|
White Vinyl Cover for Nightwave
Designed specifically for the Nightwave camera with a tightening strap for a snug and secure fit, our vinyl slip-on covers provide long-lasting protection against water, dust, dirt, and UV rays. Choose black or white to match your vessel and protect your night vision investment when you’re docked and in long-term storage. This is a SIONYX official accessory.
|
36.00 |
|
|
The Coast Guard's Seventh District has received at least three reports in the past few months regarding unapproved replacements of 406 EPIRB batteries by servicing companies having no association with the EPIRB manufacturer. These unauthorized battery installations would likely result in a failure of this critical item of lifesaving equipment, and as such are not in compliance with the operational readiness requirements of 46 CFR.
The following is a typical excerpt from an EPIRB manufacturer report:
"The unit was opened and a foreign battery was found inside. The battery was built up using (manufacturer) fuses and wiring salvaged from the original (manufacturer) battery. They then covered their battery with the original (manufacturer) yellow heat shrink, (manufacturer) labels and taped it together. This was then covered with a black heat shrink wrap. The connections were soldered and not spot welded, as is required by the design and is performed in (manufacturer) production. The battery measured 8.7 volts. Our batteries read 9+ volts when they are new. This battery was installed one week prior to it being brought into (manufacturer).
There was also evidence of water intrusion due to the crack in the top cap, which (servicing company) did not recognize as they are not trained in these matters.
The EPIRB was condemned by (manufacturer) and the customer was notified when he came to pick the unit up."
Every approved (i.e., accepted by the FCC) EPIRB is tested during its approval process using a battery, or batteries, specified by the manufacturer. Approved EPIRBs come with a user's manual which describes battery maintenance and replacement procedures. In order for the EPIRB to remain within the conditions of its approval, the manufacturer's instructions in the user's manual must be adhered to. To ensure that replacement batteries are of the same type with which the EPIRB was approved, and are correctly installed, manufacturers typically specify that battery replacements only be done by the manufacturer or a manufacturer-approved shop.
Any modification or changes to an EPIRP must be made in accordance with the manufacturer. The use of alternative replacement parts or batteries is prohibited and may prevent the device from meeting lifesaving requirements. The Coast Guard strongly reminds EPIRB owners and servicing facilities to be aware of the compliance implications and potential for equipment failure stemming from any EPIRB modification or unauthorized battery replacement.
This safety alert is provided for informational purposes only and does not relieve any domestic or international safety, operational or material requirement. Questions regarding the information presented in this alert may be addressed to LCDR Vince Gamma of the U.S. Coast Guard Headquarters Lifesaving & Fire Safety Standards Division at 202.372.1396 or Vincent.A.Gamma at uscg.mil.
|
|
|
Edson International will introduce a new Radar, Satellite Antenna and Accessory Mounting System at the upcoming Miami Boatshow.
Known as the Vision Series, the new product line delivers styling and design features unlike any mounting solution currently available.
All-new sleek, modern design.
First all modular system - extremely versatile.
Easy to select and install for any radar, dome, light or camera combination.
Easy to add accessories.
Upgradable for future additions and modifications.
Powder coated aluminum construction
Designed and manufactured at Edson's Massachusetts facility, the new towers provide a cost effective yet performance enhancing solution to mount the latest electronic radar & satellite domes, cameras, lights, and antennas on a wide range of power boats. A unique series of Mounting Plates allow the customer to mount any manufacturer's antenna on to any Edson Vision Series Tower, greatly simplifying the ordering process for the customer and stocking requirements for the dealer.
The Vision Series towers will be available in single, dual and the first production triple mount configuration. Also available are standardized mounts to fit a wide range of products allowing electronics installers to stock a single product for multiple applications. "The Edson Vision Series is a stylistic departure from what our industry is used to seeing in an electronics mount,"says Rick Cowen, Product Manager for Edson's NavCom line. "These towers are really going to turn some heads and visually enhance the lines of powerboats, new and old."
See all Edson Products at Edson Marine ( http://www.clrmarine.com/462m4/manufacturers/edson-marine.html )
Vision Series mounts are available in a variety of standard and customized heights to fit most recreational powerboat designs. The unique Mounting Plates, Optional Antenna Wings, and Light Arms are easily added to the basic towers allowing a versatile, but simple installation for multiple antennas, receivers and lights. Custom height towers and configurations will also be available.
SEE THE EDSON VISION SERIES ELECTRONICS MOUNTING SYSTEM AT MIAMI BOATSHOW CONVENTION CENTER ELECTRONICS ROOM - BOOTH #1686
|
|
|
Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.
The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces!
For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.
SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html
Specials Closeouts Remanufactured Rebates
|
|
|
Passport Potty Portable Toilet - Grey - 18L
Features:
2-section Portable Flush Toilet
Strong, durable construction
Bi-directional piston pump rinse
Leak and odor proof seal
Waste level indicator
Large fresh water capacity
8L to 24L holding tank capacities
|
99.55 |
|
|
KNB - 100 Replacement Knob - Titanium Grey
Replacement billet knob for VR-140 Elite mirrors.
