Galaxy 5225-XT 8' VHF Antenna - 6dB Gain - Reduced Length EXTRA TOUGH! Shakespeare's best 8', 6dB Gain antenna. Its Galaxy® design maximizes range and quality in a great looking antenna. The 5225-XT is Shakespeare's classic Style 5225 in a new, stronger, sturdier, stiffer radome for extra duty. It's extra tough for use on hard tops, T-tops, radar arches, or wherever its extra resistance to high winds and high speeds is welcome. Features: Collinear-phased 5/8 wave elements Brass and copper elements for maximum range and efficiency Stainless steel ferrule with standard 1"-14 thread 20' RG-8/X low-loss cable plus a PL-259 connector Suggested mount: Shakespeare Style 4187 Ratchet Mount One section Shakespeare Limited Warranty: 5 years Includes FME cables Technical Specifications: Gain: 6dB Frequency: VHF Marine Band Bandwidth: 3 MHz within 2.0:1 VSWR SWR: Nominally 1.5:1 at 156.8 MHz Impedance: 50 ohms Max Input (Watts): 100 watts DC Ground: YES Polarization: Vertical

Shakespeare Style 5206-N VHF Marine - Reduced Length Version 8' LENGTH 6dB END-FED WITH MATCHING STUB Same as the Style 5206-C, but the 5206-N has a nylon ferrule. An economical and lightweight, self-supporting antenna for good communications where range is not the predominant factor. Quality copper cable elements for good range and efficiency Nylon ferrule with standard 1"-14 thread Includes 15' RG-58 cable and a PL-259 connector Suggested mount: Shakespeare Style 495 Lift-n-Lay Mount or Style 4186 Ratchet Mount Twin to: Shakespeare Styles 5205 and 5207 CB Marine antennas One section Shakespeare Limited Warranty: 2 years Technical Specifications: Frequency: VHF Marine band Bandwidth: 3 MHz SWR: 1.5:1 @156.8 MHz Impedance: (Ohms): 50 Gain: 6 dB Max Input (Watts): 50 DC Ground: NO - the antenna will read "open circuit" when checked with an ohm meter or continuity tester. Termination: RG-58 Height (feet): 8 Polarization: Vertical Radiation pattern: Omni-directional

6018-R Phase III VHF Antenna - 17′ 6″ (5.3M) VHF Marine Band 9dB Gain  Good communication over the VHF Marine Band depends on antenna height, quality and dB Gain. This high performing Phase III™ marine antenna is a powerhouse providing all of those necessities in our rugged, high-strength, foam-filled fiberglass radome for stability in high seas, high winds and high speeds. Features: Silver-plated outer conductor, copper inner conductor • Stainless steel mounting sleeve • Type SO-239 connector inside mounting sleeve for easy mounting and dismounting for stowage • Suggested mount: Shakespeare® Style 409-R or 410-R Mounting Kit • Two sections: Base 110″, Tip 110″ Specifications: Design: Collinear-phased 1/2-wave elements with choking sleeve  Height: 18' (5.48m) Weight: 20lbs (9kg) Gain: 8dB Connector Type: SO-239 Suggested Mounting: 409-R or 410-R Impedance: 50 ohms Max Input Power: 150W DC Grounding: No Shakespeare Limited Warranty: 8 years

6500-WB 4FT Broad Band VHF Antenna 3dB Built for maximum performance, this 4’ broad band antenna is designed to endure the harsh environment and communication requirements in commercial, law enforcement and disaster management applications. Whether you install it on a vessel, base station, or a stationary platform, this antenna provides a host of mounting options to fit your need. No tuning or ground plane required. Cable not included. Features: Stainless steel mounting bracket: corrosion resistant even in marine environments. Patent pending mount design: install the U-bolts without removing hardware – no more lost hardware Detachable antenna: handle mounting bracket easily without the weight of the antenna. Mount it on a large variety of Shakespeare® mounts with a 1”-14 thread* IP67**, high wind rating, wide temperature range, and PU Coating: built to last in rain, sun, ice, dust, water splashes and even corrosive marine environments *Requires a Shakespeare 4006 double female ferrule (not included). **When installed as instructed.

