Installs and removes shift cables on MC-I, R-MR, Alpha One, Alpha One/Gen II drive units. Use with 18-2190 and 18-2190E cables. Replaces: Mercury Marine 91-12037.

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Original Equipment Quality Replacement Tilt Trim Motor for Mercury/Mariner Outboards with Design II 3 RAM Replacement outboard tilt trim motor that will fit Mercury/Mariner outboards w/Design II 3 ram, three-wire trim units, Hollow-hex shaft W/AFT FILL RESERVOIR, 3-wire connection, 2-bolt mount, Shaft adaptor, and O-ring included, Ring Terminal Ends.  ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor. Features: Tilt trim motors are dynamically tested to ensure out-of-the-box performance  Motor shafts induction case hardened at bearing surfaces for superior wear resistance  Epoxy Powder coated for maximum insulation protection Warranty Information: When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.  Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration  Replaces: MERCURY Tilt Trim Motor 811628 MERCURY Tilt Trim Motor 828708A1 MERCURY Tilt Trim Motor 878265A6 SIERRA Tilt Trim Motor 18-6774 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Mercury/Mariner Outboard Relay with Shroud & Grommet Mercury/Mariner outboard relay that will fit Mercury & Mariner Outboards. 12 Volt, 30 Amp Replaces: Mercury Marine 828151 Mercury Marine 828151A1 Mercury Marine 882751A1 *ARCO Assurance 12-month part and labor warranty protection This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Replacement Outboard Tilt Trim Motor & Reservoir Only - Mercury/Mariner & Force Motor Replacement outboard tilt trim motor and reservoir that will fit late model Mercury /Mariner, Force 40-125 HP outboards w/single ram, 2-wire connection, 4-bolt mount, Hollow-hex shaft, (Motor/Reservoir Only) Includes stainless steel mounting screws, shaft adaptor, O-ring and fill plug. Bullet Connector Terminal Ends. ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor. Features: Tilt trim motors are dynamically tested to ensure out-of-the-box performance  Motor shafts induction case hardened at bearing surfaces for superior wear resistance  Epoxy Powder coated for maximum insulation protection Warranty Information: When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.  Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration  Replaces: MERCURY Tilt Trim Motor 19217A1 MERCURY Tilt Trim Motor 19217A5 MERCURY Tilt Trim Motor 809885A1 MERCURY Tilt Trim Motor 809885A2 MERCURY Tilt Trim Motor 809885T2 MERCURY Tilt Trim Motor 811674 MERCURY Tilt Trim Motor 813447 MERCURY Tilt Trim Motor 818903A1 MERCURY Tilt Trim Motor 819479A1 MERCURY Tilt Trim Motor 8197480A1 MERCURY Tilt Trim Motor 819762A4 MERCURY Tilt Trim Motor 19762A5 MERCURY Tilt Trim Motor 19762A6 MERCURY Tilt Trim Motor 19762A7 MERCURY Tilt Trim Motor 1977A8 MERCURY Tilt Trim Motor 1977A9 MERCURY Tilt Trim Motor 22870A1 MERCURY Tilt Trim Motor 30250A3 MERCURY Tilt Trim Motor 30250T3 MERCURY Tilt Trim Motor 2021A1 MERCURY Tilt Trim Motor 32021T1 MERCURY Tilt Trim Motor 32021A2 MERCURY Tilt Trim Motor 32021T2 MERCURY Tilt Trim Motor 55654A1 MERCURY Tilt Trim Motor 55654T2 MERCURY Tilt Trim Motor 893907A02 SIERRA Tilt Trim Motor 18-6777 This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Chesapeake Black 2" Trim Gauge (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha '01 and newer) Perimeter-lighted Black dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens. 2"- Hole Size: 2.0625" (53mm) For Engine Types: (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha '01 and newer) Specifications: Anti-scratch glass lens Perimeter lighted back light 12 VDC negative ground Can be adapted for 24 VDC systems Factory P/N GP9402 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Chesapeake White SS 2" Trim Gauge (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha - '01 and Newer) Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel, contoured White pointer and domed glass lens. 2"- Hole Size: 2.0625" (53mm) For Engine Types: (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha-2001 and newer) Specifications: Anti-scratch glass lens Plastic Cases for corrosion resistance and long life 12 VDC negative ground Can be adapted for 24 VDC systems Factory P/N GP9649 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Dress