*Sold as an Individual
|
13.34 |
|
|
Board Rack Replacement Knob - Titanium Grey
Replacement Swivel Release Knob for the Clamping and Bungee Board Racks.
*Sold as an Individual
|
15.58 |
|
|
533-VW-S VHF Top Section for 532-VW or 532-VW-S
Digital Antenna 533-VW-S 8' VHF Replacement Top Section for 16' VHF Antennas. White.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
306.23 |
|
|
Extra Strong 20' Telescoping Carbon Fiber Outrigger Poles for Sidewinder Mount
Advanced Carbon Composite Telescoping outriggers. Lee's carbon fiber poles are by far stronger and lighter than any other aluminum pole on the market today.
Made "Extra Strong" by utilizing the lower four sections of a five section outrigger pole for an increased outer diameter and stronger pole.
The perfect solution for trolling a variety of baits.
Features:
Light Weight – Makes deployment, retrieval, raising, and lowering a breeze
Strength – Spreaders become unnecessary
A glossy clear coat finish is standard
Technical Specifications:
Length - 20'
Number of Sections - Four (4)
Mounting Base - Lee's Sidewinder 1-5/8"
Rigging – Double rigging
Line Strength – 400 lb. black monofilament
Line Length -
*Sold as a Pair
|
1804.27 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Mercruiser I/O & Mercury O/B with Oildyne Pump
Replacement tilt trim motor that will fit Mercruiser I/O and Mercury Outboards with Oildyne pump. 12 Volt, Ring Terminal Ends
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 17649
MERCURY Tilt Trim Motor 17649A1
MERCURY Tilt Trim Motor 17649A02
MERCURY Tilt Trim Motor 17649T
MERCURY Tilt Trim Motor 87828
MERCURY Tilt Trim Motor 891736T
SIERRA Tilt Trim Motor 18-6772
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
164.72 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Late Model Volvo Penta with Oildyne Pump - 2 Wire
Replacement tilt trim motor that will fit 6227, Late model Volvo Penta, w/Oildyne pump, 2-wire connection.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
VOLVO Tilt Trim Motor 3151278
VOLVO Tilt Trim Motor 3858071
VOLVO Tilt Trim Motor 854525-3
SIERRA Tilt Trim Motor 18-6805
SIERRA Tilt Trim Motor 18-6817
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
131.58 |
|
|
Premium Replacement Tilt Trim Motor for Late Model Mercruisers with Oildyne Pump
Replacement outboard tilt trim motor that will fit late model Mercruiser w/Oildyne pump, Ring Terminal Ends.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY 14336A6
MERCURY 14336A8
MERCURY 14336A9
MERCURY 14336A12
MERCURY 14336A15
MERCURY 14336A17
MERCURY 14336A20
MERCURY 14336A25
MERCURY 14336A31
MERCURY 865380A03
MERCURY 865380A13
MERCURY 88183A5
MERCURY 88183A6
MERCURY 88183A8
MERCURY 88183A11
MERCURY 88183A12
MERCURY 88183A13
MERCURY 88183A25
SERRA 18-6769 / 18-6769-1
SIERRA 18-6813
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
425.99 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Mercury/Mariner Outboards with Design II 3 RAM
Replacement outboard tilt trim motor that will fit Mercury/Mariner outboards w/Design II 3 ram, three-wire trim units, Hollow-hex shaft W/AFT FILL RESERVOIR, 3-wire connection, 2-bolt mount, Shaft adaptor, and O-ring included, Ring Terminal Ends.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 811628
MERCURY Tilt Trim Motor 828708A1
MERCURY Tilt Trim Motor 878265A6
SIERRA Tilt Trim Motor 18-6774
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
231.76 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Early Model Yamaha - 3 Wire, 3-Bolt Mount
Replacement tilt trim motor that will fit Yamaha Early 70, 90,115,150-200 HP, 3-wire connection, 3-bolt mount, Ring Terminal Ends, 4-mm thick shaft blade with 68.3-mm mounting collar. Includes O-ring.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
YAMAHA Tilt Trim Motor 6E5-43880-01
YAMAHA Tilt Trim Motor 6E5-43880-02
YAMAHA Tilt Trim Motor 6H1-43880-00
YAMAHA Tilt Trim Motor 688-43880-10
YAMAHA Tilt Trim Motor 688-43880-11
SIERRA Tilt Trim Motor 18-6259
SIERRA Tilt Trim Motor 18-6821
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
239.99 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Yamaha 2011-2021
Replacement outboard tilt trim motor that will fit Yamaha 150-250HP, 2011-2021 4 Stroke.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
YAMAHA Tilt Trim Motor 63P-43880-11-00
YAMAHA Tilt Trim Motor 63P-43880-21-00
YAMAHA Tilt Trim Motor 63P-43880-22-00
YAMAHA Tilt Trim Motor 63P-43880-10-00
YAMAHA Tilt Trim Motor 6KW-43880-00-00
YAMAHA Tilt Trim Motor 6KW-43880-01-00
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
398.40 |
|