By now, the skipper in your life has probably dropped a few hints about holiday gifts. Was it the note left on the coffee pot about Articulated ABS Barrel Hinge foldable Aluminum Tubing? At first glance, one would have thought that the message was a reminder about being out of coffee filters. Then it comes back to you that there was a conversation in the car about GemLock Assembled Folding Struts.    Foldable aluminum tubing is one of the hottest trends in stainless steel hardware for marine canvas and solar panel frames. The tubing offers versatility in styling, high quality, and ease of use. https://www.clrmarine.com/462m4/manufacturers/g/gemini-marine.html   Back to your captain's holiday gift list. Was there a subtle hint, while you both were swimming off the boat, and your skipper showed concern that the transom ladder seemed a little short by a few steps? She would find getting out of the lake sooooo much easier if she didn't have to reach her foot up so far to the lowest step. She had also mentioned a discussion with other boat captains about the Extend Your Step, an easy-to-use boat boarding ladder extension. Several of her sailing buddies already have them and raved about the ease and portability. .   All of the products mentioned above are available at CLR Marine.com. How confident are the folks at CLR Marine about the Extend Your Step regarding ease in boarding and extending the ladder length? This product reflects the confidence and integrity of CLR Marine's owner, Chuck Reed. He invented the Extend Your Step! When shopping for the extending ladder, be sure to check out the Extend Your Step Three – a longer and non-moving version of the Extend Your Step! https://www.clrmarine.com/Boat-Boarding-Ladder-Extension   It's possibly time for your captain to give the best seat in the house – on your boat- an upgrade. There is no better place to watch the glint of the sun on the waves than in a stern perch seat. Stern rail seats are now available for older model boats, even pre-1993, and the seats are removable. https://www.clrmarine.com/sternperch-seats.html     Stocking Stuffers   Floatable key rings. If you are old enough to have keys, then you are old enough to lose keys. House keys, boat keys, car keys – when these fall into the drink and aren't retrievable, your boat outing takes a turn for the worse. Car key fobs are expensive to replace. Neon colored strong straps or carabiner clips offer added security against key loss. DryCASE Smartphone Case   The DryCASE waterproof cell phone case keeps your electronics protected, whether surfing, paddle boarding, or canoeing. The DryCASE uses vacuum seal technology to ensure a watertight seal every time. Best of all, you'll still be able to use your touch screen to text or make calls, and the crystal clear covering makes taking pictures a cinch. When you purchase the DryCASE you will also receive a small hand pump, neoprene armband, and a lanyard  $36.92. https://www.clrmarine.com/m4/45443—drycase-smartphone-case.html   RAM Mount AQUA BOX Medium RAM AQUA BOX® cases provide sealed enclosure and protection for your handheld devices. The clear, touch through screen allows you to view your electronics and use their function keys while in place. There is even a place for a small lock to serve as a theft deterrent. The AMPS hole pattern on the back of the box allows this enclosure to be attached to many RAM mounting bases and kits. Ideally suited to Motorcycles and ATV's, the AQUA BOX keeps your portable devices safe, dry, and accessible $36.49.   Scotty 130 Paddle Safety Leash   Paddles, rods, nets, gaffs, and many other items can be secured while in use with the Scotty Safety Leash. Features include two extra strong Scotty 1009 swivel snaps; super-strong Flex Coil cord allows for maximum unrestricted movement and stretches to approx. 6'. Unit Includes two figure eight securing straps $11.99. https://www.clrmarine.com/m4/37811--scotty-130-paddle-safety-leash-black.html Gifts under $30.00   Don't forget about covers for your water toys. The Dallas Manufacturing Co – Pedal Boat Cover will keep your pedal boat dry, dirt free, and protected from the sun when not in use. Features include 150 Denier Silver Polyester, fits both 3 and 5 Person Pedal Boats and is backed by a one year warranty $13.19.  https://www.clrmarine.com/m4/36879—dallas-manufacturing-co-pedal-boat-polyester-cover.html   Mustang Lil' Legends 70 Youth Vest -  Fluorescent Yellow-Green/Gray   Have guests arrived on your boat with a small young family member who needs a life vest? The Mustang Lil's Legends is a quality youth vest, and it never hurts to have a spare on board. It fits a child 50-90 pounds  $21.59.  https://www.clrmarine.com/m4/49897—mustang-lil-legends-70-youth-vest-50-90lbs-fluorescent-yellow-green-gray.html     Be good—Santa's watching. Stay healthy. Fair Winds. Smooth sailing.   To obtain more information about the products and services mentioned in this article, please contact CLR Marine https://www.clrmarine.com ______________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com     

