Oberdorfer 109MB Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 1 1/4" NPT Outlet: 1" NPT Flow: 80 GPM Max Pressure: to 19 PSI, 45 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS Oberdorfer™ centrifugal pumps have a single rotating metal impeller. Liquid enters at the center and is thrown outward radially by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient, pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently a relief valve is not required. The liquid flow varies directly as the pump speed—the higher the speed the greater the flow. Horsepower required varies directly as flow and pressure. Maximum horsepower is required with a wide open discharge line. This is the point of maximum flow. With a throttled discharge, the flow decreases at a greater rate than the pressure increases thereby requiring less horsepower at the higher pressures. This is known as an “unloading” feature of the pump. FEATURES Rugged Bronze Construction A Standard in the Marine Air Conditioning Industry Extremely Quiet Operation O-Ring Housing seal eliminates gasket problems Polytetrafluoroethylene (PTFE) Barrier Seal to protect motor bearings Handles Contaminated Liquids Discharge port orientation flexibility-8 positions Mechanical Seal - Carbon/Ceramic, Nitrile - standard, Fluoroelastomer (S10) optional, Polytetrafluoroethylene (PTFE)(S11) optional Pump Heads mount to standard footed Nema 56J Jet Pump Motors Shafts: 416 Stainless, Nickel Alloy, or 316 Passivated Stainless Multiple motor options available For Industrial Version - see Model 700 series DRIVE This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. Single phase motors are nonreversible and are wired for the proper pump rotation which is counter-clockwise looking at the inlet end of the pump. (See the dimensional drawing.) Three phase motors must be checked out for proper rotation when the pump is installed.  Interchanging of any 2 wires in a 3-phase system will reverse motor rotation.  LIQUIDS & TEMPERATURES The special pump alloys used provide corrosion resistance to many liquids including water, water solutions, and a wide range of commercial chemicals. Questions as to the chemical compatibility of special liquids should be referred to the factory. The pump uses a mechanical type shaft seal with a Nitrile rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212oF and 75 P.S.I. Fluoroelastomer (S10) seals and Polytetrafluoroethylene (PTFE) (S11) seals are available for severe solvents and difficult chemicals. Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids as compared with water, a reduction in flow and pressure occurs and the required horsepower rate increases.  Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity. Liquids contaminated with small solids or abrasives can be handled, but a reduction in mechanical seal life must be expected.  SUCTION LIFT These centrifugal pumps are not self-priming. They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction). However, if a foot valve is used at the beginning of the suction line and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet. Such a system relies entirely on a non-leaking foot valve for starting capability.   Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.     109MB is Oberdorfers - Centrifugal Pump Head Only Bronze 1 1/4" X 1"NPT  

Jabsco 11870-0007 Electric Clutch Pump 32V Pump Body: Bronze Port Size: 1-1/4" NPT Internal Electric: 32V Pulley: Single B groove or Double A groove Impeller: Nitrile Shaft Seal: Mechanical Carbon-Ceramic, Face Type Shaft: Stainless Steel Bearings: Shielded Ball Bearings   APPLICATIONS This electrically activated clutch pump offers all the benefits of flexible impeller pumps with a substantial flow rate and horizontally oriented ports. The electric clutch offers convenient remote activation.   MARINE: Pumping bilges, Washdowns, Circulating water in bait tanks, Utility dock-side pump.   INDUSTRIAL: Circulating and transferring, Velocity mixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals,   Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning Liquors, Glycerine, Brine, etc.   FARMING: Pumping water stock, Pumping water from shallow wells and cisterns.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, Cesspools, Sumps, Water heaters and water closets, Drains and sinks, Draining fishponds and pools.   PUBLIC UTILITIES AND MUNICIPALITIES: Under the hood mounting on service trucks for draining meter boxes, manholes, excavations; For pollution control and watering for dust control.   Jabsco Electric Clutch Pump 32V, 1-1/4" NPT Ports, Double "A" Groove Pulley  

Jabsco 30540-0000 Pedestal Pump 316SS   Pump Body: 316 Stainless Steel Pedestal Pump Port Size: 2" NPT Internal Flow: Nominal 105 USgallons/min at 1750rpm Pressure: Pressure up to 1.5 bar Impeller: Neoprene, Nitrile, Viton or EPDM Shaft Seal: Mechanical; Carbon-on-Ceramic, or Tungsten Carbide; Nitrile or Viton Shaft: 316 Stainless Steel     APPLICATIONS Easy to service and maintain. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Non pulsating flow. Self-priming from dry up to 2.4m (7.8ft).   INDUSTRIAL: Circulating and transferring, velocity-mixing, pumping machine tool coolants, spill return, sump drainage, chemicals, pharmaceuticals, soap, liquors, ink, dyes, alcohol, dilute acids, tanning liquors, glycerine, brine, etc. PHARMACEUTICAL: Processing medicines, lotions and preparations. Filtering pharmaceutical solutions.Filling line supply pump. PAPER PROCESSING: Transferring and applying starches, sizes, etc. Circulating and processing wood pulp slurries. FOOD, BEVERAGE & DAIRY: Transfer brines, vinegar, syrups during processing, liquids containing solids in suspension such as chopped tomatoes, nuts, etc. Removal of distillery wort and brewery slop. Processing viscous materials such as peanut butter, mayonnaise, ketchup, honey, etc. (low speed). Pumping whiskey, wine, rums, juices and ciders. AGRICULTURAL: Transferring liquid fertilizers, herbicides and pesticides   Jabsco Pedestal Pump 316SS 2" NPT Std Pressure Nitrile Impeller Carbon Seal

