|
El Outboard Steering Kit for Up To 150HP Motors
401 Manual Helm with Fitting Kit
The heart of the Admiral Series is the HyDrive M402 helm unit. The 7-piston pumps are precision manufactured to standards and tolerances that are second to none. In-built lock valves, which eliminate torque feedback are standard. The light, smooth steering must be experienced to be appreciated. Designed as a complete Do It Yourself installation, everything you need is supplied including detailed instructions. You don’t even have to know anything about hydraulics!
The Admiral Series 401 helm units offer improved internal efficiencies and unique assembly design, consolidating HyDrive Engineering‘s position as a world leader in hydraulic boat steering. Two years of design development and testing have resulted in these helms being selected as the standard helm supplied in all HyDrive steering kits.
Features:
Front-mount design for maximum appeal
Improved internal efficiency
Brass wheel nut and washer
Stainless steel steering wheel shaft - not aluminum
Anti-splash filler cap for rough conditions
Unique assembly design for ease of service and maximum performance
Stainless steel studs, nuts, and washer pre-fitted for convenience
Highly efficient non-return valves for non-feedback of helm unit - eliminates all torque from the steering cylinder
Ultra 15 Oil Quantity 2 - 1 Liter Bottles
Features:
For use in HyDrive Skipper and Admiral Series Hydraulic steering systems only
Not for use in HyDrive 2000 Series Steering Systems
This oil is compatible with HyDrive HF15, but should not be mixed with any other fluids
N-8 - 49' Nylon Tube 3/8"
Features:
Semi-Rigid Nylon Tube at 3/8 Inch OD (49' Coil, You Cut to length to suit)
Use with HP Compression Olive and Nut Fittings
Supplied in HY EL O/B KIT
Stainless Steel Tube & Rod for Up To 150HP Up To 150HP Outboard
Specifications:
Cylinder Tube = Stainless Steel
Cylinder Tube Dia. = 1.33 Inches
Cylinder Rod = Stainless Steel
Cylinder Brackets = Stainless Steel
Cylinder 1 " Nylok Nuts = Stainless Steel
Cylinder End Caps = Cast Aluminum
Cylinder Rod Stroke = 7-1/2 Inches
Cylinder Type = Un Balanced Cylinder
Cylinder Volume Big Side Vol = 155 ccSmall side Vol = 115 cc
Steering Wheel HO/HO = 5.5 and 4.1 Turns
Total length Rod Compressed = 15.75 Inches
Rod Extended = 23.00 Inches
Cylinder Total Weight = 3.15 Pounds (1427 Grams)
|
1399.44 |
|
|
HYCO 1.1T Front Mount OB Tilt Steering up to 150HP
The Hyco 1.1T With Tilt Hydraulic Steering Kit is all you need for a complete steering system. This system is used on all engines up to 150HP or less. If engine H/P exceeds 150 then the Protech packaged system must be used.
Package Kit Includes:
1-UP20T Tilt Helm Pump
UC95-OBF/1 Front mount Hydraulic Cylinder
2 quarts of Oil-15 Hydraulic Oil
Installation and Instructions manual included
*Premade Hose Kit 2' to 30' ft. length is not included and steering wheel not included.
Please Note:
There are two Cylinders offered, the UC95-OBF/3 model is for Honda BF115 and BF130 engines and Mercury Optimax 75, 90, and 115 HP engines only, and the UC95-OBF/1 is used on all other O/B models.
|
1121.46 |
|
|
HYTECH 1.1 Front Mount OB System up to 175HP - Includes UP20 FM Helm, 2qts of Oil, UC95-OBF Cylinder & 40' Tubing
The HYTECH steering kit featuring the unique split tilt tube rod that allows for installation of the UC94 cylinder without removing the engine. The HYTECH is an easy and affordable outboard hydraulic steering solution for boats with 175 horsepower and under. Coupled with the composite UP20 helm, the HYTECH offers effortless steering with 5 turns lock to lock. And, it is applicable to almost all 2 and 4 stroke outboard engines.