Edson International will introduce a new Radar, Satellite Antenna and Accessory Mounting System at the upcoming Miami Boatshow. Known as the Vision Series, the new product line delivers styling and design features unlike any mounting solution currently available. All-new sleek, modern design. First all modular system - extremely versatile. Easy to select and install for any radar, dome, light or camera combination. Easy to add accessories. Upgradable for future additions and modifications. Powder coated aluminum construction   Designed and manufactured at Edson's Massachusetts facility, the new towers provide a cost effective yet performance enhancing solution to mount the latest electronic radar & satellite domes, cameras, lights, and antennas on a wide range of power boats. A unique series of Mounting Plates allow the customer to mount any manufacturer's antenna on to any Edson Vision Series Tower, greatly simplifying the ordering process for the customer and stocking requirements for the dealer. The Vision Series towers will be available in single, dual and the first production triple mount configuration. Also available are standardized mounts to fit a wide range of products allowing electronics installers to stock a single product for multiple applications. "The Edson Vision Series is a stylistic departure from what our industry is used to seeing in an electronics mount,"says Rick Cowen, Product Manager for Edson's NavCom line. "These towers are really going to turn some heads and visually enhance the lines of powerboats, new and old."   See all Edson Products at Edson Marine ( http://www.clrmarine.com/462m4/manufacturers/edson-marine.html )   Vision Series mounts are available in a variety of standard and customized heights to fit most recreational powerboat designs. The unique Mounting Plates, Optional Antenna Wings, and Light Arms are easily added to the basic towers allowing a versatile, but simple installation for multiple antennas, receivers and lights. Custom height towers and configurations will also be available.   SEE THE EDSON VISION SERIES ELECTRONICS MOUNTING SYSTEM AT MIAMI BOATSHOW CONVENTION CENTER ELECTRONICS ROOM - BOOTH #1686

ECI-100 Universal Engine & Control Interface The ECI-100 Universal Engine and Control Interface is an innovative and affordable solution for bridging engine instrumentation and drive-by-wire steering with Raymarine autopilot and navigation systems. A simple isolated CAN Bus solution, the ECI-100 offers reliable integration with Raymarine's latest generation of multifunction displays and also delivers a seamless autopilot steering interface to Raymarine's Evolution EV-2 Drive By Wire autopilot system. Benefits: A simple, single point of connection for engine data and drive-by-wire autopilot control Affordable and uncomplicated solution eliminates the need for multiple engine and autopilot gateways Brings Raymarine's Evolution 9-axis sensor and adaptive autopilot control to drive-by-wire propulsion without the need for a proprietary autopilot gateway View engine data displays and enjoy full autopilot control alongside Raymarine's industry-leading radar, sonar and navigation technologies using a single touch screen display. From our space saving aSeries, to our flagship big screen gS Series, engine information displays and autopilot control are available on any display running LightHouse v8 or later Access easy to customize displays to show engine performance data, fuel consumption, alarms, and much more View engine information displays on your smart phone or tablet with Raymarine mobile apps Simple to install ECI-100 makes engine and navigation integration a reality for virtually any size vessel ECI-100 Engine Data Parameters The ECI-100 Universal Engine and Control Interface identifies the following parameters: Engine speed Engine oil temperature Engine temperature Engine oil pressure Engine coolant pressure Engine fuel rate Boost pressure Battery potential Transmission oil pressure Transmission oil temperature Total engine hours Fuel tank level Trip fuel used (calculated by ECI-100) Alternator potential Engine torque Engine percent load Transmission gear VIN (not shown on the display) Software number (not shown on the display) Simple Integration, Powerful Performance The ultra-compact ECI-100 connects directly to the industry-standard NMEA2000 or SAE* J1939 Engine Data Bus used by major marine engine manufacturers including: Volvo Penta Yamaha Marine (Command Link Plus only) Caterpillar Yanmar Marine Raymarine is committed to delivering seamless integration with leading marine engines. Visit www.raymarine.com for the latest engine compatibility information. An industry standard DeviceNet port connects the ECI-100 to manufacturerspecific CAN bus cabling. The ECI-100 then connects to NMEA2000 networks using the SeaTalkng cabling system. Each of the ECI-100's isolated ports is powered independently ensuring reliable, worry-free performance from both navigation electronics and engine systems. * SAE - Society of Automotive Engineers standard