5400-XT Galaxy 4' VHF Antenna - 3dB Gain The compact Galaxy® 5400-XT is an outstanding, general purpose 4' antenna of heavy duty construction for general purpose communications. Its at home on T-tops, hard-tops, and other positions aloft, where its small size can deliver maximum range. Features: Center-fed 1/2 wave coaxial sleeve Brass and copper elements for maximum range Stainless steel ferrule with standard 1"-14 thread Includes 20' RG-8/X cable and a PL-259 connector Suggested mount: Shakespeare Style 4187 Ratchet Mount One section Shakespeare Limited Warranty: 5 years Includes FME Cables Technical Specifications: Frequency: VHF Marine Band Bandwidth: 5 MHz within 2.0:1 VSWR SWR: Nominally 1.5:1 at 156.8 MHz Gain: 3 dB Max Input (Watts): 50 watts Height (feet): 4

B924 Class B AIS Transceiver with WiFi, Bluetooth & VHF Antenna Splitter - 2W CSTDMA **As the FCC requires all units sold in the US to be programmed by a qualified technician. Please submit the form below for programming at the time of purchase. A copy of the MMSI registration or FCC Ship Station License is required along with the vessel master or owner's signature on the completed programming form.** Click here to download form. The most feature-rich 2W CSTDMA AIS transceiver in the B900 range. The B924 includes WiFi & Bluetooth for seamless wireless connectivity and AIS data streaming to any mobile device, PC, or wearable, with an integrated VHF antenna splitter to enable your transceiver to share your existing VHF antenna without any loss of performance. Like all B900 transceivers, it also includes an integrated next-generation GPS receiver and antenna and is designed for em-trak's unique FLEXI-FIT® bracket system to make installation as easy as possible. Exceptionally lightweight and completely weatherproof, the B924 delivers the very best (2W) AIS receive and transmit performance, so you see all AIS information and targets, even at maximum range. Your transceiver will also work with our CONNECT-AIS mobile phone app to make programming, configuration, and transceiver health monitoring simple and convenient. Features: Certified AIS Class B – 2W CSTDMA Integrated WiFi and Bluetooth Integrated VHF antenna splitter Global certification - USCG / FCC / Canada / Europe SRT-AIS™ Transceiver Engine for superlative proven performance FLEXI-FIT™ bracket system for easy, convenient, and secure installation Internal high-performance GPS receiver and antenna (external antenna optional) Water, pressure spray, and damp proof (IPx6, IPx7 certified) Protected from vibration, shock, and extreme temperatures Small and lightweight Ultra-low power consumption – best in class Guaranteed connectivity and interoperability with any app, chart plotter, smartphone, tablet, or PC NMEA 0183 & NMEA 2000 Automated health and performance monitoring Silent mode (transmit-off) function Enhanced RF screening to protect against electromagnetic interference Built-in power surge protection Physical & Environmental Specifications: Size (H x W x D): 150 x 115 x 45mm Weight: 425kg Operating temperature: -25°C to +55°C Storage temperature: -25°C to +70°C Ingress protection: IPx6 and IPx7 Electrical Specifications: Supply voltage: 12V or 24V DC Supply voltage range: 9.6V - 31.2V DC Average current (at 12V): 280mA Average current (at 12V) (wireless off): 245mA Peak current: 2A Average power consumption (at 12V): 3.4W Average power consumption (at 12V) (wireless off): 2.9W Galvanic isolation: NMEA 0183 inputs only, NMEA 2000, VHF antenna port Connectors: VHF antenna: SO-239 VHF radio: SO-239 GNSS: TNC Power: 12-way circular multipole NMEA 2000: 5-way Micro-C connector USB: USB Micro-B Data Interfaces: NMEA 0183: 2 x bi-directional ports NMEA 2000: NMEA 2000 Ed 3.101, LEN=1 USB: PC virtual com port for NMEA 0183 data WiFi: IEEE 802.11 (a/b/g), client and access point mode supported (2 connections in access point mode) Bluetooth: BT Classic 4.0, 7 concurrent connections Standards Compliance: AIS standards: IEC 62287-1 Ed. 3, ITU-R M.1371.5 Product safety standards: EN60950-1 2006 +A11:2009 +A1:2010 +A12:2011 +A2:2013 EN62311:2008 Environmental standards: IEC 60945 Ed. 4 Serial data interface standards: IEC 61162-1 Ed 5.0, IEC 61162-2 Ed 1.0 NMEA 2000: NMEA 2000 Ed 3.101 GNSS performance standards: IEC 61108-1 Ed 2.0, IEC 61108-02 Ed 1.0 GNSS: Systems supported: GPS, GLONASS, BeiDou, Galileo (two of any combination, three including GPS, Galileo) Channels: 72 Internal/external antenna: Internal or optional external antenna Time to first fix from the cold start: 26s VHF Transceiver: VDL access scheme: CSTDMA Operating frequency: 156.025MHz - 162.025MHz Channel bandwidth: 25kHz Receivers/transmitters: 2 x receivers, 1 x transmitter AIS receiver sensitivity (20% PER): -111dBm AIS transmitter power: 2W (+33dBm) User Interface: Indicators: Power, transmit timeout, error, silent mode In the Box: 1 x AIS transceiver 1 x Power and data cable (2M) 1 x VHF radio accessory cable 1 x FLEXI-FIT™ mounting bracket Complete with screws & optional fixing tape