White 2" Trim Gauge (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha '01 and newer)  Perimeter-lighted White dial with bold Black graphics, White aluminum bezel, contoured Black pointer and flat glass lens. 2"- Hole Size: 2.0625" (53mm) For Engine Types: (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha '01 and newer) Specifications: Anti-scratch glass lens 12 VDC negative ground Can be adapted for 24 VDC systems Factory P/N GP9712 *Sold as an Individual *Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Euro Black 2" Trim Gauge f/ Mercury/Mariner/Mercruiser/Volvo DP/Yamaha '01 and Newer Perimeter-lighted Black dial with bold White graphics, Black aluminum bezel, contoured White pointer and flat glass lens.  2"- Hole Size: 2.0625" (53mm) For Engine Types: Mercury / Mariner / Mercruiser / Volvo DP / Yamaha '01 and Newer Specifications: Anti-scratch glass lens 12 VDC negative ground Perimeter-lighted Black dial Can be adapted for 24 VDC systems Factory P/N GP9374 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Euro White 2" Trim Gauge f/ Mercury / Mariner /Mercruiser/Volvo DP/ Yamaha '01 and newer Perimeter-lighted White dial with bold Black graphics, Black aluminum bezel, contoured White pointer and flat glass lens. 2"- Hole Size: 2.0625" (53mm) For Engine Types: Mercury/Mariner/Mercruiser/Volvo DP/Yamaha '01 and newer Specifications: Anti-scratch glass lens Perimeter-lighted White dial 12 VDC negative ground Can be adapted for 24 VDC systems Factory P/N GP9709 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Kronos 2" Trim Gauge (Mercury/Mariner/Mercruiser/Volvo DP/Yamaha-2001 and newer) Polished Stainless Steel bezel, flat glass lens, perimeter lighted spun aluminum dial with Gold and Black graphics. Gold increments and Logo on dial are Embossed.  All instruments include two piece Newport pointer with White hub. 2" - Hole Size: 2.0625" (53mm) For Engine Types: (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha-2001 and newer) Specifications: Flat Scratch Resistant Lens Polished Stainless Steel bezel LED Illuminating around the Perimeter of the Dial Newport style White Pointer Factory P/N GP7681 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Spun Silver 2" Trim Gauge for Mercury/Mariner/Mercruiser/Volvo DP & Yamaha ('01 & Newer) Perimeter-lighted Silver dial with bold Black graphics, polished stainless steel bezel, contoured Black pointer, and domed glass lens. 2"- Hole Size: 2.0625" (53mm)  For Engine Types: (Mercury / Mariner / Mercruiser / Volvo DP / Yamaha - '01 and newer) Specifications: Domed, Scratch Resistant Lens Stainless Steel Bezel LED Illuminating around the Perimeter of the Dial Factory P/N GP9223 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Temperature Sender 250°F/120°C Floating Ground - 3/8-18 NPTF  Features: Ground - Floating Connection - .25" Spade Voltage - 6-24V Thread - 3/8-18 NPTF Component Reference No. - 805/1/5 Max. Temperature Scale - 250°F/120°C  *Sold as an Individual WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Mercury/Mariner Outboard Starter - 10 Tooth The outboard starter will fit Mercury /Mariner, 50-90 HP/65 HP Jet, and 10-tooth drive gear.  ARCO advises using a fully charged battery - A weak battery can damage the starter and starter solenoid.  And to also clean all connections - A corroded connection creates resistance, lowering the amperage required for an efficient starting circuit. Features: Dynamically tested and packaged for out-of-the-box performance Nickel-coated and epoxy-painted to reduce corrosion  Sealed to minimize water intrusion Designed for long life and optimum performance Armatures are tested to withstand 50 times operating voltages (12 volts) Warranty Information: When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.  Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration Replaces: Mercury 50-44369A1 Mercury 50-60315 Mercury 50-65436 Mercury 50-66015 Mercury 50-66015-2 Mercury 50-66015-T Mercury 50-893891T This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Zinc Wedge Anode for 35-300 HP Mercury/Mariner Engines Tecnoseal Zinc Wedge Anode for Mercury/Mariner 35-300 HP engines. Wedge anode located on the side of the gear housing just above the cavitation plate. For use in salt water. Mercury part number 826134.