Sierra Marine Engine Parts & Drive Parts   Sierra Marine is a trusted name in aftermarket replacement boat engine and drive parts. Sierra’s products are designed and engineered to exceed the high horsepower demands of today’s engines in the harshest marine environments. All Sierra products meet or exceed the original equipment part it replaces.   If you need help finding a part, we need, Make, Model, Year, Horsepower, and Serial number of your engine.   Warning: We can no longer ship engine parts International or to California Due to Prop 65.

Sierra fuel water separators remove over 98.8% of emulsified water from gasoline. Sierra's 10 micron filters are over 90% efficient at removing particles as small as 10 micron. All filters flow at 90 GPH. 10 micron filters are recommended to prevent damage to inboard and outboard fuel injection systems. Kits include two brass pipe plugs. Display packaged.

Sierra's 10 micron filters are over 90% efficient at removing particles as small as 10 micron. All filters flow at 90 GPH. 10 micron filters are recommended to prevent damage to sensitive inboard and outboard fuel injection systems. Display packaged.

Fuel/Water Separator Keep your engine running at peak efficiency by filtering out any water that may get into the fuel system. 10-micron filtering capability. Features: Double seal for enhanced performance Replacement for: Mercury 35-60494-1, Aqua Power 6031, GLM 24940, Sierra 18-78250, SMI 15494, Valmar 52113, Marpac 7-0872

Universal Fuel/Water Separator Kit with Bracket Keep your engine running at peak efficiency by filtering out any water that may get into the fuel system. 10-micron filtering capability and fits all 2 and 4-cycle engines. Features: 10 Micron Filter and bracket included Outfitted with 2 brass plugs for secure connections and universal 3/8 inch (.85cm) ports Double seal for enhanced performance Replaces Mercury 35-60494A4

Replacement filter element for Turbine Series fuel water separators. Integrated bail on top of end cap for easy removal.

Replacement filter element for Turbine Series fuel water separators. Integrated bail on top of end cap for easy removal.

Replacement filter element for Turbine Series fuel water separators. Integrated bail on top of end cap for easy removal.

Yamaha Fuel Line Kit 6' x 3/8" Attwood's low-permeation fuel line kits set the standard in performance, safety, and value. Along with featuring Attwood's award-winning Universal Sprayless Connector, these kits meet strict United States EPA regulations. Attwood Corporation has been an award-winning leader in engineering, testing, and manufacturing the highest quality marine products for over 100 years. We deliver safe and reliable lighting, fuel systems, water systems, seating & pedestals, swim ladders, custom upholstery, and general marine accessories that are easy to install and meet regulatory compliance. Features: Includes Attwood's award-winning Universal Sprayless Connector; no more dangerous fuel sprays when connecting and disconnecting pressurized lines Multi-layer low-permeation primer bulb with 60% more fuel output compared to competitors Includes 3/8-inch low-permeation fuel hose that resists kinking and hardening; rated up to 100 degrees Centigrade Versatile: compatible with Ethanol blended fuels, Yamaha Brand engines and tanks Attwood products are both compatible and reliable, engineered and built with a never-fail attitude WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Fuel Flow Sensor with 10' cable & T-connector Fuel Flow Sensor Gasoline ONLY. 1 required per engine. Up to 3 engines supported. Outputs: Fuel Flow Tank Fuel Used Trip Fuel Used Seasonal Fuel Used Cable Length: 10' Fuel Line Diameter: 3/8" (9.5mm) Inside Diameter Flow Rate Measured: Optimized for 0.6-45 Gal/hr but can measure outside these values Added Back Pressure to the fuel system: 0.5 PSI at 20 Gal/hr; 1 PSI at 40 Gal/hr Installation Location: Above the max level of the fuel tank, in-line after the fuel filter and any Y's or T's in the line Package: The Fuel Flow Sensor, N2K T and 2 (two) 1" hose clamps Fuel Type: Gasoline only. The Fuel Flow Sensor does not operate diesel engine fuel systems Hole required to route through a bulkhead: 22mm (7/8") Multiple Fule Flow sensors possible: Yes

PleasureCraft Marine RP061022 Impeller for Raw Water Pump Impeller for 2003 and newer PCM engines using Serpentine belt and PCM water pump Not for v-belt systems!   Fits Crusader and Pleasurecraft Marine PCM 5.0 , 5.7, 6.0 & 8.1 models with serpentine belt driven water pumps. Will not for V-belt systems.   Replaces : Crusader and Pleasurecraft R061022 , RP061022 , Sierra 18-8926 , Mallory 9-45718

Each kit contains 2 fuel/water separating filters and a mounting bracket. 2 brass pipe plugs are also included. Display packaged.

Spun Silver Box Set of 6 Gauges f/ Inboard Engines - Speed, Tach, Voltmeter, Fuel Level, Water Temperature & Oil Packaged and ready for the display counter. This 6 gauge boxed set offers a complete set of gauges ready to install.  Boxed Set Includes: Tachometer (0 to 6000 RPM) Speedometer (0 to 55 MPH) Fuel Level (E to F) Voltmeter (10 to 16 AMPS) Water Temperature (100 to 250° F) Oil Pressure (0 to 30 PSI) Factory P/N KTF0184 *Sold as a Box Set **Gauge Covers not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Euro Black 4" Multifunction Gauge - Volt/Fuel/Oil/Water Temperature Perimeter-lighted Black dial with bold White graphics, Black aluminum bezel, contoured White pointer and flat glass lens.  Multi-Function Gauge Displays: Fuel (E to F) Volts (10 to 18 AMPS) Oil Pressure (0 to 80 PSI) Water Temp. (120 to 220° F) 4" Gauge - Hole size: 3.4" (86.36 mm) Features: Anti-scratch glass lens Plastic Cases for corrosion resistance and long life Perimeter-lighted Black dial Can be adapted for 24 VDC systems Factory P/N GF0001 *Sold as an Individual **Gauge Cover not Included This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Danfoss 180X5225 Filter Cart 10" 10 Micron Filter element 180X5225 1.06 in 27.00 mm 10.00 in 254 mm 2.75 in 70 mm SOE Flow [gpm] [Max]: 7.900 Flow [m³/h] [Max]: 1.80