Jabsco 31820-0494 Series Industrial Diaphragm Pump Pump Body: Glass Filled Polypropylene, Four Piston, Diaphragm Pump Port Size: Snap-in 1/2" (13 mm) Hose Barb and 1/2" (13 mm) Straight Pipe Thread Flow: 3 GPM/12 LPM Pressure: Continuous, Maximum 40 psi (2.8 bar) at Ambient of 130° F (54.4° C). No Switch. Elastomers: Santoprene Diaphragm, Valves of Viton Motor: Commercial Duty, Permanent Magnet with Thermal Overload Protection. Corrosion Protected. Conforms to Electromagnetic Compatibility 89/336/EEC and Machinery Directive 89/392/EEC, EN50081-1     APPLICATIONS Self-Priming to 10 ft. (3 m). Runs Dry Without Damage. Smooth Flow. Snap-in Ports.   CONSTRUCTION: Water supply pump to the spray bars of road rollers and other compaction equipment, street sweepers, and truck mounted dust control systems.   AGRICULTURAL: Supply pump for herbicide and pesticide spraying equipment.   INDUSTRIAL: Fluid transfer applications for mild acids and bases. Chemical feed pump. Washing fluid supply pump in parts washing systems. Machine coolant pump. Concrete saw lubricant supply pump. Recirculating pump in filtering systems.   Jabsco Industrial Diaphragm Pump 24V 3GPM No Switch  

Jabsco Flexible Impeller Pedestal Pump Eng Cooling Pump   FEATURES Pump Body: Brass, Low Profile Verson Port Size: 3/8" BSP or 3/8" NPT Flow: Nominal 10 Litres/min (2.2 gallons/min) at 1500rpm Impeller: Neoprene Shaft Seal: Carbon/Ceramic Mechanical Shaft: Stainless Steel 12mm     APPLICATIONS / CHARACTERISTICS Marine: Engine Cooling, Bilge Pumping, Water Circulation.     Industrial: Circulating and Transferring, Velocity Mixing.   Farming: Pumping Water for Stock, Liquid Ballast Transfer.   Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. Self-priming from dry up to 1.5m (4.9ft).   Jabsco Flexible Impeller Pedestal Pump 3/8" NPT Low Profile

Jabsco Flexible Impeller Pedestal Pump   FEATURES Pump Body: Brass, High Profile Verson Port Size: 3/8" BSP or 3/8" NPT Flow: Nominal 10 Litres/min (2.2 gallons/min) at 1500rpm Impeller: Neoprene Shaft Seal: Carbon/Ceramic Mechanical Shaft: Stainless Steel 12mm     APPLICATIONS / CHARACTERISTICS Marine: Engine Cooling, Bilge Pumping, Water Circulation.   Industrial: Circulating and Transferring, Velocity Mixing.   Farming: Pumping Water for Stock, Liquid Ballast Transfer.   Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. Self-priming from dry up to 1.5m (4.9ft).     Jabsco Flexible Impeller Pedestal Pump 3/8" NPT High Profile  

MP Pumps 21311 Flomax 5, 1-1/2" pedestal mount self priming pump  MP Pumps Flomax 5, rated at 100 GPM in bronze construction with viton mechanical seal.   Specifications Rated Capacity 100 GPM Maximum Discharge Pressure: 40 PSI Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT Construction: Bronze housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8"; viton mechanical seal.

MP Pumps 34741 FRX50 Series 316 Stainless Steel 12V DC Circulator 1/2 " NPT Pump   MP Pumps FRX50 Stainless Steel Circulator Pump # 34741. Ideal for Marine, Industrial and Commercial, Flows about 12.5 GPM, pressures 16.5 feet head, 3/4" suction & discharge, 316 stainless steel construction.   Specifications Construction: Stainless steel Housing and Cover, 304 Stainless Steel Base with viton O-rings, 316 stainless steel impeller semi open (sintered PM).  Mechanical Seal: carbon/ceramic/viton bellows  Motor: 12 Volt DC.  Suction & Discharge Connections: 1/2" NPT, 1" Hose  

