|
SPAPOWER9 Water Resistant Power Supply
ProSpec's SPA-POWER9 regulated power supply boast an IPx5 water-resistant rating to withstand the toughest conditions while providing electricity to the 12-volt stereo in your spa or hot tub. It's UL-rated and offers up to 10 amps of output current.
In addition to its tough outer shell, the SPA-POWER9 power supply includes protection against short circuits, over-current, and over-temperature. The output section includes two pre-crimped slide connectors to attach to your spa stereo.
Features:
Water-resistant AC-to-DC power supply for spa stereos
Can be directly hard-wired to AC power
IPx5 rating
Wall/panel mountable
Dimensions (H x W x D) - 12" x 5-5/8" x 3"
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
91.76 |
|
|
Power Supply for NavNet 3D and TZtouch
The PSU012 Power Supply is required for DRS4A and DRS6A with MFD8, DRS12A with MFD8 or MFD12. The PSU012 Power Supply is required for DRS2D, DRS4D, DRS4A, DRS6A and DRS12A with TZT9 or TZT14.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
908.18 |
|
|
Desktop Switching Power Supply - 120VAC Input, 12V Output, 10 Amp
This high efficiency UL-60950-1 approved AC-DC power converter provides a highly regulated output DC voltage of 13.8 Volts at 10 Amps with an AC input of 120 Volts, 60 Hz (230 Volts, 50 Hz model also available). These advanced switch-mode DC power supplies were designed specifically for use with land mobile radio. The power supplies produce clean reliable power and are highly filtered to suppress RFI. The unit comes with a detachable power supply cord with NEMA 5-15P plug. Features include over-current, short-circuit and over-voltage protection. The AC-DC power supply conforms to FCC Part 15(B), class B digital device.
Features:
Advanced switch-mode technology
Reliable power with minimum weight and size
Circuit innovations minimize output voltage ripple and RFI
Input voltage can be set at 120VAC or 240VAC (internal jumper)
UL listed to both USA & Canadian safety standards
Specifications:
Input: 100-130 VAC
Output: 13.8 VDC
Amps: 10 Amps
Fuse: 3 Amps
Weight: 3.4 (lbs)
Weight: 1.54 (kg)
Dimensions: 8.19 x 7.28 x 2.4 (in)
Dimensions: 20.8 x 18.5 x 6.1 (cm)
Safety: UL, FCC
Warranty: 3 Year Limited
Applications:
Two way radio base stations
Communications systems
Security systems
Test equipment
Plotters
GPS receivers
Automotive & Marine displays
DC computers
12 Volt lighting systems
OEM applications
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
121.91 |
|
|
Kraken Secondary Power Supply with Opto-Coupler
Features:
Connect up to 5 Kraken underwater lights.
480W power supply included.
Includes all bus connectors and breakers.
Two Opto-Couplers included (signal booster/breaker)
Can connect two Poco channels per box.
Weatherproof enclosure
|
1580.42 |
|
|
LunaSafe 10W Qi Charge Pad USB Powered - Power Supply Not Included
Only 5mm thick, the slimmest wireless charger available. Durable mirror panel and aviation aluminum. Built-in over-charging, over-heating, and short-circuit protection. The LED indicator lets you know the charging status. Supports all Luna-Safe products and even works on enabled wireless charging devices such as your cell phones.
Features:
Only 5mm Thick
LED shows charging status
Can charge other wireless devices
5V 2A power supply not included
|
16.46 |
|
|
SEC-1223 Power Supply
This high-efficiency UL-60950-1 approved AC-DC power converter provides a highly regulated output DC voltage of 13.8 Volts at 23 Amps with an AC input of 120 Volts, 60 Hz. These advanced switch-mode DC power supplies were designed specifically for land mobile radio (LMR) applications. The power supplies produce clean reliable power and are highly filtered to suppress RFI. The unit comes with a detachable power supply cord with NEMA 5-15P plug. Features include over-current, short-circuit, and over-voltage protection. The AC-DC switching power supply conforms to FCC Part 15(B), class B digital device.