B954 Class B AIS Transceiver - 5W SOTDMA with WiFi, Bluetooth, & VHF Antenna Splitter **As the FCC requires all units sold in the US to be programmed by a qualified technician. Please submit the form below for programming at the time of purchase. A copy of the MMSI registration or FCC Ship Station License is required along with the vessel master or owner's signature on the completed programming form.** Click here to download form. The B954 is the most feature-rich high transmit power (5W SOTDMA) AIS transceiver in the B900 range. The B954 combines Wi-Fi & Bluetooth for seamless wireless connectivity and AIS data streaming to any mobile device, PC or wearable, with an integrated VHF antenna splitter to enable your transceiver to share your existing VHF antenna without any loss of performance. Like all B900 transceivers, it also includes an integrated next-generation GPS receiver and antenna and is designed for em-trak's unique FLEXI-FIT® bracket system to make installation as easy as possible. Lightweight and completely weatherproof, the B954 delivers the very best AIS receive and transmit performance with increased range and transmission priority. Your transceiver will also work with our CONNECT-AIS mobile phone app to make programming, configuration, and transceiver health monitoring simple and convenient. Features: Certified AIS Class B – 5W SOTDMA Integrated WiFi and Bluetooth Integrated VHF antenna splitter Global certification - USCG / FCC / Canada / Europe SRT-AIS™ Transceiver Engine for superlative proven performance FLEXI-FIT™ bracket system for easy, convenient, and secure installation Internal high-performance GPS receiver and antenna (external antenna optional) Water, pressure spray, and damp proof (IPx6, IPx7 certified) Protected from vibration, shock, and extreme temperatures Small and lightweight Ultra-low power consumption – best in class Guaranteed connectivity and interoperability with any app, chart plotter, smartphone, tablet, or PC NMEA 0183 & NMEA 2000 Automated health and performance monitoring Silent mode (transmit-off) function Enhanced RF screening to protect against electromagnetic interference Built-in power surge protection Fail-safe VHF radio operation Physical & Environmental Specifications: Size (H x W x D): 150 x 115 x 45mm Weight: 425kg Operating temperature: -25°C to +55°C Storage temperature: -25°C to +70°C Ingress protection: IPx6 and IPx7 Electrical Specifications: Supply voltage: 12V or 24V DC Supply voltage range: 9.6V - 31.2V DC Average current (at 12V): 280mA Average current (at 12V) (wireless off): 245mA Peak current: 2.5A Average power consumption (at 12V): 3.4W Average power consumption (at 12V) (wireless off): 2.9W Galvanic isolation: NMEA 0183 inputs only, NMEA 2000, VHF antenna port Connectors: VHF antenna: SO-239 VHF radio: SO-239 GNSS: TNC Power: 12-way circular multipole NMEA 2000: 5-way Micro-C connector USB: USB Micro-B Data Interfaces: NMEA 0183: 2 x bi-directional ports NMEA 2000: NMEA 2000 Ed 3.101, LEN=1 USB: PC virtual com port for NMEA 0183 data Wi-Fi: IEEE 802.11 (a/b/g), client and access point mode supported (2 connections in access point mode) Bluetooth: BT Classic 4.0, 7 concurrent connections Standards Compliance: AIS standards: IEC 62287-2 Ed. 2, ITU-R M.1371.5 Product safety standards: EN60950-1 2006 +A11:2009 +A1:2010 +A12:2011 +A2:2013 EN62311:2008 Environmental standards: IEC 60945 Ed. 4 Serial data interface standards: IEC 61162-1 Ed 5.0, IEC 61162-2 Ed 1.0 NMEA 2000: NMEA 2000 Ed 3.101 GNSS performance standards: IEC 61108-1 Ed 2.0, IEC 61108-02 Ed 1.0 GNSS: Systems supported: GPS, GLONASS, BeiDou, Galileo (two of any combination, three including GPS, Galileo) Channels: 72 Internal/external antenna: Internal or optional external antenna Time to first fix from the cold start: 26s VHF Transceiver: VDL access scheme: SOTDMA Operating frequency: 156.025MHz - 162.025MHz Channel bandwidth: 25kHz Receivers/transmitters: 2 x receivers, 1 x transmitter AIS receiver sensitivity (20% PER): -111dBm AIS transmitter power: 5W (+37dBm) User Interface: Indicators: Power, transmit timeout, error, silent mode In the Box: 1 x AIS transceiver 1 x Power and data cable (2M) 1 x VHF radio accessory cable 1 x FLEXI-FIT™ mounting bracket Complete with screws & optional fixing tape

