|
Shock Cord w/Roller (Pair)
Make sure your outrigger halyard lines operate without friction by using the TACO Marine Shock Cord with Pulley. This necessary rigging component provides the tension needed and smooth line movement to deploy baits.
Features:
12" length, Bungee Shock Cord
Smooth roller eye pulley system
Corrosion-resistant clasp
Sold in pairs
1-year limited warranty
|
31.24 |
|
|
C-Cleat Cam Cleat - Large - Grey w/Grey Base
6-16mm(1/4" - 5/8") Rope Diameter
Intensive development efforts have produced this range of cleats that provide unbeatable holding power, yet are designed for easy cleating and releasing of control lines in every application and load condition. Through the use of advanced composites, these cleats achieve superior performance while overcoming the limitations of metal alloys. Ronstan cam cleats are strong, light and corrosion free. The unique tooth profile and cam geometry are designed to grip without damaging the rope. A multi-coil spring recessed in the upper part of the cam generates near constant torque. This constant torque ensures secure cleating of even the smallest lines with minimal abrasion or rope wear and low line entry and exit efforts. The lightweight ultra rigid carbon fiber composite cams of the c-cleat are corrosion free, suffer virtually no tooth wear and are non rope abrasive.
Features:
Design, materials selection and advanced manufacturing methods combine to deliver superior strength and holding power, light weight and corrosion resistance
Cam profile and multi-coil spring minimise line entry and release effort
Carbon fiber compoasite cam material provides maximum resistance to heat and abrasion
Unique self-cleaning, self-lubricating slotted bearings ensure consistent high performance even when subjected to high static loads
Applications:
Range of cleats for all requirements including control lines, jib sheet and mainsheet cleating
Materials:
Carbon fiber composite cams
Long strand glass fiber reinforced polymer base
PTFE impregnated Acetal slotted bearing
Stainless steel multi-coil spring
|
42.34 |
|
|
NXL-M4 Full Range 4 Channel IPX5 Marine Grade Amplifier - 150 x 4W @ 4-Ohm
Designed for intense sessions that keep the party boat rocking all night long; the NXL-M4 is DS18’s high-quality, powerful amplifier for the wave runner looking for a big sound with a small footprint!
As a Class D Digital amplifier, the NXL-M4 uses a direct insert speaker and power terminals significantly smaller than your average amplifier, making it the perfect size for any vehicle’s custom build: but, what it lacks in size it makes up for in power.
The NXL-M4 handles 150W x 4CH @ 4 Ohms; 230W x 4CH @ 2 Ohms; and 440W x 2CH @ 4 Ohms Bridge of RMS Power and 1800W Peak Power.
Get clean, well-defined sound for with enough features (Fully Variable Bass Boost, Low Pass Filter, and High Pass Filter) to tune your music perfectly for optimal audio enjoyment! This full-range amplifier handles all speakers insanely well and has the features to make sure they play the way you want them to!
This amplifier is tough enough to stand up to the worst the waves throw at you! All controls are guarded by high-strength front covers that guarantee impenetrable defense against the elements; coated 4-layer PCB helps prevent corrosion caused by salt water; and Voltage, Thermal, and Short Circuit Protection for easy monitoring of your power levels.
Order the NXL-M4 for insane power out on the water!
Features:
Hardware resistant to corrosion and UV Protection
Coated 4 Layers PCB to prevent corrosion
IPX5 Water Resistance Grade
High Level Input For Radio Use
Front cover to keep the controls safe to the elements
LED Clip Indicator to easier adjustment
Stable and Reliable Class D Circuit Design
Sound Quality Verification Using AP Instruments
Direct Insert Power and Speaker Terminals
Short Circuit, Thermal, and Voltage Protection
Technical Specifications:
Number of Channels - 4
Frequency Response - 20Hz - 20KHz
2 Ohm RMS Power Per Channel - 4 x 230W
4 Ohm RMS Power Per Channel - 4 x 150W
4 Ohm RMS Power Bridge Channel - 2 x 440W
Signal-to-Noise Ratio - >90dB
Product Dimensions: (L x W x H) - 9.6" x 4.5" x 1.7"
*Sold as an Individual
|
479.94 |
|
|
C-Cleat Cam Cleat - Medium - Grey w/Grey Base
3-12mm(1/8" - 1/2") Rope Diameter
Intensive development efforts have produced this range of cleats that provide unbeatable holding power, yet are designed for easy cleating and releasing of control lines in every application and load condition. Through the use of advanced composites, these cleats achieve superior performance while overcoming the limitations of metal alloys. Ronstan cam cleats are strong, light and corrosion free. The unique tooth profile and cam geometry are designed to grip without damaging the rope. A multi-coil spring recessed in the upper part of the cam generates near constant torque. This constant torque ensures secure cleating of even the smallest lines with minimal abrasion or rope wear and low line entry and exit efforts. The lightweight ultra rigid carbon fiber composite cams of the c-cleat are corrosion free, suffer virtually no tooth wear and are non rope abrasive.