Features:
Advanced switch-mode technology
Reliable power with minimum weight and size
Circuit innovations minimize output voltage ripple and RFI
Input voltage can be set at 120VAC or 240VAC (internal jumper)
UL listed to both USA & Canadian safety standards
Specifications:
Input: 100-130 VAC
Output: 13.8 VDC
Amps: 23 Amps
Fuse: 6.3 Amps
Weight: 3.5 (lbs)/1.6 (kg)
Dimensions: 7.28 x 8.19 x 2.40 (in)/18.5 x 20.8 x 6.1 (cm)
Safety: UL, FCC
Applications:
Two way radio base stations
Communications systems
Security systems
Test equipment
Plotters
GPS receivers
Automotive & Marine displays
DC computers
12 Volt lighting systems
OEM applications
|
144.13 |
|
|
115-24-10 Power Supply
This super-rugged DC power supply is ideal for powering 24-volt communication and navigation equipment onboard commercial vessels where reliability is essential. The proven linear circuit design provides pure noise-free output and a long service life.
Features:
Excellent Regulation and Ripple Spec (output voltage maintained within 1% under all rated line and load conditions)
Polyurethane conformal coated PC board and corrosion-resistant heavy-duty aluminum case with integral shock mounts assure survival in hostile environments
The heat generated by semi-conductors is extracted and dissipated by large heat sink fins for cool operation
Protection: overvoltage, current limit; (set @ 105% of intermittent rating), thermal overload, and input/output fusing
Thermally activated cooling fan on “CD” units
Specifications:
Nominal Input/VAC: 115/230
Maximum Input Current @115: 5.5
Maximum Input Current @230: 2.5
Output Amperage (Intermittent): 10
Output Amperage (Continuous): 4
Weight: 20 lbs. / 9.1 kg
Case Size:
H x W x D (inch): 5.7” x 4.8” x 16.3”
Input Range
105-125/210-250 VAC (selectable), 50-60 Hz; Derate to 50% output below 110 and 220 VAC
Operating Temperature
Standard Units - 0-50 degrees C, Derate linearly from 100% @ 40 degrees C to 50% @ 50 degrees C thermal shutdown @ 85 degrees C case temperature
Duty Cycle:
Intermittent: 20 minutes max on time, 20% duty
Continuous: 24 hours/day 100% Duty
Options:
Modify for use as a battery charger
The output voltage is adjusted (see Output Voltage for range)
Transfer relay for back-up battery in event of power failure (ERC option)
Output Voltage:
24.5 VDC (Internally adjustable 21-27.5 VDC)
Ripple: 70mV P-P (@ 110-125 / 220-250 VAC input)
1% Line and Load (@ 110-125 / 220-250 VAC input)
Mechanical:
Powder-coated aluminum heat sink case
Front panel terminal block
Heavy-duty mounting flange
Conformal-coated PC board
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1053.23 |
|
|
Power Supply
Furuno's power supply is used specifically for Furuno's 1964C.
Features:
25kW
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1412.72 |
|
|
NN3D Power Supply for 25W Radars
The PSU013 Power Supply is required for all DRS25A installations and is included iwth the DRS25A.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1112.72 |
|
|
Power Supply 110AC to 12DC/70A
The PWS1000 Series of power supplies provides 12, 24 or 48 Volts DC at 1000 Watts of continuous power from a 110 or 220 Volt AC source.
Analytic Systems’ power supplies use Switchmode technology with powerful IGBT switching transistors for reliability and efficiency with minimum size. Circuit innovations reduce output ripple to levels previously available only from bulky and inefficient linear power supplies. Reliability features include an input fuse, thermal shutdown, current limiting and output short circuit protection with automatic recovery. An Output Over voltage Crowbar circuit protects any powered devices from excessive voltage in the event of a failure of the unit.
The newly updated single-board PWS1000 is ultra-quiet and features the latest generation of current mode PWM control. Extra features include adjustable output voltage audible and visual indicators for low input voltage, low output voltage, over temperature, overload and output on. Either 110 or 220 VAC input (Field Convertible) is available. The PWS1000 also features a four contact output terminal (two positive and two negative contacts) for easy connection of devices to the supply.
Features:
Power sensitive electronics without interference
Rugged and reliable to ensure years of safe and trouble free operation
Adjustable output voltage
Extremely rugged and well suited for marine and other demanding environments
Ultra-quiet low EMI operation
Audible & visual indicators for output overload, low input voltage, low output voltage & over-temperature
Over-temperature shutdown
Current limiting
Short circuit protection
Output overvoltage crowbar
Dry contact output fail relay
Remote control option
Digital Volt/Ammeter option
Custom output voltages available (8V to 55V)
19” Rackmount Available
Parallel output diodes available
Three year parts and labour warranty
|
1182.77 |
|
|
Power Supply 110AC to 24DC/40A
The PWS1000 Series of power supplies provides 12, 24 or 48 Volts DC at 1000 Watts of continuous power from a 110 or 220 Volt AC source.