Galaxy 5018 15' 2” VHF Antenna - 6dB Gain This highly sophisticated design is outstanding for long distance communications. Extra rugged for salt water durability, and stability in high seas. Surprisingly light weight.  Features: Phased 1/2 wave elements in a collinear array with choking sleeve to suppress cable radiation Brass and copper elements for maximum range and efficiency Stainless steel ferrule with standard 1"-14 thread 20' RG-8/X low-loss cable plus a PL-259 connector Suggested Mount: Shakespeare Style 409-R or 410-R Mounting Kit (pictured mount not included) Two sectiions 5 Year Warranty Technical Specifications: Gain: 9dB Frequency: VHF Marine Band Bandwidth: (within 2.0:1 VSWR) 3 MHz SWR: 1.5:1 at 156.8 MHz Max Input (Watts): 150W DC Ground: NO Height (Feet): 15'2" Polarization: Vertical

5309-R 23' Galaxy VHF Antenna - 9dB Gain THIS PRODUCT MUST SHIP TRUCK FREIGHT AND DOES NOT QUALIFY FOR ANY SHIPPING PROMOTIONS This design invokes all the antenna engineers tricks to produce the clearest possible transmission and reception over the longest range. Features: Phased 1/2 wave elements in collinear array with a band spread matching sleeve and a choking stub to suppress cable radiation Brass and copper elements Stainless steel ferrule with standard 1"-14 thread Includes 20' RG-8/X cable and a PL-259 connector Suggested mount: Shakespeare Style 409-R or 410-R Mounting Kit (pictured mount not included) Two sections: Base 172", Tip 105" Twin to: Galaxy Style 5310-A HF/SSB Shakespeare Limited Warranty: 5 years Includes FME Cables Technical Specifications: Frequency: VHF Marine Band Bandwidth: 5 MHz within 2.0:1 VSWR SWR: Nominally 1.5:1 at 156.8 MHz Gain: 9 dB Max Input (Watts): 150 watts DC Ground: NO Height (feet): 23' Polarization: Vertical

