|
Steering Trim Control Unit
Trim Switches on the Steering Wheel Improve Safety and Performance.
This steering trim control unit is molded of black plastic with raised white letters to not only enhance boat appearance but also provide the ultimate in control of any high performance boat. The steering trim control unit mounts easily to steering wheel spokes to place engine trim control at your finger tips for maximum safety and ease of operation. The weather proof, rubber booted, push button switches combined with a black urethane coiled cord provide a unit which will provide trim control without removing hands from steering wheel.
Features:
Puts trim switches on steering wheel for convenience and safety
Allows driver to keep both hands on the steering wheel
Mounts easily on steering wheel spokes
Weatherproof rubber booted switches
Rugged urethane coiled cord
Can be used for trim control or jack plate control
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
108.10 |
|
|
Transom Trim Control Push Button Trim Switch
Transom Trim Control Switch/Hydraulic Jack Plate Switch
Put a trim switch or hydraulic jack plate anywhere you want with this versatile switch. The Transom Trim Control Switch provides a weatherproof tilt control system at the stern area of the boat to facilitate placing motor support in position with one person. Switch can also be used for remote adjustment of hydraulic jack plates. The switch housing is molded black plastic with raised white letters and may be mounted on any flat surface, comes with 18" pigtail wire and installation instructions.
Features:
Trim switch for outboards or stern drives
Hydraulic jack plate switch
Puts Tilt & Trim Control Anywhere
Weatherproof Control Switches
UV stable molded housing
Can Also Operate Power Jack Plates
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
49.16 |
|
|
Bennett Trim Tabs on Sale in April at CLR Marine
Bennett Trim Tab Kit with Euro-Style Rocker Switch
Now until April 30, 2012, Bennett Trim Tab Kits are on sale with an additional 10% off on all sets with Euro controls.
Bennett Standard Trim Tab Kits are ideal for cruisers who want to optimize performance over a broad range of sea conditions. The Euro-Style Rocker Switch is included with these trim tab sets. Kits are complete with all the necessary components for installation.
Bennett Trim Tab Kit with Electronic Indicator Control (EIC)
Bennett Trim Tab EIC Sets have been discounted for 2012 - that's a 25% savings on the cost of an EIC5000 when purchased in the set.
These kits contain two stainless steel trim tabs, two preasembled actuators with sensors, a hydraulic power unit, Electronic Indicator Control (EIC) all necessary wiring, tubing, hardware and installation instructions.
3-in-1: : The Electronic Indicator Control saves space on the helm by combining three features into one sophisticated control - the popular Bennett rocker switch control, trim tab indicator and the Auto Tab Retractor. Water resistant, highly accurate and features variable intensity LEDs for night or day. The Auto Tab Retractor automatically retracts the tabs when the boat's ignition is turned off. This especially protects trailered or dry storage boats from getting trim tab damage during storing, hauling and trailering.
Bennett Trim Tab AC3000 Keypad
ATC-Ready: The EIC is also designed to connect easily with another innovative product, the Auto Tab Control (ATC). The ATC plugs right into the EIC Relay Module, interacting directly with the trim tab system to automatically monitor and maintain the perfect cruising attitude. The result is an optimum ride and significant fuel savings.
The Bennett Advantage: A trim tab system that is quiet, responsive, low-maintenance, and a great long-term value, with a 5-year warranty that Bennett stands behind without hassles or headaches.
|
|
|
Lenco Automatic Trim Tab Control System
A real automatic boat control/trim tab control system that actually works - completely and automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again. The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.
Closeouts Rebates Remanufactured Specials
|
|
|
Insta-Trim 10" x 10" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
576.13 |
|
|
Insta-Trim 12" x 12" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
579.54 |
|
|
Insta-Trim 18" x 11" Trim Tab Set
Insta-Trim, the original hydraulic boat leveler, provides a better ride every time you leave the dock. Each Insta-Trim system features:
Wiring: Color-coded wiring in 25' and 40' lengths with quick connect fittings, meets federal standards for heat, pull and insulation.
Solenoids: Our solenoids are custom designed for Insta-Trim Boat Leveler company, epoxy sealed and humidity resistant, thereby preventing shorting out. The solenoids lock the tabs in any position, eliminating drift back. Barb type hose fittings provide tight, secure connections.
