|
RAM Mount No Drill Vehichle System f/Nissan NV1500, NV2500HD, NV3500HD &
Toyota Tundra
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation.
The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens)
The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics.
Compatible Vehicles:
Nissan NV1500 (2011-2021)
Nissan NV2500 HD (2011-2020)
Nissan NV3500 HD (2011-2020)
Toyota Tundra (2007-2021)
Features:
Placement of Mount:
Passenger side, front, where seat rail frame attaches to floor board.
Drilling Requirements:
No - attaches to seat studs
Seat Configuration:
Bucket
Material:
High Strength Composite and Powder Coated Steel
Notes:
If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.
|
311.86 |
|
|
Gunnel Mount Backing Plates f/88502 Outrigger Holder - Pair
Made of heavy gauge stainless steel. Sized for cast outrigger holders only.
|
39.12 |
|
|
Side Mount Backing Plates f/88505 Outrigger Holder - Pair
Made of heavy gauge stainless steel. Sized for cast outrigger holders only.
|
39.12 |
|
|
Large Gunnel Mount Backing Plates f/88506 Outrigger Holder - Pair
Made of heavy gauge stainless steel. Sized for cast outrigger holders only.
|
39.12 |
|
|
Large Side Mount Backing Plates f/88508 Outrigger Holder - Pair
Made of heavy gauge stainless steel. Sized for cast outrigger holders only.
|
39.12 |
|
|
RAM Universal SMALL Tab-Tite Holder for 7" Screen Tablets including the Samsung Galaxy, Dell Streak 7 & BlackBerry PlayBook
Now that you've got the right Tab for the job, you are going to need the right mounting system. Get the most out of your tablet with the Universal RAM Tab-Tite cradle. With 3 sets of interchangeable cup ends, ranging from different sizes and features, you can fit the holder to your tablet for a near custom fit. This spring loaded design makes it easy to load and unload your tablet, along with keeping it secure while on the go. Cup ends are designed to optimize the functionality of your tablet, allowing access to audio jacks, USB, power, and other ports, your tablet can be used just as it was intended. Perfect for stationary or on the go applications, this new RAM product is just what you need to get the most out of your mobile device.
The Tab-Tite is compatible with the following tablets WITH OR WITHOUT SKINS, SLEEVES OR CASES:
Archos 7
Asus EEE Pad Memo
Barnes & Noble NOOKcolor
BlackBerry PlayBook
Dell Streak 7
HTC Flyer
Samsung Galaxy
Included With Purchase:
(1) Spring loaded back plate
(2) Support cups for thin tablets with no skins
(2) Support cups for thin tablets with thin or no skins
(2) Support cups for thick tablets with cases
Mounting hardware
The Tab-Tite cradle is compatible with any tablet that will fit the dimensions listed below. It is important to verify the dimensions of your tablet with a case/sleeve/skin when determining the overall size.
Cradle Dimensions:
Height: 7.3" minimum to 9.62" maximum
Width: Maximum width to 5.31"
Depth: 1.06" maximum
Cradle Dimensions:
Height: 6.80" minimum to 9" maximum
Width: Maximum width to 5.31"
Depth: 0.125" minimum to 0.56" maximum
Cradle Dimensions:
Height: 5" minimum to 9.1" maximum
Width: Maximum width to 4.70"
Depth: 0.125" minimum to 0.44" maximum
Features:
1. Support cups contain open slots to accommodate for tablets of various sizes
2. Back plate can support various size support cups
3. Spring loaded tension provides secure support for your tablet
4. Spring loaded cradle allows for quick release of your tablet
5. Full access to all ports
Material:
High Strength Composite
Note:
The "U" in the part number reflects product packaged in poly bag. Diamond base adapter not included with purchase.
|
31.75 |
|
|
RAM EZ-ROLL'R Cradle f/Apple iPad mini WITHOUT CASE, SKIN OR SLEEVE
The EZ-ROLL'R consists of a high strength composite cradle and patent pending roller design. The patent pending roller design allows for smooth placement and removal of the iPad, while keeping it secure while on the go. Compatible and interchangeable with a wide range of popular RAM Mounting products, this cradle is ready to compliment your iPad and become the most useful accessory in your vehicle.