SeaWatch® 19" Marine TV Antenna - 12VDC - 110VAC The Shakespeare SeaWatch® series of TV antennas are omni-directional over-the-air digital HDTV solutions that bring sleek lines and 360 degrees high-performance coverage to your watercraft. Designed to accept common 1in-14 threaded mounts, the antennas are well suited to fit virtually any application. Everything needed to connect the antenna to your converter or television is in the box. When paired with an optional 2-way band separator between the antenna and the amplifier, these antennas can also receive AM/FM radio signals. A full line of mounts and extension masts are available to fine-tune the installation. The 3019 antenna is designed for the mobile lifestyle and can be used on marine vessels, RVs, pop-up campers and more! Watch your favorite sports, sitcoms, reality TV, crime dramas, local news, weather, kids programming and more for FREE and in 1080 HD! Features: Low noise amplifier Omni-directional Recieves ALL local HD broadcast signals AC, DC and USB power adapter Best suited for areas up to 75 Miles from Broadcast Towers Specifications: Frequency Range: VHF:47-230MHz;UHF: 470-862MHz Receiving Range: FM/VHF/UHF Gain: 30dB Noise Figure: 3db Max. output lever: 110dBuV Impedance: 75ohms Connector: F-connectors Power Supply: DC 12V, AC 110v Dimensions: 19" x 3" Package Includes: 3019 Panel TV Antenna 20' RG-59 Coax Cable/F-Connectors USB/AC/DC Power Cords

Shakespeare Style 5241-R VHF Marine 36" LENGTH 3dB LOW PROFILE END-FED 1/2-WAVE WITH HEAVY-DUTY WHIP The perfect choice for bass boats, center console fishing boats, or any vessel where compact size is most important. Comes with a heavy-duty stainless steel whip for extra stability at high speeds. Chrome plated brass canister minimizes de-tuning. Sealed, tin-plated copper wire coil Requires mount with center hole for passage of the supplied 15' RG-58 cable. PL-259 connector included Stainless steel whip (36") Suggested mount: Shakespeare Styles 4187, 4188-S, or 4190 Ratchet Mounts Shakespeare Limited Warranty: 2 years Technical Specifications: Frequency: VHF Marine Band Bandwidth: 7 MHz SWR: 1.5:1 at 156.8 MHz Radiation pattern: Omni-directional Gain: 3 dB Max Input (Watts): 50 watts DC Ground: YES Height (feet): 3 Polarization: Vertical

Style 396-1 VHF 3dB Center-fed 1/2-wave coaxial sleeve Outstanding, basic 3dB antenna designed to reduce signal fading in rough seas. This is probably the most widely used antenna on Coast Guard vessels. Brass and copper elements Chrome-plated brass ferrule with standard 1-14 thread Includes 15' RG-58 cable and a PL-259 connector Suggested mount: Style 4187 Ratchet Mount One section Technical Specifications: Frequency: VHF Marine band Bandwidth: (within 2.0:1 SWR): 5 MHz SWR: 1.5:1 at 156.8 MHz Impedance (Ohms): 50 Gain: 3 dB Max Input (Watts): 50 DC Ground: NO Termination: 15' RG-58 cable Height (feet): 5 Polarization: Vertical Radiation pattern: Omni-directional

