" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

14" x 12" Heavy Duty Performance Trim Tab Kit w/o Switch Kit -12V Lenco Electric Heavy Duty Polished Blade Trim Tab Kits are supplied with electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges, 85 degree inside taper and 1/4" diameter hinge pin. Kits equipped with Extreme Duty actuators with 5/16" SS bolts. Kit is factory assembled with full transom back plate, mechanical strain relief cable seal, adjustable C-channel mounting brackets and 3.75" sacrificial anodes. . Kit Contents: 2 each of 12-gauge stainless steel Electro-Polished trim tab blades  2 each of #15055-001 XD extreme duty actuators with 6' lead and Deutsch plugs 2 each of #30133-103  20' actuator extension wiring harnesses 1 each of the Lenco owner’s / installation manual Boat-mounting hardware supplied by customer Specifications: Suggested Boat Length: 19' to 36' Length of Tab: 14" Width of Tab: 12" Minimum Transom Height: 10.5" Blades: 12 Gauge Stainless Steel Finish: Electro-Polished Switch Kit: Sold Separately Class: Fuel Efficient Compliance: CE Certified Compatibility: Any Boat Switch Required: 15069-001 or 15070-001 Actuators: 12-volt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Par-Max HD3 Heavy Duty Water Pressure Pump - 12V - 3 GPM - 40 PSI HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life. Available in configurations up to 6 GPM (23 LPM) and 60 PSI (4.1 BAR), these pumps deliver exceptional performance.  Standard models provide good performance in an economical footprint. These configurations are available in 1-3 GPM, perfect for vessels with 1-3 outlets. A plastic housing protects the motors on these units from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for longlife, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Equipped with integrated bypass module to reduce cycling and provide smoother flow Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.13m/min)  Certifications: CE, ISO8846, RCM Ingress Protection: IPX6 WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Par-Max HD3 Heavy Duty Water Pressure Pump - 12V - 3 GPM - 60 PSI HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life. Available in configurations up to 6 GPM (23 LPM) and 60 PSI (4.1 BAR), these pumps deliver exceptional performance.  Standard models provide good performance in an economical footprint. These configurations are available in 1-3 GPM, perfect for vessels with 1-3 outlets. A plastic housing protects the motors on these units from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for longlife, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Equipped with integrated bypass module to reduce cycling and provide smoother flow Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.13m/min)  Certifications: CE, ISO8846, RCM Ingress Protection: IPX6 WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Par-Max HD5 Heavy Duty Water Pressure Pump - 12V - 5 GPM - 40 PSI HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life. Available in configurations up to 6 GPM (23 LPM) and 60 PSI (4.1 BAR), these pumps deliver exceptional performance.  Standard models provide good performance in an economical footprint. These configurations are available in 1-3 GPM, perfect for vessels with 1-3 outlets. A plastic housing protects the motors on these units from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for longlife, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Equipped with integrated bypass module to reduce cycling and provide smoother flow Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.13m/min)  Certifications: CE, ISO8846, RCM Ingress Protection: IPX6 WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Heavy Duty Toggle Switch DPST On-Off 4-Screw Cole Hersee's Heavy Duty DPST Toggle Switch, 4 Screw Terminals, 25 A Standard or long handle. Universal application. Silver contacts. Mounting stem is nickel-plated brass 15/32" -32 thread, 15/32" (11.9mm) long, and fits panels up to 9/32" (7.1mm) except where stated otherwise. phenolic housing, with plated steel cap. Nickel-plated brass mounting hardware. Blade terminals: .250 quick connect. Screw terminals: 6-32 screws. 25A at 12V, 15A at 24V, and 10A at 36V DC.

ATLAS™ 6" Set Back Hydraulic Jack Plate - Heavy Duty T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the new ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

HotShot HD4 Heavy Duty Washdown Pump - 12V - 4 GPM - 60 PSI Years of clean decks and satisfaction in the form of robust and reliable high-flow and high-pressure diaphragm pumps. The Jabsco legacy of exceptional products continues with this updated and improved lineup of washdown pumps and kits.  HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life.  Standard models provide exceptional performance in an economical footprint. A plastic housing protects the motors from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Full kit versions available which include 25' (7.6m) hose coil Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.1m min)  Certifications: CE, ISO8846, RCM  Ingress protection: IPX6 Fittings & Accessories: Quick Connect straight hosebarb and GHT fittings. Size varies by model.  90° 20 mesh Quick Connect straine  Trigger nozzle & Quick Connect hose adapters  Kit version includes 25' HoseCoil WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

HotShot HD5 Heavy Duty Washdown Pump - 12V - 5 GPM - 70 PSI Years of clean decks and satisfaction in the form of robust and reliable high-flow and high-pressure diaphragm pumps. The Jabsco legacy of exceptional products continues with this updated and improved lineup of washdown pumps and kits.  HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life.  Standard models provide exceptional performance in an economical footprint. A plastic housing protects the motors from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Full kit versions available which include 25' (7.6m) hose coil Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.1m min)  Certifications: CE, ISO8846, RCM  Ingress protection: IPX6 Fittings & Accessories: Quick Connect straight hosebarb and GHT fittings. Size varies by model.  90° 20 mesh Quick Connect strainer Trigger nozzle & Quick Connect hose adapters  No kit versions with hose offered WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

HotShot HD6 Heavy Duty Washdown Pump - 12V - 6 GPM - 70 PSI Years of clean decks and satisfaction in the form of robust and reliable high-flow and high-pressure diaphragm pumps. The Jabsco legacy of exceptional products continues with this updated and improved lineup of washdown pumps and kits.  HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life.  Standard models provide exceptional performance in an economical footprint. A plastic housing protects the motors from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Full kit versions available which include 25' (7.6m) hose coil Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.1m min)  Certifications: CE, ISO8846, RCM  Ingress protection: IPX6 Fittings & Accessories: Quick Connect straight hosebarb and GHT fittings. Size varies by model.  90° 20 mesh Quick Connect strainer  Trigger nozzle & Quick Connect hose adapters  Kit version includes 25' deluxe HoseCoil WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.