Sierra replacement engine couplers for Mercruiser engines.

Engine Mount Kit - 4 Engine Mounts f/Small Yanmar Engines (Yanmar*) * Suitable for the Yanmar 1GM, 2GM, 3GM, 3YM, 3HM and 3JH series engines The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

Sherwood P1016 Engine Cooling Pump The Sherwood P1016 flexible impeller engine cooling pump replaces the Sherwood pump P1016-01 Applications for the Sherwood P1016 pump include: Cummins QSD 2.0 & 2.8 engines, replaces Cummins 854179001, Mercury MerCruiser 879312023 and 854179001 pumps. This is a genuine Sherwood P1016 flange mounted boat engine cooling pump, using raw water intake (river water or sea water) to cool the engine. The Sherwood P1016 is supplied complete with a 12 vane through key drive flexible neoprene impeller. The raw water engine cooling pump is the heart of the marine engine, supplying a continuous flow of raw water to maintain temperatures consistent with the demanding engine performance. Over the years, Sherwood raw water pumps have developed a reputation of excellence in quality; and today are chosen for their performance and dependability by the most prestigious marine engine manufacturers. Sherwood pumps are one of the largest suppliers of flexible rubber impeller cooling pumps for marine engines in the USA. They can be found fitted on some of the most well known engine brands in both pleasure and commercial boats. To ensure that your boat engine cooling pump performs as required, regular preventative maintenance and inspection should be carried out. The Sherwood engine cooling pump impeller should be replaced every 3 - 12 months depending on application.

WP015 Water Pump Repair Kit for Suzuki Outboard Engines This water pump repair kit is designed for specific Suzuki outboard engines. Fits: Suzuki 4 Stroke Outboard 20HP, 25HP, 30HP, 35HP, 40HP, and 50HP boat motor engine parts model DT20, DT25, DT25C, DT30, DT30C, DT35, DT40C, DF25, DF30, DF40, and DF50 2 Replaces: Suzuki Water Pump Repair Kit 17400-96404 Suzuki Water Pump Repair Kit 17400-96403 Suzuki Water Pump Repair Kit 17400-96402 Suzuki Water Pump Repair Kit 17400-96401 Suzuki Water Pump Repair Kit 17400-96400 Suzuki Water Pump Repair Kit 17400-96354 Suzuki Water Pump Repair Kit 17400-96353 Suzuki Water Pump Repair Kit 17400-96352 Suzuki Water Pump Repair Kit 17400-96351 Suzuki Water Pump Repair Kit 17400-96350 Johnson/Evinrude OMC Water Pump Repair Kit 0778317 Johnson/Evinrude OMC Water Pump Repair Kit 5031415 Johnson/Evinrude OMC Water Pump Repair Kit 5032166 Johnson/Evinrude OMC Water Pump Repair Kit 5034358 Johnson/Evinrude OMC Water Pump Repair Kit 5031744 Warranty Information When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications. Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Globe Impeller 1000 Globe Impeller Model 1000 Replaces the following impellers Mercruiser 47-89984 Mercury Marine 18-3017, 47-30221, 47-65960, 47-85460, 47-89984, 47-89984B2, 47-89984T, 47-89984T4 Sierra Marine 18-3017   Weight: 0.5 lbs. Od (in/mm): 2 11/32" / 59.5 Width (in/mm): 1 19/64" / 32.9 Shaft Size (in/mm): 7/8" / 22 Drive Type: Keyway Core Type: Brass Number of Blades: 6 Silhouette Letter: K Type: Water   Made to Order - Please allow 8 to 12 weeks for delivery   Globe Part number 01-12-1590