Kit Contains:
UP20 FM Helm
UC95-OBF cylinder
OIL 15 - 2 Quarts
40' of cut to length tubing
|
833.09 |
|
|
HYCO 1.1 Front Mount OB System up to 175HP - Includes UP20 FM Helm, 2qts of Oil, UC95-OBF Cylinder
Featuring the unique split tilt tube rod that allows for installation of the UC94 cylinder without removing the engine, the Hyco is an easy and affordable outboard hydraulic steering solution for boats with 150 horsepower and under. Coupled with the composite UP20 helm, the Hyco offers effortless steering with 5 turns lock to lock. And, it is applicable to almost all 2 and 4 stoke outboards engines.
Kit Contains:
UP20 FM Helm
UC95-OBF cylinder
OIL 15 - 2 Quarts
|
817.70 |
|
|
NAC-1 Outboard Hydraulic Autopilot Pack
Features:
Easy to Install, available for both Hydraulic and Cable steer systems
Dash-mount button for one-touch Auto/Standby activation
Steer to Heading, Course, or Route
Automatic Turn Patters
NAC-1 Plug & Socket connectors – no screw terminals or wire stripping necessary
High efficiency, super-quiet 0.8L hydraulic gear pump (Pump-1 MKII)
Add a second Helm station to a boat using the MFD Power steer commands – no need for additional hydraulics + steering wheel
In the Box:
Point-1 AP Heading and GPS Sensor 000-12930-002
NAC-1 Autopilot Computer 000-11769-001
PUMP-1 MKII – 0.8L reversible hydraulic pump 000-11770-002
Hydraulic fitting kit 000-15942-001
Standby-Auto button 000-13703-001
Micro-C Network Components:
N2KEXT-2RD,CABLE,MICRO-C, 0,6M - 000-0119-88
N2KEXT-6RD,CABLE,MICRO-C, 1,8M - 000-0127-53
N2KEXT-15RD,CABLE,MICRO-C, 4,5M - 000-0119-86
TR-120-KIT - 000-0127-52
MICRO-C POWER CABLE ONLY - NO T CONN - 000-12202-001
N2K,MICRO-C,4-WAY BLOCK (22AWG) - 000-12612-001
|
1438.80 |
|
|
Lowrance Outboard Cable-Steer Pilot Pack
Everything you need in one box to fit an autopilot to your outboard motor, the Outboard Pilot lets you focus on fishing activity while keeping the boat on course.
When connected to a Lowrance HDS Gen2 or Gen2 Touch, the Outboard Pilot can steer to a waypoint or along a route, select a turn pattern or simply hold a constant heading.
The Lowrance SmartSteer™ user interface allows you to easily switch between electric-steer, trolling-motor control and outboard motor control directly from your HDS display. And, with your HDS display, you can easily convert trails to routes - so you can retrace a previous track and get your boat back to the dock from your fishing area.
HDS Units require 3.5 Software
Steer your outboard motor to a heading, waypoint, route or cursor, with control from your HDS Gen2 or Gen2 Touch display
Lowrance SmartSteer™ interface provides control of your cable-steered outboard motor, as well as the MotorGuide Xi5 Pinpoint electric-steer trolling motor
"One-touch" route creation from trails
Pre-set turn patterns for more effective fishing/trolling presentations
Recommended for single-outboard setups, on boats that are 30 feet and less, in length
VRF (Virtual Rudder Feedback).simplifies pilot installation eliminating the need for a rudder position sensor
Easy setup.straightforward guide steps you through first-time install
Easy-to-install, plug-and-socket connection with no complex terminal wiring
Supported by Lowrance Advantage Service program
Dash-mount button for one-touch Auto/Standby activation
Steer to Heading, Course or Route
High efficiency, super-quiet 0.8L hydraulic gear pump
Lowrance Outboard Pilot Cable-Steer Pack replaces the manual helm-drive unit
Morse 290, Morse 304411 and Teleflex SSC52 cable compatibility
Helm-1 is only compatible with the NAC-1.Helm-1 includes variable-voltage feedback interface
2 Year Limited Warranty
Package Includes:
NAC-1 Autopilot Computer - 000-11769-001
The brains behind the Lowrance Outboard Pilot system. It contains the steering computer and electronics for the drive unit motor and clutch.
