Lynx Distributor A modular DC bus bar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. Part of the modular Lynx distribution system.   Contains a positive and negative bus-bar and provides a connection for 4 individual DC equipment circuits, loads or DC groups. It has a space for individual DC fuses per DC group.  There is an optional feature of an LED for each fuse to indicate if fuse is blown. If you wish to use the fuse indication LEDs on the Lynx Distributor, it also requires a connection to a Lynx Shunt. The Lynx Shunt contains the necessary wide input (8 to 70VDC) power supply to output the required 5V (4,5V-5,5V) power requirement of the Lynx Distributor circuit board. RJ11 fly leads are used to connect the Lynx Shunt to the Distributor. This RJ11 cable is supplied with the Distributor in the box. There are two ports on the Lynx Shunt, and it is possible to use either. When all is OK, only the central LED is green; when a fuse has blown (or is missing) the central and blow fuse circuit LEDs turn red. If you are not using all connection points in your DC distribution, it may be necessary to fit dummy fuses to extinguish the red LEDs Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Shunt VE. Can The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse (not included), the built in battery monitor accurately monitors the state of charge of your battery.  The Lynx shunt contains a positive bus-bar with space to mount a CNN fuse and a negative bus-bar with a shunt. It also contains battery monitoring electronics. The Lynx shunt can send via the VE.CAN bus battery monitoring information to a CCGX or VGX or to a third party CANbus monitoring system, such as a NMEA2000. The CCGX, VGX or third party display acts as battery monitor display and is also used to set up the built-in battery monitor. The Lynx shunt is available with a VE.Can connection.   Fuse CIP140325000 - Fuse CNN 325A/80V for Lynx shunt, or alternatively a CNN fuses by Littlefuse can be used. Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

MagCode Power Clip for Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Port) MagCode Power Clip is a connection cable for the Victon's Blue Smart IP65 Chargers. Features: 12V 15 amp max *Requires Victon’s MagCode Power Port Please contact your dealer for any returns, repairs or support issues related to this product.

MagCode Power Port for Blue Smart IP65 Charger - 12V - 15 Amp Max (Requires Power Clip) MagCode Power Port is a magnetic connector for Victon's Blue Smart IP65 Chargers. Specifications: Volt: 12V Max Amp: 15 *Requires Victon’s MagCode Power Clip Please contact your dealer for any returns, repairs or support issues related to this product.

BURKS 3CR6M-V, Turbine Pump 1/3HP 1PH 230V Viton Turbine Pump and Motor unit. Bronze Fitted Cast Iron Construction w/ Viton seal & O-Ring. Close Coupled to a 1/3 Horsepower, 3450 RPM, 230 Volts, 1 Phase Motor. Ports are 1/2 Inches NPT Inlet, 1/2 Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS 3CR6M-V-SP, Turbine Pump 230v with Plug and Ground Wire Turbine Pump and Motor unit. Close Coupled to a 1/3 Horsepower, 3450 RPM, 230 HZ , 60 Volt, 1 Phase, ODP Motor. Ports are 1/2 Inches NPT Inlet, 1/2 Inches NPT Outlet.   UNSPSC Code: 40150000

Flojet 20381-V Viton O'Ring For Ports  

March MDXT-3 Magnetic Drive Pump Applications for the include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.   March Pump's industrial MDXT-3 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 8.5 gallons per minute at ;4 feet, and its maximum head is 19 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 0.5 inch female pipe thread, and the outlet is 0.375 inch female pipe thread. The standard motor is a 1 Phase 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March MDXT-3 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.   The MDXT-3 has pumped has pumped Acetic Acid, Acetone, Ammonium Sulfate, Citric Acid, Ethylene Glycol, Ferric Sulfate, Hydrogen Peroxide, Potassium Hydroxide, Sodium Chloride, Fresh Water, Salt Water, and many more chemicals.   Unit System 60Hz 50Hz Max Flow 8.5 GPM 30 LPM Max Head 19 FT 4 M Power .04 HP .029 KW Electrical 115V 50/60HZ or 230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"FPT Outlet 3/8"FPT Wet End Polypropylene (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Buna N (O-Ring), Ceramic Magnet

FINISH THOMPSON M100004-5 IMPELLER SHAFT, 27"

FINISH THOMPSON M100005-3 40" PF INTAKE TUBE

FINISH THOMPSON M100007 BOTTOM BEARING

FINISH THOMPSON M100010 CENTER BEARING

FINISH THOMPSON M100015 WALL MOUNT BRACKET

FINISH THOMPSON M100018-1 PFP IMPELLER HOUSING

FINISH THOMPSON M100088 BUNG ADAPTER GALV STEEL