Engine Mount w/6.85" Footprint - 5/8" Stud - 50-75lbs Capacity Per Mount *Suitable for the Yanmar 1GM, 2GM, 3GM, 3YM, 3HM and 3JH series engines The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull. To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products. R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain. How To Select (details required): 1.Define the total weight of the engine and the transmission. 2.Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine). 3.Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine). 4.Determine the stud necessary stud diameter and footprint of the mount. 5.Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range. Example: Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8". Total weight is 590lbs. 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037 Why R&D Marine Engine Mounts? Designed for marine use, accepts propeller and engine thrust in both directions Offers a fail safe design R & D Marine Mounts are height adjustable Pre-loaded to reduce movement Slotted holes in base to assist in alignment Mount types to fit all applications

JMP Marine JSK0080 Cummins Engine Cooling Seawater Pump Major Service Kit Replaces Cummins 4930629, John Deere DZ108626, Sherwood 25045.  Services Pumps: JPR-C1100, Cummins 3349392, 4929178, 5260393, JPR-JD60IF2, John Deere DZ108620, Sherwood G2910X   JSK0080 JMP Marine Cummins Engine Cooling Raw Water / Seawater Pump Major Service Kit   Replacement and Equivalent to: Cummins Kit 4930629 John Deere Kit DZ108626 Sherwood Kit 25045   Please Note: JSK0080 includes all internal parts for full entire rebuild of pump vs Cummins kit 5260396 which has less parts. You get ALL PARTS with JMP Marine kits! Parts are fully compatible to genuine and can be used to service both JMP Marine pumps JPR-C1100, JPR-JD60IF2 along with Genuine OEM pumps!   Kit Includes All Internal Parts for full rebuild: 8359-01 (FLEXIBLE IMPELLER) - QTY:1 CAMSET0032 (CAM SET) - QTY:1 MCSSET0019 (MECHANICAL SEAL SET) - QTY:1 SHA0093 (SHAFT) - QTY:1 ORG0055 (O-RING) - QTY:1 ORG0054 (O-RING) - QTY:1 RET0042 (OIL SEAL) - QTY:1 COV0041 (BEARING COVER) - QTY:1 BER0052 (BEARING) - QTY:2 WER0020 (WEAR PLATE) - QTY:1 COV0038 (END COVER) - QTY:1 SNP0013 (SNAP RING) - QTY:1 BOL0036 (SPRING WASHER) - QTY:5 BOL0007 (END COVER BOLT) - QTY:5   Services JMP Marine & OEM Genuine Engine Cooling Raw Water / Seawater Pumps: JPR-C1100 Cummins Replacement Pump JPR-JD60IF2 John Deere Replacement Pump

Raymarine A65 GPS Chartplotter The Raymarine A65 GPS Chartplotter is a compact, yet powerful navigation system that combines simplicity with advanced chartplotting and optional HD Digital fishfinder technology. A Direct sunlight viewable display and rugged submersible construction make the Raymarine A65 the perfect fit for center consoles and open cockpits.   Raymarine, the E-Series From Raymarine, the E-Series Multifunction Networkable Navigation Displays, Raymarine E-Series delivers chartplotter, fishfinder, radar, and video in an easy to use networked navigation system.   Raymarine has a new Manufacturer's Warranty Policy Effective January 1, 2008, this new and improved policy continues Raymarine's proud tradition of best-in-industry coverage and support for all of its products. You will find that the new policy offers many advantages to both consumers and dealers alike.