Analytic Systems’ power supplies use Switchmode technology with powerful IGBT switching transistors for reliability and efficiency with minimum size. Circuit innovations reduce output ripple to levels previously available only from bulky and inefficient linear power supplies. Reliability features include an input fuse, thermal shutdown, current limiting and output short circuit protection with automatic recovery. An Output Over voltage Crowbar circuit protects any powered devices from excessive voltage in the event of a failure of the unit.
The newly updated single-board PWS1000 is ultra-quiet and features the latest generation of current mode PWM control. Extra features include adjustable output voltage audible and visual indicators for low input voltage, low output voltage, over temperature, overload and output on. Either 110 or 220 VAC input (Field Convertible) is available. The PWS1000 also features a four contact output terminal (two positive and two negative contacts) for easy connection of devices to the supply.
Features:
Power sensitive electronics without interference
Rugged and reliable to ensure years of safe and trouble free operation
Adjustable output voltage
Extremely rugged and well suited for marine and other demanding environments
Ultra-quiet low EMI operation
Audible & visual indicators for output overload, low input voltage, low output voltage & over-temperature
Over-temperature shutdown
Current limiting
Short circuit protection
Output overvoltage crowbar
Dry contact output fail relay
Remote control option
Digital Volt/Ammeter option
Custom output voltages available (8V to 55V)
19” Rackmount Available
Parallel output diodes available
Three year parts and labour warranty
|
1182.77 |
|
|
100 Amp 125/250V 3-Pole, 4-Wire Cordset - No Neutral Wire- One-Ended Male Only Power Supply - Blunt Cut - 100'
All Marinco cordsets are made of the highest quality, marine grade construction with features you won’t find on other power cords.
Features:
For use with 100 amp 125V/250V shore power systems
High visibility, 2 AWG, flexible yellow STOW cable is oil, water, UV resistant, and rated to 221°F (105°C)
Ergonomic non-slip TPE coated gripping surfaces
IEC pin and sleeve plugs and connectors are designed for harsh environments, watertight, and corrosion resistant. Feature integrated locking rings.
Internal frame terminals provide high clamping force for safe and secure contact
Options for use with on-board isolation transformers, male plug only power supply, and extension purposes
UL and ABYC approved components
Specifications:
Length: 100'
Neutral Wire: No
Female End: No, Blunt Cut
Application: Cable Winch with Isolation Transformer
Color: Yellow
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
2551.39 |
|
|
100 Amp 125/250V 3-Pole, 4-Wire Cordset - No Neutral Wire- One-Ended Male Only Power Supply - Blunt Cut - 125'
All Marinco cordsets are made of the highest quality, marine grade construction with features you won’t find on other power cords.
Features:
For use with 100 amp 125V/250V shore power systems
High visibility, 2 AWG, flexible yellow STOW cable is oil, water, UV resistant, and rated to 221°F (105°C)
Ergonomic non-slip TPE coated gripping surfaces
IEC pin and sleeve plugs and connectors are designed for harsh environments, watertight, and corrosion resistant. Feature integrated locking rings.
Internal frame terminals provide high clamping force for safe and secure contact
Options for use with on-board isolation transformers, male plug only power supply, and extension purposes
UL and ABYC approved components
Specifications:
Length: 125'
Neutral Wire: No
Female End: No, Blunt Cut
Application: Cable Winch with Isolation Transformer
Color: Yellow
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
3042.54 |
|
|
100 Amp, 125/250V One-Ended Male Power Supply Cable - 100'
All Marinco cordsets are made of the highest quality, marine grade construction with features you won't find on other power cords.
Features:
For use with 100 Amp, 125/250V Shore Power Systems
High visibility, 2 AWG, flexible yellow STOW cable is oil, water, UV resistant and rated to 105 degrees Celsius
IEC pin and sleeve plugs and connectors are designed for harsh environments, watertight and corrosion resistant
Feature integrated locking rings
Options for use with on-board isolation transformers, male plug only power supply and extension purposes
UL and ABYC approved
Neutral Wire: Yes
Length: 100'
Female End: No, Blunt Cut
Application: Cable winch
Color: Yellow
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
3945.01 |
|
|
Dual Qi Charge Pad - USB Powered
Only 10mm thick, the slimmest wireless charger available. Built-in over-charging, over-heating and short-circuit protection. The LED indicator lets you know the charging status. Dual 5W pads. Supports all Luna-Safe products and even works on enabled wireless charging devices such as your cell phones.
Features:
LED shows charging status
Can charge other wireless devices
5V 2A power supply not included
|
30.29 |
|