|
Flotec FP4032-10MK Overhaul Kit
Flotec Overhaul Kit for Flotec FP4032-10, Includes Seal Plate, Seal Plate O-Ring, Seal, Impeller, Priming Baffle, Nozzle/Diffuser Assembly, Nozzle O-Ring
This Kit Does Not Fit The FP4032-08 Pump.
Flotec, Simer and Sta-Rite parts are interchangeable. The Brand name does not matter, only the part number must be the same.
|
216.23 |
|
|
Flotec FP400C Sewage Pump System - 4/10 HP
Economical sewage pump system manufactured of durable thermoplastic construction. Ideal for basement installations, pumping below-grade toilets, and laundry facilities.
KEY FEATURES
Maximum pumping capacities up to 5250 GPH
Corrosion-resistant construction with multi-vane, non-clog vortex impeller
Grommets accept 4" PVC inlet, 2" PVC discharge and vent
Handles up to 2" solids
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: thermoplastic pump / structural foam basin
HORSEPOWER: 4/10
MAXIMUM CAPACITY: 5250 GPH
FLOW AT 10' LIFT: 2550 GPH
SWITCH TYPE: Tethered
DISCHARGE PIPE SIZE: 2"
MINIMUM PIPE SIZE: 2"
MAXIMUM SOLID HANDLING SIZE: 2"
CORD LENGTH: 8'
AMP DRAW: 18.5 amps
VOLTAGE: 115v, 60 Hz
|
784.08 |
|
|
Flotec FP4105 Cast Iron Jet Pump 1/2 HP
New cast iron shallow well jet pump is ideal for wells with pumping levels of 25' or less. Self-priming after the pump housing is initially filled with water.
KEY FEATURES
Reliable performance at 25' depth to water or less
Maximum pressures of 63 PSI and maximum pumping capacities to 5.1 GPM
Pump housing is constructed of heavy-duty cast iron and is ready to install
115 volt 1/2 HP
Fan cooled, completely enclosed motor
1" Suction Port and 1" Discharge Port
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 5.6 GPM
FLOW at 10' LIFT and 40 PSI: 4.5 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 63 PSI
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 7.2 amps
VOLTAGE: 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
381.42 |
|
|
FP4432 Overhaul Kit
Use for Flotec model FP4432 deep well jet pump
Includes impeller, diffuser, and all needed seals and gaskets
Restores like-new performance
|
160.16 |
|
|
Flotec FP2122 Submersible Well Pump 4"
Flotec Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 3/4HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required
|
650.30 |
|
|
March TE-6T-MD-3PH 3/4HP WEG Poly Glass Pmp W/3Ph 3/4Hp
|
954.90 |
|
|
Amt 3890-10M36Jt Brz Self Prime 3/4Hp Pump
|
1322.36 |
|
|
Goulds Lsp0711Atf 3/4Hp Sump Pump 1/60/115V
Goulds- Submersible Sump Pump Plastic with Stainless Steel Motor Casing LSP Series, 57GPM at 10' Head, 1 1/2”FNPT Discharge, 115V 60HZ 3/4HP 1Phase, Piggyback Wide Angle Float Switch, 20' Cord
|
568.75 |
|
|
Goulds Lsp0711F 3/4Hp 1/60/115 Sump Pump
Goulds- Submersible Sump Pump Plastic with Stainless Steel Motor Casing LSP Series, 57GPM at 10' Head, 1 1/2”FNPT Discharge, 115V 60HZ 3/4HP 1Phase, Manual Operation - No Float Switch, 20' Cord
|
508.60 |
|
|
Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP
This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less.
KEY FEATURES
Perfect for shallow wells (depth-to-water less than 25')
Thermoplastic construction for higher corrosion resistance
1-1/4" Suction / 1" Discharge
Comes with pre-wired 30/50 pressure switch
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8 GPM
FLOW at 10' LIFT and 40 PSI: 6.4 GPM
MAX LIFT: 25'
MAX PRESSURE: 77 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DISCHARGE PIPE SIZE: 1" NPT
AMP DRAW (full load): 9.4 amps
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
432.90 |
|
|
Scot Pump 48372X-3/4HP MPU 72 1PH 3/4HP 4 IMP ODP
Pump
Seawater Bronze case, impeller, adapter
Seawater Bronze 7/8 inch shaft
Mechanical seal is 7/8 inch diameter
Impeller is keyed to stub shaft and secured by a washer and locking assembly.
O-Ring case gasket
Motor – 2 Pole
Standard NEMA frame motor
|
1606.50 |
|
|
Scot Pump 48451X-3/4HP MPU 3/4HP 1PH 56C
Pump
• Seawater Bronze case, impeller adapter
• Seawater Bronze 7/8” shaft
• Impeller keyed to stub shaft and secured by washer and locking assembly
• O-ring case gasket
Motor
• Standard NEMA frame motor
• 1 and 3 phase
|
1854.36 |
|
|
Burks T37G5-1 1/4-SS-3.25, Centrifugal Pump
80gpm, 1-1/4" Outlet 3/4HP 3PH
|
5122.39 |
|
|
Flotec FP4112 Cast Iron Shallow Well Jet Pump 1/2 HP
Cast iron shallow well jet pumps provide superior performance and high capacities with more pressure for shallow wells 25' or less.
KEY FEATURES
Superior performance at depths to water of 25' or less
Rugged, heavy-duty cast iron pump housing
Ready-to-install dual voltage (115v/230v) motor
1-1/4" NPT suction and 1" NPT discharge pipe sizes
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 8.8 GPM
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM
MAX PSI: 56 psi
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
MINIMUM SUCTION PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.4 amps
VOLTAGE: 115v/230v (preset to 115v), 60 Hz
RECOMMENDED BREAKER: 15 amp
LIQUID TEMP RANGE: 32°F-140 °F (0°C-60 °C)
JET KIT: included
|
433.55 |
|
|
Flotec FP4212 Cast Iron Convertible Jet Pump 1/2 HP
KEY FEATURES
Superior performance at depths to water of 100' or less
Rugged, heavy-duty pump housing
Ready-to-install dual-voltage 115v/230v motor - see manual for 230 volt conversion
Pressure switch pre-wired with 30-50 PSI pressure setting
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Cast Iron
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 7.9 GPM (shallow setup)
FLOW at 10' LIFT and 40 PSI: 7.1 GPM (shallow setup)
MAX LIFT: 25' for shallow setup / 70' for deep setup
MAXIMUM PRESSURE: 60 psi (shallow setup) / 54 psi (deep setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4" NPT
DRIVE PIPE SIZE: 1" NPT
DISCHARGE PIPE SIZE: 1"NPT
AMP DRAW (full load): 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
509.25 |
|