Globe Impeller 075 Globe Impeller Model 75 Replaces: Ancor J050007, CEF 500107, Detroit Diesel 5194205, Ford Lehman 1210, Jabsco 1210-0001, Johnson Pump 09-1027B-1, 09-1027B-10, 1027B-1, 1027B-10, Northern Lights 145116140, 1210-0001, 25-12002, 25-12060, Onan 131-0050, 132-0162, Perkins 460038, Pleasurecraft R061003, Sierra Marine 18-3081, Universal 302571, Vetus IMP 00201, Volvo Penta 386257, 825940, 860203, 860203, 875811, 876243, 3858256, 3862465, 3862567, Westerbeke 302571, Yanmar 129670-42530, 129470-42531, 129470-42532, 129670-42610. Weight: 0.2 lbs. Od (in/mm): 2 1/4" / 57 Width (in/mm): 1 1/4" / 31.5 Shaft Size (in/mm): 5/8" / 16 Drive Type: 12 pt Spline Core Type: Brass Number of Blades: 12 Silhouette Letter: G Liquid Type: Water Includes matching Gaskets or O-rings

Globe Impeller 100 Globe Impeller Model 100 Replaces the following impellers Ancor 500106 Caterpillar 3N1906 Cummins 650607 Detroit Diesel 5193602, 5196629, 5199148 Ford Lehman 920 Gray Marine 74306, 74340 Jabsco 1111-0001, 14868-0001, 31070-0051, 4325-0480, 5915-0001, 702-0001, 920-0001, 920-0008, 920-0009, 964-0001 Johnson Pump 09-1028B, 09-1028B-1, 09-1028BT-1, 1028B-1 MAN Diesel 50.06506-0091 Oberdorfer 7441, C7441 Perkins 460024, 24880031 Pleasurecraft R061003E Sierra Marine 18-3077 Volvo Penta 801277, 825941, 875593, 877061, 3841697 Yanmar 127610-42200   Weight: 0.3 lbs. Od (in/mm): 2 9/16" / 65 Width (in/mm): 2" / 51 Shaft Size (in/mm): 5/8" / 16 Drive Type: 12 pt Spline Core Type: Brass Number of Blades: 8 Silhouette Letter: H Fuel Type: Water   Includes matching Gaskets or O-rings   Globe Impeller number 01-12-1060

Globe Impeller 1101 Globe Impeller Model 1101 Replaces the following impellers CEF 500108 Gray Marine 74366 Jabsco 1427-0001, 2877-0001, 6174-0001 Johnson Pump 09-801B, 801B Oberdorfer 6620, B6620 Sierra Marine 18-3075 Volvo Penta 831182, 835082, 835182, 875573, 875575 Yanmar 145410-46090   Weight: 0.5 lbs. Od (in/mm): 2 1/4" / 57 Width (in/mm): 1 1/4" / 31.5 Shaft Size (in/mm): 5/8" / 16 Drive Type: Keyway Core Type: Composite Number of Blades: 12 Silhouette Letter: G Fuel Type: Water

Globe Impeller 1112 Globe Impeller Model 1112 Replaces the following impellers Ancor J050021, CEF 500121 Jabsco 22405-0001 Johnson Pump 09-808B, 09-808B-1, 808B Onan 132-0310 Sierra Marine 18-3076 Universal 32620 Vetus IMP 00601 Volvo Penta 833995, 875583, 3586496 Westerbeke 32620   Weight: 0.9 lbs. Od (in/mm): 1 9/16" / 40 Width (in/mm): 3/4" / 19 Shaft Size (in/mm): .47" / 12 Drive Type: Pin Drive Core Type: Brass Number of Blades: 6 Silhouette Letter: B Fuel Type: Water Includes matching Gaskets or O-rings