|
0183 to N2K Gateway with PC Interface, USB
The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.
The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.
The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data.
Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.
The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.
Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application.
Features:
Vital NMEA 2000 diagnostic tool.
USB version is fully isolated to prevent dangerous ground loops.
Up to 230,400 baud rate data transfer rate.
Integrated 1.8m USB cable.
Diagnostic LEDs on both input and output.
Integrate Seamlessly with Raymarine® Products
The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.
|
266.89 |
|
|
0183 to N2K Gateway with PC Interface, ISO
The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.
The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.
The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data.
Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.
The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.
Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application.
Features:
ISO version has OPTO-isolated input and ISO-Drive output for safely interfacing with NMEA 0183 or RS232 / RS422.
Advanced configuration using the Actisense Toolkit allows Tx / Rx lists and Tx rates to be set.
Supports fast-heading at 10Hz.
Up to 230,400 baud rate data transfer rate.
Integrated 0.75m ISO cable.
Diagnostic LEDs on both input and output.
Integrate Seamlessly with Raymarine® Products
The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.
|
249.86 |
|
|
LANLink NMEA 0183 To Ethernet Gateway
More and more boats now have a wireless router fitted or utilize services like Digital Yacht 4G Connect for internet connectivity. LANLink is an NMEA to ethernet gateway that enables the boat’s NMEA data to integrate into the router network -allowing connected devices and apps to take advantage of the data.
LANLinkis available in two versions suitable for NMEA 0183 and NMEA 2000 respectively. It features an easy-to-use web interface allowing any device with a browser to configure NMEA baud rates and IP/Port information.
It can support multiple TCP/IP connections and is bi-directional. Once connected to the onboard network via a simple CAT 5/6 patch cable, users can set apps like TZ iBoat, iNavX, NavLink, iSailor, Imray, Weather 4D, etc., by simply entering the IP address and port for streaming NMEA data.
Features:
NMEA 0183 to ethernet gateway version
12/24v DC low power operation
Connects to router or devices via simple RJ45 Cat 5/6 patch cable connection
The web user interface for easy setup from the connected device via the browser
TCP/IP or UDP connection modes –support for up to 5 connected devices with TCP/IP
Bi-Directional
The NMEA 2000 variant can offer raw mode with encapsulated PGNs or conversion mode (for apps) supporting AIS, instruments, and GPS
RS232 port for PC apps too
Status indicators for power, data in-out, network link, and server status
Set-Up:
Easy menu-driven web UI accessible via web browser on a client device with no complicated software to install for setup
Configure NMEA data for 4800 or 38400 baud and set mode (TCP/IP or UDP) and port
Set up with fixed or dynamic IP address
Status page for system diagnostics
Specifications:
Power: 10-35V DC (Consumption approx. 50mA at 12V DC)
Network Port: Ethernet RJ45 10/100MB
IP Mode: Static or DHCP
Operating Mode *TCP/IP or UDP; Support for up to 5 connected devices in TCP/IP mode; *Recommended mode of operation
NMEA Input: Configurable 4800 or 38400 baud (NMEA 0183)
NMEA 2000 option via iKonvertgateway
Operating temp: -25 to +70 degrees C
LED Indicators: Power -Status -Link -Data In -Data Out
Options: RS232 connectivity (non-concurrent with NMEA)
Dimensions (W x H): 95mm x 86mm
|
193.15 |
|
|
Marine Navigation & Instruments, Supplies and Equipment
With a wide variety of Marine Navigation equipment and Instruments, we can help you find your location on the waterways, avoid hazards, and be respectful of other boaters. The accessories you have on your boat are important, but very few of them are as valuable as the AIS systems, autopilots, black box modules, and other options you can choose from when you want to make sure you can find your way there and back again while staying away from areas that could mean running aground or experiencing other dangers. We offer many types of navigation equipment, including cameras - network video, ice flashers, and marine monitors.
