CPT-70 Plastic Thru Hull Transducer Urethane Through Hull Transducer with Fairing Block. The CPT-70 requires A80332 Adapter Cable (if you have a green locking collar on the unit.) Features Plastic Thru Hull Max Depth: DV=600ft/FF=900ft Beam Width: 25°/60° Depth and Temperature Cable Length: 33ft/10M Deadrise: 0-25°

CPT-110 Plastic Thru-Hull Transducer for CP100 Sonar Module Contains two elements, one for the conical beam CHIRP sonar (center frequency 200kHz) the other for the DownVision CHIRP sonar (center frequency 350kHZ) Contains a temperture sensor 10M Cable

GT15M-IH Plastic, In-Hull, Mid-Band CHIRP Transducer - 85-165kHz, 600W, 8-Pin GT15M-IH transducer is ideal for boats that want to install the transducer inside a fiberglass hull and not on the transom where cavitation could cause issues. It can be used with a hull deadrise angle between 0 and 25 degrees and is excellent for boats traveling at high speeds that want to maintain accurate depth readings. The 8-pin transducer with 4 plastic tanks features mid-band CHIRP traditional sonar (85-165 kHz) and has a power rating of 600 W. It can be used in conjunction with a GT30-TM transducer and an adapter cable so you can maintain depth at high speeds and scanning capabilities at trolling speeds. For installation, follow the included instructions carefully to avoid damaging your boat. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XPTH 9 20 MSI T MEGA Plastic Thru-Hull Transducer MEGA SI, MEGA DI, DualBeam PLUS, 20/60/86/55 degrees, 200/83/455/800 kHz and 1.2 MHz. Temperature built-in, plastic through the hull transducer. 30' cable Transducer dimensions:  7.34"L x 3"W Shaft diameter:  1.0" WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XPTH-9-HW-MSI-T MEGA SI+/DI+ Dual Spectrum CHIRP Plastic Thru-Hull Transducer with Temp  MEGA Side Imaging+ Plastic Thru-Hull Transducer supports MEGA Imaging/800kHz/455kHz and Dual Spectrum CHIRP 2D Sonar with a CHIRP range of 150-220kHz. Includes built-in temperature sensor, rugged composite design and 30’ cable.  Features: This accessory is compatible with the following Humminbird products: HELIX 8 CHIRP MEGA SI+ GPS G3N, HELIX 9 CHIRP MEGA SI+ GPS G3N, HELIX 10 CHIRP MEGA SI+ GPS G3N, HELIX 12 CHIRP MEGA SI+ GPS G3N. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHRIP Max Depth: 1200ft (365m) MEGA Side Imaging+ Frequencies - Max Range (side-to-side): 455kHz: 440-500 kHz - 800ft (244m), 800kHz: 790-850 kHz - 250ft (76m), MEGA SI+: 1075-1150 kHz - 400ft (m) MEGA Down Imaging+ Frequencies - Max Depth: 455kHz: 440-500 kHz - 400ft (122m), 800kHz: 790-850 kHz - 125ft (38m), MEGA DI+: 1075-1150 kHz - 200ft (61m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XPTH 14 HW MSI T Plastic Thru Hull Transducer SOLIX MEGA Side Imaging+, MEGA Down Imaging+, Dual Spectrum CHIRP plastic thru hull transducer. This transducer supports MEGA Imaging+/800kHz/455kHz and Dual Spectrum CHIRP 2D Sonar with a CHIRP range of 150-220kHz. Includes built-in temperature sensor, rugged composite design and 30’ cable.  Features: This accessory is compatible with the following Humminbird products: SOLIX 10 CHIRP MEGA SI+ GPS G2, SOLIX 12 CHIRP MEGA SI+ GPS G2, SOLIX 15 CHIRP MEGA SI+ GPS G2 MEGA Side Imaging Frequencies - Max Range (side-to-side): 455kHz: 440-500 kHz - 800ft (244m), 800kHz: 790-850 kHz - 250ft (76m), MEGA SI+: 1075-1150 kHz - 400ft (122m) MEGA Down Imaging Frequencies - Max Depth: 455kHz: 440-500 kHz - 400ft (122m), 800kHz: 790-850 kHz - 250ft (76m), MEGA DI+: 1075-1150 kHz - 200ft (61m) Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHIRP Max Depth: 1200ft (365m) Dimensions: L 8.4" x W 2.3" x D 1.0" - Stem Length 5", Stem Diameter 1" 1-Year Limited Warranty

