|
March TE-5.5C-MD Mag-Drive Centrifugal Pump single phase with 115/230V Motor
Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.
March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
The TE-5.5C-MD pumps Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Nitric Acid, Phosphoric Acid, Potassium Chloride, Potassium Hydroxide, Sodium Hydroxide (Caustic Soda), Sodium Chloride, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.
Unit System 60Hz 50Hz Max Flow
30 GPM
102 LPM
Max Head
41 FT
9 M
Power
.33 HP
.248 KW
Electrical
1PH 115/230V 3PH 230/460V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1"FPT
Outlet
3/4"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)
|
864.90 |
|
|
Applications for the TE-5.5C-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.
March Pump's industrial TE-5.5C-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 30 gallons per minute at 11 feet, and its maximum head is 41 Feet (or around 18PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Viton, Ryton/Teflon/Carbon, and Ceramic. The inlet connection is 1 inch female pipe thread, and the outlet is 0.75 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.33 Horsepower air cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March TE-5.5C-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
The TE-5.5C-MD pumps Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Hydrochloric Acid (Muriatic), Nitric Acid, Phosphoric Acid, Potassium Chloride, Potassium Hydroxide, Sodium Hydroxide (Caustic Soda), Sodium Chloride, Sulfuric Acid, Fresh Water, Salt Water, DI Water, and many more chemicals.
Unit System 60Hz 50Hz Max Flow
30 GPM
102 LPM
Max Head
41 FT
9 M
Power
.33 HP
.248 KW
Electrical
1PH 115/230V 3PH 230/460V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1"FPT
Outlet
3/4"MPT
Wet End
Polypropylene (Front and Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers)
|
872.10 |
|
|
Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim
|
3440.34 |
|
|
Sierra o-rings for Mercury and Mercruiser.
|
8.99 |
|
|
Alcohol resistant, Priced per foot, Sold in 50' rolls only.
|
2.39 |
|
|
A special blend of synthetic base oil and balanced additive system that exceeds the FC-W requirements for marine engine oil. Recommended for gasoline and diesel inboard and sterndrive engines. Provides superior engine protection during startups, operation and storage. Reduces friction and wear for extended engine life with longer lubrication effectiveness than mineral oils. Reduces oil consumption and improves fuel economy. Sold in case quantities only, priced each.
|
73.09 |
|
|
Sierra oil seals for lower unit applications in Johnson, Evinrude, BRP and OMC Sterndrive/Cobra engines.
|
15.99 |
|
|
Sierra oil seals for lower unit applications in Johnson, Evinrude, BRP and OMC Sterndrive/Cobra engines.
|
9.99 |
|
|
All black, corrosion resistant 6mm thick tubing. Sold only in 100' roll, priced per foot.
|
1.09 |
|
|
Premium quality motor oil formulated to meet or exceed warranty requirements for 4-stroke stern drive and inboard engines. This oil offers excellent detergency, anti-oxidants, antiwear and corrosion protection. Meets or exceeds quality performance API SJ, CF-4, CH-4. Recommended for use in Mercruiser, OMC and Volvo Penta. Sold in case quantities only, priced each.
|
73.19 |
|
|
Blended with premium grade synthetic and mineral based stock combined with superior designed additives formulated for the extreme rigors of the marine environment. Features superior corrosion protection, advanced lubrication for reduction of wear to internal engine components and minimized piston ring deposits. Extensively tested for outstanding performance. Sold in case quantities only. Priced each.
|
83.69 |
|
|
Sierra oil seals for lower unit applications in Johnson, Evinrude, BRP and OMC Sterndrive/Cobra engines.
|
11.99 |
|
|
Sierra oil seals for lower unit applications in Johnson, Evinrude, BRP and OMC Sterndrive/Cobra engines.
|
8.99 |
|
|
Sierra replacement distributor caps for inboard and inboard/outdrive engines.
|
4.99 |
|
|
Sierra pivot pin end caps for Mercruiser.
|
12.99 |
|