Depending on where you are going to be boating and what you plan to do with your time on the water, you can also find a fishfinder/sounder - color or a fishfinder/sounder - mono that will be right for you, along with GPS - chartplotters, GPS - fishfinder combos, or a GPS - track plotter. Network accessories and network capable displays are available, and we have a selection of night vision, software, transducers and transducer accessories, and weather fax equipment. If you need radar - stand alone options or radar domes / arrays, look no further than right here, where the selection is good and so are the prices.
|
|
|
iKonvert NMEA 2000 Gateway with ISO Interface
The iKonvert NMEA2000-0183 Gateway/Converter is an intelligent and flexible gateway for allowing new NMEA2000 equipment to talk to legacy NMEA0183 equipment. Conversions are bi-directional, so whether you want to get the data from older NMEA0183 sensors on to your NMEA2000 network or you have added a new NMEA2000 only MFD and want it to send GPS and Navigation data to your older NMEA0183 VHF and Autopilot, iKonvert will accurately and intelligently carry out the required data conversions.
There are many, many real life applications for NMEA2000 to NMEA0183, with a plethora of different makes and models of equipment that may need to be connected together. We have designed iKonvert to satisfy as many of these situations as possible by incorporating a simple but effective mode selection method, via a set of DIP switches inside iKonvert. Just remove two screws, open the iKonvert box and using a small screw driver, select the mode you need. The next time iKonvert powers up, it will automatically carry out the conversions you selected.
A number of modes have already been defined including; Heading, Sounder, AIS, GPS, Wind, Instruments and an all data gateway mode, which automatically sets the conversions to be done and the baud rate iKonvert will use. What is more, if you need a mode that we have not defined yet, just let us know and we will consider including it.
Digital Yacht’s iKonvert Gateway is housed in a compact and easy to mount housing, with an integral NMEA0183 cable and standard NMEA2000 Micro drop cable (male). Taking its power from the NMEA2000 network, and providing full galvanic isolation between the NMEA0183 and NMEA2000 networks, iKonvert is the perfect solution for all NMEA conversions.
For customers that want to take this converted data in to a computer, please consider the iKonvert USB gateway, that features an integral USB cable that is compatible with all of the popular operating systems (Windows/Mac/LINUX/Android).
Features:
Small but powerful bi-directional NMEA2000 to NMEA0183 Converter
Powered from the NMEA2000 network
Opto Isolated NMEA0183 Interface
Converts AIS, GPS, Navigation, Instrument and XDR data
Features “Real Life” data modes for most common installations
Simple configuration of data modes using DIP switches
Integral NMEA0183 cable and NMEA2000 Micro (Male) cables
Full galvanic isolation
|
176.35 |
|
|
USG-2 Isolated USB To Serial Gateway For Use w/NMEA0183,RS422 And RS232
The USG-2 converts a USB port into a bi-directional serial port suitable for
connecting to a marine standard NMEA 0183 data bus.
It provides a far safer connection when compared to standard USB to serial converters.Electrical isolation is provided by the ISO-DriveTM output and OPTO-isolated input making installation simple and free from groundloops.
The input uses the Actisense OPTO-isolation circuitry to protect any connected equipment from the most common system faults.The input can receive very low level signals that are often too small to be received by a PC erial port.
The high quality,shielded USB lead included with the USG-2 makes connection to a PC simple while providing a high level of water protection when connected to the custom designed USB socket.The pluggable screwless connector makes installation quick and easy, and the specifically designed DIN rail mount option ensures a reliable secure bulkhead mount for the USG-2.Multiple LEDs make diagnosing connection issues quick and easy.The blue power LED Illuminates solid blue when the USB driver has successfully loaded and the USG-2 is powered, while a green (receive) LED and an orange (transmit) LED indicate whether data is present.
Features:
NMEA 0183, RS422
RS232 compatible
ISO-Drive™ technology
Isolated input (2500V)
Isolated output (1500V)
Encapsulated electronics
High retention USB socket
Diagnostic LEDs
Baud rates from 300 to 230400 bps
Bulkhead mount,with optional DIN rail mount kit
Pluggable screwless connector with locking latch & strain
|
161.05 |
|
|
LANLink NMEA 2000 To Ethernet Gateway
More and more boats now have a wireless router fitted or utilize services like Digital Yacht 4G Connect for internet connectivity. LANLink is an NMEA to ethernet gateway that enables the boat’s NMEA data to integrate into the router network -allowing connected devices and apps to take advantage of the data.
LANLinkis available in two versions suitable for NMEA 0183 and NMEA 2000 respectively. It features an easy-to-use web interface allowing any device with a browser to configure NMEA baud rates and IP/Port information.
