|
5/8" x 50' Boxed Type A2 Fuel & Vent Line Hose - Black
Trident 5/8” A2 Fuel Hose for gasoline vent hose (including ethanol blends) and diesel (including bio diesel blends). This hose is built with the best fuel, fire and age resistant formulation.
Features:
Provides extraordinary resistance to aging, fire, heat, cold, and the ozone
Also provides excellent bend-ability
NMMA Type Accepted & CE certified
Application:
Fuel Hose for vent and diesel distribution
For all marine fuels including gasoline, alcohol blends, diesel and bio-diesel
Construction:
Tube: Nylon Internal Barrier, NBR
Cover: NBR/PVC Blend
Reinforcement: Polyester 2 spiral
Temperature Range: -20°F to 212°F (-28ºC to 100ºC)
Length: 50 ft. (15 m) Boxed
Specifications:
Inner Diameter: (inch) 5/8" / (mm) 15.9
Outer Diameter: (inch) 0.960 / (mm) 24.4
Burst Pressure: (psi) 200 / (mpa) 1.38
Working Pressure: (psi) 50 / (mpa) 0.34
Bend Radius: (inch) 3" / (mm) 76.2
Weight: (lb/100 ft.) 25.84 / (kg/m) 11.72
*The #317 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2
|
160.07 |
|
|
3/8" x 50' Boxed Barrier Lined B1-15 EPA Compliant Outboard Fuel Line Hose - Gray
This hose is built with the best fuel and age-resistant formulations and a unique "Barrier Liner" on the inside surface of the tube, so the fuel is not in direct contact with rubber. This greatly reduces fuel permeation and prevents ethanol degradation of the rubber tube, which can cause small pieces of rubber to reach and damage the engine. That is particularly important considering the prospect of higher ethanol blends (E-15) available at gas stations next year.
Features:
Provides extraordinary resistance to fuel permeation, aging, heat, cold, and ozone
Also, provides excellent rope-like bend-ability and fitting retention
For both gasoline (including ethanol blends up to E85) and diesel (including bio diesel blends up to 100%)
EPA Certified and CARB Executive Order for low permeation Type B1-15
NMMA Type Accepted & CE certified
Application:
Marine Fuel Hose for distribution, return, vent and transfer
For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel
Construction:
Tube: Fluoroplastic Internal Barrier
Cover: Gray CPE Rubber
Reinforcement: 2-Spiral Polyester Plies
Temperature Range: -20°F to 212°F (-28ºC to 100ºC)
Length: 50’ (15m) Boxed
Specifications:
Inner Diameter: (inch) 3/8" / (mm) 9.50
Outer Diameter: (inch) 0.588 / (mm) 14.9
Burst Pressure: (psi) 175 / (mpa) 1.21
Working Pressure: (psi) 35 / (mpa) 0.24
Bend Radius: (inch) 4" / (mm) 101.6
Weight: (lb/100 ft.) 10.5 / (kg/m) 0.156
Permeation Rate (Standard is (15g/m^2/24hrs (CE10)): 5.0
*The #305 series exceeds ABYC H-24, SAE J1527, ISO 8469 B1, USCG Type B1-15
|
121.68 |
|
|
1/2" x 50' Boxed Reinforced PVC (FDA) Cold Water Feed Line Hose - Drinking Water Safe - Translucent Blue
Trident 165 Series Blue - polyester reinforced PVC hose for "Cold Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures as low as -18.4ºF (- 28ºC) and can handle pressures up to 250 psi (varies based on i.d size).
Features:
The Blue cover allows for easy identification of "Cold Water" lines on your boat
Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility
This hose is safe for use with drinking water
Application:
Perfect for cold pressurized applications, water feed, drains, and vent lines
Construction:
Tube & Cover: Clear FDA tube
Color: Blue Transparent
Reinforcement: Polyester
Temperature Range: -18°F to 149°F (-28°C to 65°C)
Length: 50’ (15.24m)
Specifications:
Inner Diameter: (inch) 1/2" / (mm) 12.7
Outer Diameter: (inch) .777 / (mm) 19.6
Working Pressure: (PSI Vac In./Hg) 250 / (bar) 17
Bend Radius: (inch) 0.98" / (mm) 25
*Burst Pressure is 4 x Working Pressure
|
50.63 |
|
|
1-1/2" x 50' VAC XHD Bilge & Live Well Hose - Hard PVC Helix - Black
Trident VAC XHD Bilge and Live Well Hose. Helical PVC reinforcement provides excellent flexibility and bend radius for live well and heavy-duty bilge applications. It has a smooth outer surface to allow for easy clamping. The excellent bend radius of this product gives you the flexibility of a rubber hose making installations a breeze.