Walbro FRC-8-2 Industrial 12V Fuel Pump 12Psi   Industrial Reciprocating Fuel Pump Genuine Walbro Part # FRC-8-2 12 Volt Up to 12 PSI    Voltage: 12 Volt (9.0 min - 16.0 vdc max) Minimum Flow Rate: 106 liters per hour (28 gph) Deadhead Pressure: 62 to 83 kPa (9.0 to 12.0 psi) Maximum Current Draw: 2.3 ampsLife: >8,000 hours Dry Lift: 48 inches Compatible Fuels: No-lead regular gasoline, premium gasoline, gasoline-alcohol blends, diesel and biodiesel fuels (20% and 100%), and E85 Corrosion Resistance: 96 hour salt spray test (ASTM B-117)Operating Temperature Range: -40ºF to 155ºF (-40ºC to 68.3ºC)   Electrical Reverse Voltage Protected Transient Voltage Protection Ground: Circuit Board is Internally Grounded to Pump Body Electrical Connector: Packard Electric (Accepts mating connector 12015782) Fuse: 5 amp recommended   Mechanical Inlet & Outlet Size: 1/8-27 NPSF Inlet Filter Screen: 70 micron Magnetic Trap Standard Outlet Check Valve: Yes 20 micron Filter Screen   The FRC series fuel pump is designed to supply fuel for internal combustion engine applications only. It is not intended or designed for continuous operation applications such as heater or stove systems.  

Jabsco 12490 Series Self Priming Stainless Steel Pump FEATURES Pump Body: 316 Stainless Steel Port Size: 1" NPT internal Flow: 26.0 GPM at 10 feet of head Pressure: Up to 26 PSI Impeller: Neoprene or Nitrile Shaft Seal: Lip Type in Stainless Steel Case Shaft: Steel motor shaft with special Stainless Steel sleeve. Motor: 3/4 HP, 1725 RPM, 60 Hz Single Phase, 115/230 Vac, Continuous Duty, Totally Enclosed Fan Cooled, 56 Frame, Capacitor Start. Thermal Overload Protection with Automatic Reset, Carrying Handle, 6' Cord with 3 Prong Grounded Plug.     APPLICATIONS / CHARACTERISTICS CHEMICAL - Industrial Motor Pump Unit Circulating, Transferring and Filtering of Chemicals, Plating Solutions, Pharmaceuticals, cosmetics and Farm Chemicals, Emptying and Filling Carboys, Vats, Tanks, Barrels or Entire Systems.    Jabsco Self Priming Stainless Steel Pump 1" NPT Ports 3/4HP Motor Nitrile Impeller  

Oil Change Bucket Kit - With Gear Pump Gear Pump Oil Change Bucket 12V Features:  Reliable, well designed & proven gear pump technology For marine or industrial applications Portable & convenient High temperature resistant dipstick tube Heavy-duty alligator clips easily clamp directly onto battery Use the easy pour spout to empty used oil in recycling container 12 Volt 1 Year Warranty Kit includes: Pail Sealed Lid Pump Assembly Dipstick tube Heavy Duty Alligator Clips Easy Pour Spout

MP Pumps 21339 Flomax 8 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 8 Part # MP 21339 Configuration: Pedestal Mount Port Size: 2 in. NPT Flow-Rate: 150 GPM Head Feet: 100   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial   Marine    

MP Pumps Flomax 5 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 5 Part # MP 21302 Port Size: 1 1/2 in. NPT Flow-Rate: 145 GPM Head Feet: 100   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

MP Pumps 21327 Flomax 8 Self Priming Centrifugal Pump FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 8 part # MP 21327 Port Size: 2 in NPT Flow-Rate: 150 GPM Head Feet: 100     Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine  

Micropump GA-T23.J9FS.A Pump Head A Mount The GA Series high-performance pumps provide precise and pulseless flows. Featuring Micropump's suction-shoe design, GA Series pumps self-compensate for wear, ensuring near zero slip and a longer pump life. Pumps are available in a wide range of materials and configurations. Feature: Small Size Smooth, Pulseless Delivery Chemically Resistant Easy to Service Proven Reliability Advanced Pump Technology Wide Range of Options OEM Configurations Enhanced Efficiency Pump Series: GA Series Ports/Fittings: 1/8-27 (F) NPT Side Ports Min Speed (RPM): 500 Max Speed (RPM): 5500 Max Pressure (psi): 300 Min Temperature (°C): -46 Max Temperature (°C): 177 Max Diff. Pressure (psi): 75 Displacement (ml/rev): 0.092 Design: Standard Design Gear Set: 0.125/2/40 (0.092 ml/rev) Gear Material: PEEK (hex drive) Static Seals: PTFE Base Materials: 316SS Drive Mount: MP Housing Bypass: No Driven: Ferrite Driving Magnet: Not Included High System Pressure: No Bushings: None Shafts: 316SS Gear TrimNone Model: GA-T23.J9FS.A