It can support multiple TCP/IP connections and is bi-directional. Once connected to the onboard network via a simple CAT 5/6 patch cable, users can set apps like TZ iBoat, iNavX, NavLink, iSailor, Imray, Weather 4D, etc., by simply entering the IP address and port for streaming NMEA data.
*This version ships with an iKonvertNMEA Certified gateway
Features:
NMEA 2000 to ethernet gateway version
The NMEA 2000 version ships with an iKonvertNMEA Certified gateway for easy connection to the NMEA 2000 backbone (easily configurable for multiple installation options)
12/24v DC low power operation
Connects to router or devices via simple RJ45 Cat 5/6 patch cable connection
Web user interface for easy setup from the connected device via browser
TCP/IP or UDP connection modes –support for up to 5 connected devices with TCP/IP
Bi-Directional
The NMEA 2000 variant can offer raw mode with encapsulated PGNs or conversion mode (for apps) supporting AIS, instruments, and GPS
RS232 port for PC apps too
Status indicators for power, data in-out, network link, and server status
Set-Up:
Easy menu-driven web UI accessible via web browser on a client device with no complicated software to install for setup
Configure NMEA data for 4800 or 38400 baud and set mode (TCP/IP or UDP) and port
Set up with fixed or dynamic IP address
Status page for system diagnostics
Specifications:
Power: 10-35V DC (Consumption approx. 50mA at 12V DC)
Network Port: Ethernet RJ45 10/100MB
IP Mode: Static or DHCP
Operating Mode *TCP/IP or UDP; Support for up to 5 connected devices in TCP/IP mode; *Recommended mode of operation
NMEA Input: Configurable 4800 or 38400 baud (NMEA 0183)
NMEA 2000 option via iKonvertgateway
Operating temp: -25 to +70 degrees C
LED Indicators: Power -Status -Link -Data In -Data Out
Options: RS232 connectivity (non-concurrent with NMEA)
Dimensions (W x H): 95mm x 86mm
|
293.95 |
|
|
Keywords: raymarine, i70 multifunction color instrument, i50 instrument, raymarine depth gage, raymarine speed gage, raymarine tridata instrument display, raymarine instrument displays, raymarine multifunction display
|
|
|
NavLink 2
“NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed to make NMEA 2000 navigation data available for apps on smartphones, tablets, iPads and PCs.”
Features:
NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed so that NMEA 2000 navigation data can be made available for apps on smartphones, tablets, iPads and PCs. Installation takes seconds as a result of direction connection to the NMEA 2000 back bone and self-powered from the data network.
Once installed, it creates a local WiFi network for devices to connect or can be programmed to join an existing wireless network if one is already installed. This is ideal for devices like the Furuno wireless radar which require operation through their own dedicated network but require NMEA 2000 data integration for charting apps.
NavLink 2 now works with the popular Navionics Boating App for Apple iOS and Android. Therefore allowing display of GPS and AIS data on your Navionics charts.
Specifications:
NMEA 2000 to WiFi server
Self powered from NMEA 2000 bus – fits in seconds
Supports TCP/IP and UDP connection modes
Provides AIS, navigation and instrument data to apps
Compatible with all popular apps like iNavX, TimeZero, Weather 4D, Navionics, SailGrib, NavLink, iSailor, SeaPilot, AquaMap etc
Up to 7 connected devices
Compatible with Windows, Linux, MAC OS, iOS and Android
Easy web interface for programming
Password protected
Can act as dedicated wireless server or rather can connect to an existing wireless network
Diagnostic data display mode and LED status lights
Internal hi gain WiFi antenna
Super-fast 230KBs operation
Optional raw data mode for developers and likewise advanced users
Supplied with NMEA 2000 cable
|
235.15 |
|
|
i50 SeaTalkng Instruments - Tridata with Thru-Hull Transducer
The i50 Instruments from Raymarine offer boaters an excellent combination of great looks, high performance, and extreme value. Designed to accommodate either stand-alone or fully integrated installations, the i50 instruments feature Raymarine's exclusive SeaTalkng networking for simple installation and bullet-proof reliability. Each instrument offers extra-large digits, razor-sharp LCDs, and red backlighting for outstanding visibility in all lighting conditions. i50 Digital Instrument displays are fully compatible with our i70 Color Multifunction Instrument too. Boaters can now customize their systems with any combination of monochrome LCD, color LCD, and analog instruments as needed. Raymarine also offers the p70 and p70R Color Autopilot controllers which also match our instruments and multifunction displays.