Features:
149 series of hoses is extra flexible
Application:
Bilge and live well hose
Specifications:
Tube & Cover: Hard PVC helix
Color: Black
Reinforcement: PVC Helix
Temperature Range: 10°F-120°F (-12°C-48°C)
Boxed: 50ft. / (15.2m)
Inner Diameter: (inch) 1-1/2" / (mm) 38.1
Outer Diameter: (inch) 1.792" / (mm) 45.5
Working Pressure: (Psi Vac In./Hg) 28 / (Bar) 1.93
Weight: (Lb./ 50 ft.) 22 / (Kg/m) 9.98
Bend Radius: (inch) 4" / (mm) 101.6
*Burst Pressure is 4 x Working Pressure
|
195.35 |
|
|
Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.
|
109.00 |
|
|
Double Braided Nylon Dock Line - 1/2" x 50' - Black
Features:
Double Braided Nylon Dock Lines
100% premium double braided nylon
Professionally spliced soft eye at one end
Yacht whipped at the bitter end and splice point
|
31.54 |
|
|
Hatch Handle Latch - 3-1/8" x 2-11/16"
Constructed of sand cast brass with a chrome plated finish. These Hatch Handle Latches are ideal for use on doors, hatches, lazarettes, and dock boxes. Handle pivots out to open hatches and lays flush when not in use for a clean appearance. Adjustable locking arm adds additional security. Installs with four #8 FH fasteners (not included). Once installed, the locking arm can be trimmed to length.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
68.57 |
|
|
JABSCO SP1402-06 WOODRUFF KEY 1/8 X 5/8 ST
|
19.66 |
|
|
Stainless Steel Louvered Vent - 9-1/8" x 4-5/8"
Louvered Vents are designed to promote air circulation and prevent mold, mildew, and unpleasant odors. Ideal for cabin doors, lockers, dock boxes, etc. Easy to install with six #6 RH fasteners (not included). Corrosion resistant stamped 304 stainless steel construction.
|
16.32 |
|
|
Stainless Steel Louvered Vent - Oval - 9-1/8" x 4-5/8"
Louvered Vents are designed to promote air circulation and prevent mold, mildew, and unpleasant odors. Ideal for cabin doors, lockers, dock boxes, etc. Easy to install with six #6 RH fasteners (not included). Corrosion resistant stamped 304 stainless steel construction.
|
18.29 |
|
|
Poly Pro Anchor Line with Snap - 1/4" x 50' - Yellow
Hollow Braid Anchor Line with Snap.
Features:
100% premium multi-filament polypropylene floating rope
Plated steel Spring Hook (155630)
Packaged in a reusable clamshell pack (304206050YW-1) or easy to dispense spool
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
7.70 |
|
|
Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.
|
21.99 |
|
|
Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.
|
24.99 |
|
|
11-1/8" x 24" Manual Seat Slide
This universal, low-profile design provides frictionless operation and is easily adaptable for a multitude of marine applications. Its high-strength polymer glides provide the smooth movement with a durable locking action. It comes with a front-mounted activation lever, which is easily accessible in all five positions when seated.
Features:
Meets ABYC H31 testing standards
Precision-machined 6000-series aluminum chassis
Double pin positive side lock
High-strength polymer glides provide self-lubricated, rattle-free, smooth operation
Features five adjustable, equally spaced positions with 3-5/8” of travel
Secure fit with universal mounting bolt pattern on box applications
Front activation paddle that slides with the seat for ease of use
Ideal for seats 29" to 40” wide
Ideal seat length/depth is 12" to 14"
Made in the USA
3-year limited warranty
|
596.09 |
|
|
11-1/8" x 36" Manual Seat Slide
Designed for helm chairs and benches 41" to 54" wide, this newly designed slide features a travel distance of up to 3-5/8" with five adjustable positions. Its high-strength polymer glides create a smooth, rattle-free design. Quickly and easily adjust seats using the front-mounted activation paddle handle, which is always accessible in all five positions.
Features:
Meets ABYC H31 testing standards
Precision-machined 6000-series aluminum chassis
Double pin positive side lock
High-strength polymer glides provide self-lubricated, rattle-free, smooth operation
Features five adjustable, equally spaced positions with 3-5/8” of travel
Secure fit with universal mounting bolt pattern on box applications
Front activation paddle that slides with the seat for ease of use
Ideal for seats 41" to 54” wide
Ideal seat length/depth is 12" to 14"
Made in the USA
3-year limited warranty
|
662.80 |
|