Features:
Design, materials selection and advanced manufacturing methods combine to deliver superior strength and holding power, light weight and corrosion resistance
Cam profile and multi-coil spring minimise line entry and release effort
Carbon fiber compoasite cam material provides maximum resistance to heat and abrasion
Unique self-cleaning, self-lubricating slotted bearings ensure consistent high performance even when subjected to high static loads
Applications:
Range of cleats for all requirements including control lines, jib sheet and mainsheet cleating
Materials:
Carbon fiber composite cams
Long strand glass fiber reinforced polymer base
PTFE impregnated Acetal slotted bearing
Stainless steel multi-coil spring
|
23.36 |
|
|
Waterproof Universal Bluetooth Streaming Audio Receiver w/Controller & Microphone
Take your marine audio experience to the next level with DS18’s BTRCRMIC – an audio streamer designed to provide crystal-clear sound, no matter what the weather conditions may be!
Featuring a CB radio-style microphone with controls, the BTRCRMIC allows you to communicate through your audio system. The CB Radio Style Mic is plugged in via the included quick-detach cable. While using the mix, you can control your background audio’s volume with a few easy clicks. The red LED on the microphone also aids in understanding the available functions.
The BTRCRMIC’s easy-to-use blue back-lit silicon buttons make it effortless to operate. It's also built with a wireless BT audio receiver with BT 5.0v for long-range streaming up to 130ft*, allowing you to listen to your favorite tunes with ease. DS18’s BTRCRMIC also comes with a stereo 2.5v pre-out RCA, and remote output to control the external amplifier, and can be used as a stand-alone source unit/receiver.
Its USB port for music and charging (1A), an aux audio input using a 3.5mm jack, mic/handset controller input, RCA line output for an external amplifier, and remote output for an external amplifier, make this product applicable in any build.
The integrated power wiring harness ensures that your device is always protected with overload and power protection circuitry, while the IPX6 water resistance rating ensures that your device is protected from water damage, making it perfect for all elements.
Whether you're cruising on the open road or exploring the open sea, DS18’s BTRCRMIC has got you covered!
Features:
One-hole design for easy installation
CB Radio style Microphone with controls
IPX6 Water resistance rating
USB port to Play your favorite music or re-charge your devices
Built-in Wireless BT Audio Receiver
BT 5.0v for long range up to 130ft*
5mm jack auxiliary audio input
Stereo 2.5v Pre-out RCA
Remote output to control external amplifier
Use it as a stand-alone source unit/receiver
Easy-to-use blue back-lit silicon buttons
Integrated Power Wiring Harness
Overload & Power Protection Circuitry
Technical Specifications:
Frequency Response - 20Hz-20KHz
Signal to Noise Ratio - >80dB
Channel Separation - >60dB
Voltage Operation - DC 10-15V
Fuse Size - 5 Amp
Wireless Range - >130 ft (conditions may vary)
USB Player Capacity - < 32GB
Measurements - 3.7" (Dia.) x 2.44" (D)
Mounting Depth - 1.85"
Mounting Hole Size - 2.87"
*Sold as an Individual
|
179.94 |
|
|
Performance Poly-Guard Crew/4-Seater UTV Cover - Grey
*Measurements - 150" x 60" x 74"
All Carver Powersport UTV covers are available in long-lasting outdoor performance quality materials.
Features:
Fit-Specific for UTVs. Available in 3 sizes for the best fit possible.
Heavy Duty Elastic 1/4″ Shock Cord encased in the hem for a snug fit.
Cover comes standard with the following:
2 – heavy duty tie-down straps
Easy Installation Instructions
Available in three fabrics: Sun-DURA® - Black (7-Year Warranty), Performance Poly-Guard®(5-Year Warranty) and Camouflage - Mossy Oak® Break Up Country (5-Year Warranty)
Performance Poly-Guard®
Excellent Quality
100% Marine-grade polyester. Highest tear strength available. 8 oz, strong and durable. UV and mildew resistant. Excellent resistance to fading. Extremely water-resistant w/ durable water repellent, anti-fungal & anti-microbial finish. Breathable to help allow interior moisture to escape. Made in USA. (5 Year Limited Warranty)
Design:
Construction - Join seams are folded four-ply. No raw edges
Stitching - Double stitch construction for added strength and durability
Weather Resistant - Anti-wick thread throughout construction
Best Warranty in the business based on fabric selection
All Carver Covers are made in the USA
|
209.63 |
|
|
1-1/2" Wide Keel Base Roller Assembly f/2" - 2-1/2" Tongue
Product Description
This roller assembly supports your boat's keel for easy loading and safe transport on your trailer. It features a 4", black rubber spool roller and a galvanized steel bracket that attaches to your trailer's tongue. 2 to 2-1/2" trailer tongue.