For the ultimate in flexibility, the i50 Instruments support SeaTalkng CANBUS networking, as well as our original SeaTalk 1 networking. This makes upgrading older instruments a breeze. Connect your analog depth, speed, and wind transducers directly to the respective instrument display, or use the displays as repeaters for SeaTalkng smart transducer data: the choice is yours.
The ultra-sleek design of the i50 line is designed to complement our full line of a-Series, c-Series, and e-Series Multifunction displays, and looks great on the helm of any boat. Each instrument has a low-profile surface mounting kit and silicone rubber sun cover. An optional bracket mounting kit is also available separately.
i50 Instruments are designed to operate from 12V DC power and are ultra-efficient drawing less than 1W as repeaters, or 2.4W while hosting a transducer. All of the i50 Instruments are waterproof to IPX6 standards. The i50 instruments are all covered by Raymarine's industry-leading 2-year warranty, upgradeable to 3 years at no charge by registering online within 90 days of purchase.
i50 Tridata Instrument
The i50 Tridata is a convenient 3-line instrument that combines the Speed and Depth Instruments functions into one display. This makes the i50 Tridata ideal for installations on helms where space is a premium or as a depth and speed repeater solution for other locations on the boat.
Red backlighting for outstanding night-time visibility.
SeaTalkng and SeaTalk-1 connectivity for maximum flexibility
Use a primary display or as a repeater of i50 depth and speed instruments
Built-in depth and speed transducer connections
M78713-PZ Nylon Depth Transducer with 45ft cable
E70673 ST900/P120 S/T Thru Hull - 13.7m Cable
The i50 Tridata's 3-line LCD can show current depth, current speed, distance log, trip log, and water temperature. Additional display modes include maximum speed, average speed, and VMG to windward. Tridats have a count-up timer and 2 race start timers for racers. Tridata's robust alarm functions include a shallow depth alarm, deep depth alarm, shallow anchor alarm, and deep anchor alarm.
Features:
Ultra-modern design complements Raymarine's latest a-Series, c-Series, and e-Series Multifunction display and instrument systems.
Large, crisp LCDs with high contrast for excellent visibility.
Red backlighting for outstanding night-time visibility.
SeaTalkng and SeaTalk-1 Networking for maximum flexibility.
Fully compatible with i70, p70, and p70R Color Instruments and Autopilots.
110mm x 115mm footprint is identical to older Raymarine ST60+ instrumentation making upgrading easy
|
884.99 |
|
|
SimNet to N2K Adaptor Kit - Connect Simrad heading sensor (FC40, RC42) to
NMEA 2000 network; includes Simnet-to-N2k male adaptor, Simnet-2 Joiner,
T connector.
|
101.94 |
|
|
MR1308UAB Marine Stereo w/AM/FM/BT/USB
The Boss MR1308UAB marine digital media receiver is designed for marine use, with a UV-resistant exterior that resists fading and a conformal-coated PC board that resists corrosion. It blends into most boat interiors and offers an impressive list of features.
This digital media receiver gives you the freedom to enjoy all your favorite music. With built-in Bluetooth and integrated microphone, you get the safety and convenience of hands-free calling and audio streaming with compatible smartphones and devices. You can also listen to your favorite AM/FM stations, play music stored on a USB drive or SD card, or plug your MP3 player into the 3.5mm aux input. All the openings are protected from salt and spray when not in use, of course. Control all functions (except for Bluetooth) with the included remote.
The Boss MR1308UAB digital media receiver offers plenty of sound-shaping tools, with four preset modes and independent bass and treble control. If you want to connect an external amp, you can use the pair of 2-volt RCA outputs.
The fold-down faceplate features a single-line alphanumeric-text display that's easy to read day or night. When you leave your boat at the dock, you can slip the detachable face into the hard plastic carrying case included with your purchase.