B953 Class B AIS Transceiver - 5W SOTDMA with VHF Antenna Splitter **As the FCC requires all units sold in the US to be programmed by a qualified technician. Please submit the form below for programming at the time of purchase. A copy of the MMSI registration or FCC Ship Station License is required along with the vessel master or owner's signature on the completed programming form.** Click here to download form. The B953 is a high transmit power (5W SOTDMA) AIS Class B transceiver that is small, and lightweight, yet delivers the very best AIS receive and transmit performance so you see more AIS information and targets at maximum range – all achieved with the least power consumption. The B953 has an integrated VHF antenna splitter which enables the transceiver to share your existing VHF antenna without any loss of performance. With built-in intelligent connectivity, integrated next-generation GPS receiver & antenna, and a unique FLEXI-FIT bracket system, safe and secure installation is simple. Features: Certified AIS Class B – 5W SOTDMA Integrated VHF antenna splitter Global certification - USCG / FCC / Canada / Europe SRT-AIS™ Transceiver Engine for superlative proven performance FLEXI-FIT™ bracket system for easy, convenient, and secure installation Internal high-performance GPS receiver and antenna (external antenna optional) Water, pressure spray, and damp proof (IPx6, IPx7 certified) Protected from vibration, shock, and extreme temperatures Small and lightweight Ultra-low power consumption – best in class Guaranteed connectivity and interoperability with any chart plotter or PC NMEA 0183 & NMEA 2000 Automated health and performance monitoring Silent mode (transmit-off) function Enhanced RF screening to protect against electromagnetic interference Built-in power surge protection Fail-safe VHF radio operation Physical & Environmental Specifications: Size (H x W x D): 150 x 115 x 45mm Weight: 415kg Operating temperature: -25°C to +55°C Storage temperature: -25°C to +70°C Ingress protection: IPx6 and IPx7 Electrical Specifications: Supply voltage: 12V or 24V DC Supply voltage range: 9.6V - 31.2V DC Average current (at 12V): 245mA Peak current: 2.5A Average power consumption (at 12V): 2.9W Galvanic isolation: NMEA 0183 inputs only, NMEA 2000, VHF antenna port Connectors: VHF antenna: SO-239 GNSS: TNC Power: 12-way circular multipole NMEA 2000: 5-way Micro-C connector USB: USB Micro-B Data Interfaces: NMEA 0183: 2 x bi-directional ports NMEA 2000: NMEA 2000 Ed 3.101, LEN=1 USB: PC virtual com port for NMEA 0183 data Standards Compliance: AIS standards: IEC 62287-2 Ed. 2, ITU-R M.1371.5 Product safety standards: EN60950-1 2006 +A11:2009 +A1:2010 +A12:2011 +A2:2013 EN62311:2008 Environmental standards: IEC 60945 Ed. 4 Serial data interface standards: IEC 61162-1 Ed 5.0, IEC 61162-2 Ed 1.0 NMEA 2000: NMEA 2000 Ed 3.101 GNSS performance standards: IEC 61108-1 Ed 2.0, IEC 61108-02 Ed 1.0 GNSS: Systems supported: GPS, GLONASS, BeiDou, Galileo (two of any combination, three including GPS, Galileo) Channels: 72 Internal/external antenna: Internal or optional external antenna Time to first fix from the cold start: 26s VHF Transceiver: VDL access scheme: SOTDMA Operating frequency: 156.025MHz - 162.025MHz Channel bandwidth: 25kHz Receivers/transmitters: 2 x receivers, 1 x transmitter AIS receiver sensitivity (20% PER): -111dBm AIS transmitter power: 5W (+37dBm) User Interface: Indicators: Power, transmit timeout, error, silent mode In the Box: 1 x AIS transceiver 1 x Power and data cable (2M) 1 x VHF radio accessory cable 1 x FLEXI-FIT™ mounting bracket Complete with screws & optional fixing tape

Style 4018 VHF 9dB Phased 1/2-wave elements in a collinear array with a coaxial choking sleeve to suppress cable radiation The top choice for charter boat captains and experienced sport fishing enthusiasts. This long-distance VHF antenna is rigid enough to stay erect in rough seas, yet exceptionally lightweight. Brass and copper elements Chrome-plated brass ferrules Includes 20' RG-58 cable and a PL-259 connector Suggested mount: Style 409-R or 410-R Mounting Kit for deck or side mounting Two sections: base 162", tip 66" Technical Specifications: Frequency: VHF Marine band Bandwidth: (within 2.0:1 SWR) 3 MHz SWR: 1.5:1 at 156.8 MHz Impedance: (ohms): 50 Gain: 9 dB Max Input (Watts): 25 DC Ground: NO Termination: 20' RG-58 Height (feet): 19 Polarization: Vertical Radiation pattern: Omni-directional

Shakespeare CENTENNIAL™ Style 5120 - Reduced Length Version 8' LENGTH, AM/FM Marine 8' LENGTH, AM/FM ANTENNA INCLUDES CABLE AND CONNECTOR Continuing the tradition, Shakespeare's Centennial™ 5120 AM/FM antenna puts high-end features where high-end does the most good. When you're far from your favorite stations, this antenna helps bring them in loud and clear, without depleting your net worth. Chrome-plated brass ferrule with standard 1"-14 thread Includes 15' RG-62 cable and Motorola connector Suggested mount: Shakespeare Style 4187 Ratchet Mount One section Shakespeare Limited Warranty: 2 years Technical Specifications: Frequency: 550-1600 KHz, 88-108 MHz Impedance: (Ohms): 93 Termination: 15' RG-62 cable, Motorola Plug Polarization: Vertical