ATLAS™ 12" Set Back Hydraulic Jack Plate Polished Rated for engines up to 300hp or up to 625 pounds dry weight. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 14" Set Back Hydraulic Jack Plate Polished Rated for engines up to 300hp or up to 625 pounds dry weight. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 4" Set Back Hydraulic Jack Plate STD Polished Rated for engines up to 300hp or up to 625 pounds dry weight. 5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fishermen than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, which was the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy-duty safety cable to protect boaters from engine entering the cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement

ATLAS™ 6" Set Back Hydraulic Jack Plate STD Polished Rated for engines up to 300hp or up to 625 pounds dry weight. Comes with relay harness and rocker switch  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fishermen than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, which was the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy-duty safety cable to protect boaters from engine entering the cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement

G-Force SILENCER Trolling Motor Vibration Pad - Black The G-Force SILENCER™ is a simple trolling motor modification that can help extend the life of your investment and improve function. Custom cut to fit both Motorguide and Minn Kota trolling motor mounts, the G-Force SILENCER™ creates a soft padded surface on your trolling motor mount that eliminates abrasive metal-on-metal contact. In addition to extending the life of trolling motor mounts, the G-Force SILENCER™ also quiets the harsh “clanking” noise associated with pulling your trolling motor out of the water. Protect your investment with the simple and quick addition of the T-H Marine G-Force SILENCER™. Features: Extends life of trolling motor Reduces noise and vibration Eliminates metal-to-metal contact Prevents harsh clanking when stowing trolling motor Package will contain product for Motorguide and Minn Kota WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

G-Force SILENCER Trolling Motor Vibration Pad - Red The G-Force SILENCER™ is a simple trolling motor modification that can help extend the life of your investment and improve function. Custom cut to fit both Motorguide and Minn Kota trolling motor mounts, the G-Force SILENCER™ creates a soft padded surface on your trolling motor mount that eliminates abrasive metal-on-metal contact. In addition to extending the life of trolling motor mounts, the G-Force SILENCER™ also quiets the harsh “clanking” noise associated with pulling your trolling motor out of the water. Protect your investment with the simple and quick addition of the T-H Marine G-Force SILENCER™. Features: Extends life of trolling motor Reduces noise and vibration Eliminates metal-to-metal contact Prevents harsh clanking when stowing trolling motor Package will contain product for Motorguide and Minn Kota WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Steer Stop Outboard Hydraulic Steering Lock Set - 4" T-H Marine developed the first steering stop available for outboard motors and now we've revised that design so it stands apart from imitation and performs better than any other on the market.  With our 4" Steer Stop Outboard Hydraulic Steering Lock in place, boaters can center their outboard motor equipped with hydraulic steering and keep it from wandering when trailering. Similar to the original Steer Stop, units clip onto hydraulic steering rams on either side of outboard to keep engine straight and prevent damage to motor supports. The cord then keeps units together when stowed and aids removal. Additionally, with the new grip built into the design, it is easier than ever to install and remove the Steer Stop Outboard Hydraulic Steering Lock, saving you effort and wear and tear on your hands. Features: Must-know information about the 4" Steer Stop Outboard Hydraulic Steering Lock: Locks hydraulic steering when trailering Fits most steering cylinder rods on outboard engines Snaps over outboards hydraulic steering cylinder rods Helps keep engine centered during transport Protects steering system, outboard, and motor supports Includes cord to connect units for storage and to aid in removal Grip makes it even simpler and easier to put on and take off WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

10" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

12" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - Verado REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

4" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - Verado REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

6" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - Verado REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

8" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - Verado REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

14" Atlas Series Hot Shot™ Jack Plate Hole Shot Plate - Verado REVOLUTIONARY. SIMPLE. UNIQUE. EXCITING. These are but a few of the comments coming from users of T-H Marine's HOT SHOT™ hole shot plates. This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab. An added advantage is the ability to stay on plane and virtually eliminating porpoising at lower speeds. Features: Models available for our ATLAS™ hydraulic jack plates and Z-LOCK™ manual plates.   Models Marked "T" Have side imaging Transducer Cut-Out. Slot fits most Model SI Transducers.  Models to Fit All ATLAS™ Jack Plates (both standard and heavy duty jack plates) Provides Improved Hole Shot Reduces Water Drag at Take Off Reduces Porpoising

G-Force Troll Cable Organizer - Black Neoprene With the patented design of T-H Marine's Troll Jacket, you can protect and manage your trolling motor cables with ease! The G-Force Troll Jacket is a 2mm neoprene trolling motor wire and cable organizer. It measures 60” long and includes a velcro closure. While wrapped, the diameter is about 1.5”. For maximum compatibility for your setup, you can cut and trim the sides where your cables need to come out. This eliminates the need for zip ties along the factory cable cover. It also helps you bundle and organize adjacent wires, like those for your depth finder and HydroWave. Beyond organization, the Troll Jacket prevents exposure of factory cables. If your cables have electrical tape repair, the Troll Jacket gives an additional layer of defense against the elements.

Oetiker Stepless Clamp Kit with Pliers Stepless™ 150-Piece Clamp Rigging Kit by T-H Marine®. This product is made of high-quality materials to serve you for years to come. Designed using state-of-the-art technology and with customers in mind, this product by T-H Marine® will last a lifetime.  Features: Plastic storage case contains 150 stainless steel Oetiker earless clamps, 10 each of 15 popular sizes, plus standard pincer installation tool Oetiker hose clamps with mechanical interlock allows use of pre-coated materials Specially formed strip edges reduce the risk of damage to the part being clamped with uniform compression and increased clamping force All 304 stainless steel bands - Kit includes full size range for all marine hose Includes: (10) 5.8-7MM Ear Clamps (10) 7.8 9.5MM Ear Clamps (10) 8.8-10.5MM Ear Clamps (10) 9.6-11.3MM Ear Clamps (10) 11.5-14MM Ear Clamps (10) 12-14.5MM Ear Clamps (10) 13.2-15.7MM Ear Clamps (10) 14.5-17MM Ear Clamps (10) 15.3-18.5MM Ear Clamps (10) 17.8-21MM Ear Clamps (10) 22.4-25.6 Ear Clamps (10) 26.9-30.1MM Ear Clamps (10) 28.4-31.6MM Ear Clamps (10) 37.8-41MM Ear Clamps (1) Oetiker Jaw Pliers (1) Plastic Tackle Tray