P79 In-Hull Transducer w/Humminbird #9 Plug - 7-Pin Our P79 in-hull transducer easily adjusts to hull dead rise angles up to 22º. This ensures that the beam is vertically oriented to receive echoes, resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance. Features: Adjusts to hull deadrise angles from 2° to 22° No holes to drill Depth only Recommended for solid fiberglass hulls Adheres to aluminum hulls under 3.8 mm (0.16") thick Recommended for planing-hull power boats, trailered boats, rigid inflatable boats (RIBS), and racing sailboats No hull protrusions Boat Size: Up to 8M (25') Specifications: Weight: 2.3kg (5lb) Hull Deadrise: 0° to 22°   Acoustic Window: Layered plastic urethane This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Our P79 in-hull transducer easily adjusts to hull deadrise angles up to 22'. This ensures that the beam is vertically oriented to receive echos resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance. Works with the Lowrance HDS Series and Simrad NSE Series Multifuction Display units. Features Depth 50/200 kHz 600 W RMS Mid-performance Plastic 7 Pin Blue Connector

M265LH Plastic In-Hull Mount Transducer w/Depth - 12-Pin Garmn's best performing 1 kW in-hull, this narrow beam transducer provides crisp image detail. The transducer has a depth of 3,000 feet; an operating frequency of 42 to 65 kHz and 130 to 210 kHz; a beamwidth of 16 to 25 degrees or 6 to 10 degrees; and a 0 to 30 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. *Not recommended for cored-hull vessels Compatible Devices: GPSMAP® 7607xsv, 7608xsv, 7610xsv, 7612xsv, 7616xsv GSD™ 25 Premium Sonar Module WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RV-320 Plastic Thru-Hull Transducer Pack with 20° Deadrise Compensation Designed for inboard or outboard boats, the RV-320 Plastic Through Hull Transducer System lets you easily identify structures and locate fish with the life-like clarity of RealVision 3D™ sonar. The RV-320 system is a 4-channel, Wide Spectrum CHIRP transducer system with DownVision™, SideVision™, high frequency CHIRP fish targeting and RealVision 3D™ sonar inside. The transducer system has a built-in attitude and heading reference system (AHRS) that stabilizes the sonar imagery, automatically compensating for vessel motion. You’ll enjoy crystal-clear imagery in waves, swells, and while maneuvering. The RV-320 system also has a built-in fast response water temperature sensor for quick, accurate readings. Raymarine’s RV-320 Plastic Through Hull Transducer system pack contains a pair of RealVision 3D transducers with internal offset to accommodate hull deadrise angles from 14° to 26°. This completely eliminates the need for fairing blocks. The low-profile design slips effortlessly through the water without causing drag or cavitation. The near-flush RV-320 system works even works great on trailered boats. The RV-320 system features rugged plastic through hull bodies suitable for fiberglass, steel or aluminum hulls. One transducer transmits and receives to port and downwards, the other to starboard and downwards, ensuring a full 180° of underwater coverage even on boats with deep keels or other underwater protrusions. Each transducer features a 2-meter pigtail, joining y-cable and 8-meter extension cable, resulting in an overall cable length of 10 meters (33 feet.) In the Box: RV-320P Plastic Port Transducer with 2-meter cable RV-320S Plastic Starboard Transducer with 2-meter cable RealVision 3D Transducer Y-Cable RealVision 3D 8-meter (26-feet) Transducer Extension Cable Anti-rotation bolt kit Installation instructions