The EZ-ROLL'R cradle is compatible with the following tablets:
Apple iPad mini WITHOUT CASE, SKIN OR SLEEVE
Specifications:
Docking Cradle: No
Locking Cradle: No
Fits Tablets WITH Cases: No
Fits Tablets WITHOUT Cases: Yes
Low Vibration Environment: Yes
High Vibration Environment: Yes
Cradle Features:
1. Compatible with various iPad cable/docking accessories
2. Patent pending roller design for super smooth placement and removal of the iPad
3. High strength materials maximize longevity of cradle
4. Full access to all ports
5. Lifetime warranty
Material:
High Strength Composite
|
14.36 |
|
|
Tab-Tite™ Cradle for 8" Tablets - Samsung Galaxy Tab 4 8.0 & Tab E 8.0
The RAM® Tab-Tite™ spring loaded, quick release cradle offers a secure fit with easy access to the mounted tablet. The interchangeable cup ends are designed specifically for the Samsung Galaxy Tab 4 8.0, Tab S 8.4, Tab E 8.0 and Tab A 8.0 (2017). The spring loaded design makes it easy to insert and remove your tablet, along with keeping it secure in mobile applications. The custom end cups are designed to optimize the functionality of your tablet, enabling access to all ports and tablet functions.
The included back plate is interchangeable with various size support cups, making it compatible with numerous tablet models. New detachable support cups are the only components needed for purchase, attach to the back plate for support of your new tablet. Included is a set of four nuts and bolts to connect the cradle to any RAM components or mounts that contain the universal AMPs hole pattern.
For off-road environments and extreme use, we recommended the use of a tether to assist in retaining your device. The Tab-Tite™ cradle is compatible with any tablet that will fit the dimensions listed below. It is important to verify the dimensions of your tablet when determining the overall size.
Cradle Dimensions:
Length: 8.08" to 10.69"
Width: 3.77" to 4.96"
Depth: 0.13" to 0.36"
Features:
1. Support cups are designed to offer access to ports and tablet functions
2. Modular design makes upgrading to a new tablet simple and cost effective
3. Dual-spring loaded tension provides secure support for your tablet
4. Easy, quick release of your tablet for on-the-go applications
5. Versatility of cradle allows for attachment to many RAM mounting solutions
6. Lifetime warranty
7. Made in U.S.A.
Material:
High Strength Composite
Note:
The "U" in the part number reflects product packaged in poly bag.
Weight:
0.5 lbs.
|
23.89 |
|
|
Tab-Lock™ Locking Cradle f/Apple iPad mini 1-3 with Case, Skin & Sleeve
The RAM-HOL-TABL12U consists of a spring loaded backplate, custom support cups and locking mechanism for the iPad mini WITH skin, sleeve or case. This spring loaded design makes it easy to load and unload your iPad mini, along with keeping it secure while on the go. Cup ends are designed to optimize the functionality of your tablet, allowing access to audio jacks, usb, power, and other ports, your iPad mini can be used just as it was intended. Quickly lock the cradle, keeping your iPad mini secure and safe from theft. Included is a set of four nuts and bolts to connect the cradle to any RAM components or mounts that contain the universal AMPs hole pattern.
The included back plate is interchangeable with various size support cups, making it compatible with numerous tablet models. New detachable support cups are the only components needed for purchase, attach to the back plate for support of your new tablet.
The Tab-Lock™ cradle is compatible with any tablet that will fit the dimensions listed below. It is important to verify the dimensions of your tablet when determining the overall size.
Cradle Dimensions:
Height: 6.75" to 8.75"
Width: 5.06" to 5.68"
Depth: 0.13" to 1"
Note: Product consists of holder only. Case not included.
Features:
1. Locking mechanism for theft deterrence
2. Support cups contain open slots to accommodate for tablets of various sizes
3. Back plate can support various size support cups
4. Spring loaded tension provides secure support for your tablet
5. Spring loaded cradle allows for quick release of your tablet
6. High strength materials maximize longevity of cradle
7. Full access to all ports
8. Lifetime warranty
Material:
High Strength Composite
Note:
The "U" in the part number reflects product packaged in poly bag. The RAM-HOL-TABL12U is not compatible with the iPad mini 1-3 with LifeProof case.