Features:
Spool roller supports your boat's keel as it sits on the trailer
Prevents the bow from making contact with your winch
Eases loading and unloading of boat
Helps to absorb road shock while boat is being trailered
Bracket lets you bolt roller assembly onto the tongue or frame of your boat trailer
Requires 7/16" fasteners (not included)
Sturdy, 1/8" galvanized steel bracket resists corrosion
Black rubber roller delivers long-lasting performance
Made in USA
Specifications:
Roller length: 4"
Shaft diameter: 5/8"
Diameter of mounting holes (each): 7/16"
Spacing of mounting holes: 3" apart on center
Typically installed flat on the tongue of a boat trailer, this spool roller bracket assembly stabilizes the keel of the boat during trailering.
|
27.46 |
|
|
Flip-Up Polyethylene Roto Molded 4-Step Dock Ladder - Grey
Tough and durable, this roto-molded ladder swings up and out of the way, locking in place when not in use. Will not corrode with exposure and will not fade or crack. Molded-in U.V. inhibitors and fungicides.
Rail Height: 20-1/2" above the dock
Distance to first step: From dock surface, 11-3/4" & 10-1/2" between steps
Steps: Are 4" deep and 14" wide
Capacity: 500 lb (227 kg)
|
239.60 |
|
|
Stand-Off Flip-Up Polyethylene Roto Molded 4-Step Dock Ladder - Grey
Tough and durable, this roto-molded ladder swings up and out of the way, locking in place when not in use. The Stand Off roto-molded ladder extends into the water at a 60 degree angle to make getting out of the water easier. Will not corrode with exposure and will not fade or crack. Molded-in U.V. inhibitors and fungicides.
Rail Height: 20-1/2" above the dock
Distance to first step: From dock surface, 12-1/2" & 10-1/2" between steps
Steps: Are 6-1/2" deep and 14" wide
Capacity: 500lb (227 kg)
|
261.54 |
|
|
Chain Grip - For 10mm Chain - 3/8" - 103mm Length - 4-1/16"
Features:
For a 10mm chain
Perfect for ensuring safe anchoring by easing the tension on the anchor chain
Protects the boat by reducing the chafe of the chain on the rub rail and roller chock
Positioned between two links of the chain (single-handed operation)
Optimized design to avoid accidental release of the chain
One piece with nonmoving parts
Forged in Duplex stainless steel grade (increased mechanical & corrosion resistance)
Applications:
Mooring
Specifications:
Materials: Duplex stainless steel grade
Dimensions:
Rope size: (mm) 22
Length: (inch) 4 1/16" / (mm) 103
Working load: (lb) 1580 / (kg) 720
Breaking load: (lb) 2820 / (kg) 1280
Weight: (lb) 0.344 / (g) 156
Caption:
Working Load (WL): For nautical applications
Working Load Limit (WLL): For industrial applications only. The safety factor is 5 times the breaking load. WLL = Breaking load / 5
*Sold as an Individual
|
77.24 |
|
|
1.5" Track Ball w/ T-Bolt Attachement
Designed to accommodate all kayak tracks, as well as common track systems, engage and fasten this base to your existing track system or many other's including GearTrac, SlideTrax and the common T-Track. With a quick turn of the ball the base will slide along the track, giving you ultimate flexibility in repositioning your rod holder. A necessity for the all fishing enthusiasts, the RAM Track Base is certain to create more mounting options or access on whatever you choose to take to the water.
Compatible Tracks: YakAttack GearTrac, Wilderness Systems SlideTrax, Most Common T-Tracks Scotty Slide Track, Many More!
|
14.41 |
|
|
1" Fresh Water Strainer w/#304 SS Basket
Features:
Protect fresh water pumps from debris.
White nylon strainer head and clear plastic sight glass. Glass unscrews for filter basket cleaning.
Mount bracket included.
Use WSB for fresh-water systems (#304 SS basket)
|
60.67 |
|
|
2-1/2" Copper Coupling w/Stop Double Press Connection - Smart Connect Technology
Features:
For use with ASTM B88 and B75 tubing
Copper
Press connection
Components:
EPDM sealing elements
*Note - Must be installed with Viega ProPress XL-C rings and V2 actuator.
|
78.95 |
|
|
ProPress 1/2" Copper Coupling w/o Stop - Double Press Connection - Smart Connect Technology
Features:
For use with ASTM B88 tubing
Copper
Press connection
Components:
EPDM sealing elements
|
7.48 |
|
|
2-1/2" Copper Coupling w/o Stop - Double Press Connection - Smart Connect Technology
Features:
For use with ASTM B88 and B75 tubing
Copper
Press connection
Components:
EPDM sealing elements
*Note - Must be installed with Viega ProPress XL-C rings and V2 actuator.
|
80.02 |
|