xSonic M135M Medium Chirp 1 kW In-Hull Transducer - 9-Pin The M135M’s medium frequency delivers the right combination of coverage under the boat, an extended depth range, and the ability to produce clean and accurate target and structure returns in mid- to deeper water. Medium frequency also delivers excellent shallow to mid-depth performance, bottom detail, and fish-target separation. Operating at a frequency range of 85 to 135 kHz, this transducer reveals fish at medium depths up to 457 m (1500 ft) and gives ultra-clear target resolution. Airmar’s M135M includes a plastic mounting base that is aligned with the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. The eco-friendly coolant is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is that there are no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 11 m (36') with a solid fiberglass hull. Features: Depth only 1 kW of power 50 kHz of total bandwidth from one transducer Recommended for use on planing and displacement hulls Plastic transducer and mounting base Covers popular fishing frequencies of 88 and 107 kHz plus everything else in the bandwidth Also available as transom (TM185M), thru-hull low-profile (B175M), and thru-hull with fairing (B285M) mounts Patented Xducer ID® technology Specifications: Medium frequency: 85 to 135 kHz Beamwidth: 16 degrees to 11 degrees Maximum Depth: 457 m (1500 ft.) Weight: 4.2 kg (9.2 lb.) Recommended Boat Length: Up to 11 m (36 ft.) Hull Material: Solid fiberglass only Hull Deadrise: Up to 22 degrees Acoustic Window: Urethane Transducer Element: One broadband ceramic assembly Includes: Adjustable mounting base This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

P79 Adjustable In Hull Transducer 50/200kHz with 6-Pin Features: In Hull Transducer Plastic Adjustable 6-Pin WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

xSonic SS175H-W/12 Stainless Steel Thru-Hull Transducer - 12° - 9-Pin The SS175H-W is a stainless steel, thru-hull CHIRP transducer, ideal for sportfishing and commercial vessels up to 8M (25') in size. This single-channel transducer offers High CHIRP combined with a wide beam for the best resolution and coverage in shallower depths.  Features: 130-210 kHz High CHIRP with wide 25° beam for excellent fish targets  Up to 310M (1000') range with High CHIRP 1 internal broadband ceramic Thru-hull with stainless steel housing Suitable for fiberglass and wood hulls Ideal for sportfishing and commercial vessels up to 8M (25') Recommended for use with Simrad NSSevo3 Lowrance HDS Gen3 multifunction displays

SS175H-W/0 Stainless Steel Thru-Hull Transducer - 0° - 9-Pin The SS175H-W is a stainless steel, thru-hull CHIRP transducer, ideal for sportfishing and commercial vessels up to 8M (25') in size. This single-channel transducer offers High CHIRP combined with a wide beam for the best resolution and coverage in shallower depths. Features: 130-210 kHz High CHIRP with wide 25° beam for excellent fish targets  Up to 310M (1000') range with High CHIRP 1 internal broadband ceramic Thru-hull with stainless steel housing Suitable for fiberglass and wood hulls Ideal for sportfishing and commercial vessels up to 8M (25') Recommended for use with Simrad NSSevo3 Lowrance HDS Gen3 multifunction displays

XPTH-9-HW-T Dual Spectrum CHIRP Plastic Thru-Hull Transducer with Temp  Plastic Thru-Hull Dual Spectrum CHIRP Transducer supports Dual Spectrum CHIRP 2D Sonar with high frequency beam and wide cone angle, offering CHIRP range of 150-220kHz and max depth of 1200ft. Includes built-in temperature sensor, rugged composite design and 30’ cable.  Features: This accessory is compatible with the following Humminbird products: HELIX 5 CHIRP G2 – GPS-equipped models only, HELIX 7 CHIRP G2/G3 – GPS-equipped and CHIRP DI G2 models, HELIX 7 CHIRP G2N/G3N – All models, HELIX 8 CHIRP G3N – All models, HELIX 9 CHIRP G2N/G3N – All models, HELIX 10 CHIRP G2N/G3N – All models, HELIX 12 CHIRP G2N/G3N – All models, ICE HELIX CHIRP G2 – All models (In Open Water Mode). Side Imaging™ and Down Imaging™ units can support the XPTH 9 HW T as a 2D sonar only transducer. This transducer does not support Side Imaging or Down Imaging. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHRIP Max Depth: 1200ft (365m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.