Features:
Marine digital media receiver with built-in amplifier
AM/FM w/30 presets
USB/SD Card Slot
Water-proof, conformal coated circuit boards
Wireless Remote
Detachable face
Technical Specifications:
200 Watts peak power
Dimensions (H/W/D) - 2.125" x 7.125" x 5"
Chassis type - Single-DIN
Presets - 18 FM/12 AM
In the Box:
MR1308UAB Stereo head unit
Remote control
Carrying case
Mounting hardware
Owner's manual
∗SiriusXM Promotion - Get 3 Free Months SiriusXM Streaming Service - LINK
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
58.00 |
|
|
IS42J Instrument Links J1939 Diesel Engines to NMEA 2000® Network
More than a standalone gauge, the IS42J links J1939 diesel engines to the boater’s NMEA 2000® network. This allows boaters to view engine data on a wide range of other Simrad gauges and multifunction displays, vessel-wide, without the need for a separate J1939 gateway or converter.
The IS42J is simple to install, with only one cable required for each J1939 engine and a single connection to the boat’s DC power supply. With a dual-engine J1939 gateway built in, there are no separate black-box components to install, and plug-and-play adapter cables are available to suit a wide range of J1939 diesel engines. Sharing engine data with other Simrad gauges or displays is also simple via NMEA 2000® connectivity.
Key Features:
Bright, optically bonded 4.1-inch color display
Monitor up to two J1939 connected engines
Built-in J1939-to-NMEA 2000® gateway
Intuitive operation with waterproof silicon keys
Easy to install and configure
Low-profile glass helm design
Displays and converts many J1939 SPN’s
Configurable data types for digital values and sidebars
Fuel usage and fuel economy monitoring
|
1054.80 |
|
|
AM/FM Stereo w/DVD, CD, USB, SD, & Bluetooth
The Majestic DVD5800 is the latest addition to the audio video product line up. It was specifically developed for the mobile environment, the DVD5800 boasts a powerful 4x45 Watt amplifier to give you a true rich clear sound.
With multiple inputs such as, USB, SD Card slot in the front and Aux Audio Video input from the rear, this unit gives you the power to playback audio or video from most of the major media devices.
The DVD5800 was also designed with an easy access Audio Aux Input in the front to allow simple audio input from your portable media player. Simply plug your iPhone or iPad into the Aux input and the sound will come through to your speaker system
To push the feature limits further, the DVD5800 has built in Bluetooth to allow phone connectivity. So when you are looking for a feature packed DVD player with AM/FM/CD/DVD/MP3/MP4 and much more, then the Majestic DVD5800 is your ultimate choice.
Outputs:
2x Video
1x Audio
4x45 Watts
Inputs Front:
Audio Aux
USB
SD Card
CD/DVD Disc
Features:
Voltage Range: 10.9V to 15V DC
Size: Standard Din
Inputs: Audio Input - Front, USB, SD Card
Formats: MP3, MP4, DivX, Jpeg, and many others
Features: 2 Video Outputs, 1 Audio Input
Current Draw @ 12 Volts: 3.5A (average)
Color: Black Face
Accessories Supplied: Power Cable, Remote Control, Mounting Kit, Instruction Manual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
211.70 |
|
|
52 MM (2-1/16") ViewLine - Voltmeter 8 to 16V - White w/Chrome Bezel
Veratron ViewLine offers a comprehensive modular, modern series of instruments for engine monitoring.
More functions and greater flexibility in installation and design increase the scope for high manufacturing standards and guarantee the highest level of reliability and readability. As the result of ongoing research and development work, we offer an innovative comprehensive standard instrumentation platform which is also available for outboard engine use. ViewLine provides maximum freedom to customize the cockpit and is the natural choice for an attractive price/performance ratio.
The ViewLine 52 mm Gauges are available in black or white dial versions, which are always completed with a round bezel in identical color.
Interchangeable bezel option.
Features:
8 pole Tyco/Hirschmann MQS plug
Red LED Via Plus And Min Warning Light
Operating voltage 12 - 24 V
Input signal: standard Ω values
Optional make-point switch can be connected
Reverse polarity protection
Anti-fog double lens
Front side protection rating IP67
52 mm installation diameter
50 mm installation depth
In the Box:
Gauge
Connection Cable
Bezel
Rubber Seal
Spinlock
Installation Instructions
Safety Instructions
*Sold as an Individual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
33.59 |
|