Helm-1 for Outboard Pilot - 000-11771-001
This drive unit replaces your manual helm-drive unit on single cable installations. Compatible with Morse 290, 304411 and Teleflex SSC52 cables. Includes voltage rudder-feedback sensor, and is only compatible with NAC-1.
N2K 4 Way - 000-10996-001
NMEA2000 4-way joiner. Connect four NMEA2000 Micro-C devices to the NMEA2000 Network.
N2KEXT-2RD - 000-0119-88
0.6M (2') NMEA 2000® cable for backbone extension or or drop cable to connect an additional network device
N2KEXT-6RD - 000-0127-53
1.82M (6') NMEA 2000® cable for backbone extension or drop cable to connect an additional network device
N2KEXT-15RD - 000-0119-86
4.55M (15') NMEA 2000® cable for backbone extension or or drop cable to connect an additional network device
TR-120-KIT - 000-0127-52
Set of 1 male and 1 female NMEA 2000® terminators
MICRO-C POWER CABLE ONLY - NO T CONN - 000-12202-001
|
1738.80 |
|
|
For use with Adjustable Tie Bars on standard Dometic steering cylinders. Allows the consumer to take full advantage of all the features and benefits of the heavy-duty adjustable tie bar products for twin engine applications up to 600 HP. Utilizes Tournament series adjustable tie bars. High strength, forged aluminum. Eliminates need for cut-to-length traditional tie bars.
|
229.99 |
|
|
For use with Adjustable Tie Bars on standard Dometic steering cylinders. Allows the consumer to take full advantage of all the features and benefits of the heavy-duty adjustable tie bar products for twin engine applications up to 600 HP. Utilizes Tournament series adjustable tie bars. High strength, forged aluminum. Eliminates need for cut-to-length traditional tie bars.
|
238.99 |
|
|
Boat Leveler to Bennett Actuator Conversion Kit - Hydraulic to Hydraulic
Bennett Marine's V351CK conversion kit replaces Boat Leveler cylinders with Bennett though-hull fittings.
Kit includes:
2 hydraulic cylinders and all hardware to convert your system
2 stainless steel conversion brackets
8 1/4-20 x 1/2 machine screws
4 1/4-20 x 3/4 wood screws
2 3" pipe nipples
2 female barb fittings
2 actuators
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
212.60 |
|
|
Stainless Steel Tube & Rod for Up To 150HP Up To 150HP Outboard
Specifications:
Cylinder Tube = Stainless Steel
Cylinder Tube Dia. = 1.33 Inches
Cylinder Rod = Stainless Steel
Cylinder Brackets = Stainless Steel
Cylinder 1 " Nylok Nuts = Stainless Steel
Cylinder End Caps = Cast Aluminum
Cylinder Rod Stroke = 7-1/2 Inches
Cylinder Type = Un Balanced Cylinder
Cylinder Volume Big Side Vol = 155 ccSmall side Vol = 115 cc
Steering Wheel HO/HO = 5.5 and 4.1 Turns
Total length Rod Compressed = 15.75 Inches
Rod Extended = 23.00 Inches
Cylinder Total Weight = 3.15 Pounds (1427 Grams)
|
239.99 |
|
|
Repair kits for Baystar hydraulic cylinders.
|
149.99 |
|
|
Repair parts for SeaStar hydraulic cylinders.
|
77.99 |
|
|
Repair parts for SeaStar hydraulic cylinders.
|
29.99 |
|
|
Repair kits for SeaStar hydraulic cylinders.
|
148.99 |
|
|
Repair kits for SeaStar hydraulic cylinders.
|
89.99 |
|