Weight: 1.15 lbs.
|
63.55 |
|
|
GDS® Locking Vehicle Dock for Apple iPad mini 4
The RAM® vehicle dock with GDS Technology™ is a spring loaded, quick release cradle that offers a secure fit with easy access to the mounted tablet. This docking station is compatible with the Apple iPad mini 4 with IntelliSkin®.
The integrated GDS Technology™ platform enables data and charging capabilities to the mounted tablet. Without the need to remove the IntelliSkin from the device, the user can quickly and efficiently mount the device in the vehicle dock and keep the device charged.
Compatible Devices:
Apple iPad mini with IntelliSkin®
Note: This version of the GDS® vehicle dock is not recommended for light, medium or heavy duty commercial vehicles. For these use cases, please use the RAM-GDS-DOCKL-V2-AP7U.
Features:
GDS Technology™ offers a universal charging platform for any device wrapped in IntelliSkin®
Modular design makes upgrading to a new tablet simple and cost effective
Keyed lock for theft deterrence
Easy, quick release of your tablet for on-the-go applications
Versatility of holder allows for attachment to many RAM mounting solutions
Lifetime warranty, 3 year on electronics
Made in U.S.A.
Specifications:
Max power: 5V-12V @ 2A*
Material: High Strength Composite
Weight: 1.2469 lbs.
*mUSB products supporting USB 2.0/3.0 will have a max current of 1.5A
|
110.12 |
|
|
Double Ball Drill-Down Mount with Diamond Plate & Backer Plate
This mount consists of a 2.5" diameter round base that contains the universal AMPs hole pattern, a long double socket arm, a diamond base adapter, and a backer plate. The mount is designed with a 1-diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm, allowing for almost infinite adjustment and perfect viewing angles.
The hole pattern found on the diamond base adapter will connect to most RAM cradles. The included RAM’s patented design dampens shock and vibration, helping to extend the life of your device.
Specifications:
Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers
Product Dimensions (inch): Overall Height: 7.3125 in.
Socket to Socket Length (inch): 5.31”
Hole Pattern (inch): Diamond Plate: 2-Hole AMPS: 1.912", Round Plate: 4-Hole AMPS: 1.181" x 1.496" & 3-Hole 120-Degree: 1.812" Diameter
Ball Size (inch): B size (1”)
Weight Capacity: The standard use is 2 lbs. and the heavy-duty use is 1 lb.
Materials: Steel, marine-grade aluminum
Weight: 1.0 lb.
|
44.14 |
|
|
Universal Backing Plate Mount with 75x75mm VESA Plate
The mount consists of a double socket arm with one 2.5" diameter round base and one 75mm x 75mm VESA plate, as well as one backer plate. This mount is extremely adjustable and makes a great choice for anyone interested in mounting a device with a VESA hole pattern to a flat surface that can be drilled into.
Specifications:
Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers
Product Dimensions (inch): Overall Height: 7.35"
Socket to Socket Length (inch): 4.66”
Hole Pattern: 75 x 75mm VESA
Plate Size (inch): 3.625" x 3.625"
Ball Size (inch): C size (1.5”)
Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs.
Materials: Marine-grade aluminum
Weight: 1.59 lb.
|
57.71 |
|
|
Backing Plate for 70 Series Rod Holders
Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series.
Features:
Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA)
316L cast stainless steel
4" x 5-1/4"
4mm thick
Use your 1/4" stainless bolts and nuts (hardware not included)
|
25.01 |
|
|
Backing Plate for 80 Series Rod Holders
Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series.
Features:
Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA)
316L cast stainless steel
4-1/4" x 6"
4mm thick
Use your 1/4" stainless bolts and nuts (hardware not included)
|
28.88 |
|
|
Plastic Rod & Cup Holder Backing Plate for Round Rod/Cup Only for 3-3/4" Holes
Threaded Backing Plates for replacing existing ø3-3/4 cup holders with ROUND ABS PLASTIC Combination Rod & Cup Holders. Screws are included.
For use with Round Top ABS Plastic Only in a ø3-3/4 existing hole.
|
5.75 |
|