Motor: A powerhouse with coated wiring that resists temperature and amperage build-up. 1 3/4" stack windings and top mounting eliminates oil leakage. The motor is mounted with stainless steel nuts and bolts, and is easily disassembled. One pint of Insta-Trim biodegradable transmission oil, funnel and mounting hardware is supplied.
Pump: Designed and engineered exclusively by Insta-Trim. The built-in bypass is factory set at 400 P.S.I. Tolerance held to +/-.00025. Amperage doesn?t exceed 16 because the unit circulates oil, rather than stalling out or trying to pump additional pressure.
Brackets: Swivel type brackets allow cylinders to be mounted and adjusted to any angle. Knockout pins act as shear pins if the tab strikes an object.
Cylinders: Impact resistant, fiberglass reinforced nylon cylinders eliminates expansion and resists ultra-violet rays. Two expanding type seals, plus 0-rings, eliminates high and low pressure leaks. Barbed cylinder fitting and an inserted tubular steel rod prevents hose blow-off and breakage. A stainless steel spring retracts the cylinder when the boat is not in motion.
Stainless Steel Trim Tabs: 12 gauge 304 stainless steel trim tabs are available in standard and custom lengths. They are guaranteed against electrolysis, remaining strong and secure. Insta-Trim systems use hinges that prevent most spray and can be used for transom or bottom mounting.
Motor cover: High impact abs plastic cover with a built-in oil reservoir mounts easily with two screws. Our cover protects the motor from occasional wash down.
Hose: Designed and manufactured exclusively for Insta-Trim with nylon reinforced webbing and a UV resistant coating. Rated at 2000 lbs. Burst pressure, 15; of hose is supplied for your system. Stainless steel clamps hold the hose to barb fittings at the solenoids and at the cylinder connection.
Rocker type controls: Mounted on the dash, they are easy to operate.
Optional touch button waterproof switches: Adjust the tabs for maximum control and performance. 3" Diameter.
|
636.82 |
|
|
Flex Trim
Length: 25'
"A": 5/32"
"B": 9/16"
Color: Black
TACO Metals supplies quality trim that is designed to protect boat interiors and exteriors from the harsh marine environment.
Trim & Moulding
Trim and moulding products provide finish, protection and structural integrity. TACO trim and moulding products are the best in the industry and are used extensively throughout boat interiors and exteriors.
Materials
Depending on the product line, TACO's trim and moulding products are offered in aluminum, vinyl and specially formulated rubber compounds. TACO insists on using prime billet 6000 series aluminum alloys to ensure superior structural strength, precise bending and long-lasting performance. Vinyl and plastic products are made from prime resin and warranted for 5 years.
Covers unfinished edges and follows almost any contour or radius
Made of flexible PVC
Integrated interior aluminum clip and gripping tongue ensures a better fit
|
59.33 |
|
|
Flex Trim
Length: 25'
"A": 1/4"
"B": 1/2"
Color: Black
TACO Metals supplies quality trim that is designed to protect boat interiors and exteriors from the harsh marine environment.
Trim & Moulding
Trim and moulding products provide finish, protection and structural integrity. TACO trim and moulding products are the best in the industry and are used extensively throughout boat interiors and exteriors.
Materials
Depending on the product line, TACO's trim and moulding products are offered in aluminum, vinyl and specially formulated rubber compounds. TACO insists on using prime billet 6000 series aluminum alloys to ensure superior structural strength, precise bending and long-lasting performance. Vinyl and plastic products are made from prime resin and warranted for 5 years.
Covers unfinished edges and follows almost any contour or radius
Made of flexible PVC
Integrated interior aluminum clip and gripping tongue ensures a better fit
|
59.33 |
|
|
Flex Trim
Length: 25'
"A": 3/8"
"B": 5/8"
Color: Black
TACO Metals supplies quality trim that is designed to protect boat interiors and exteriors from the harsh marine environment.
Trim & Moulding
Trim and moulding products provide finish, protection and structural integrity. TACO trim and moulding products are the best in the industry and are used extensively throughout boat interiors and exteriors.
Materials
Depending on the product line, TACO's trim and moulding products are offered in aluminum, vinyl and specially formulated rubber compounds. TACO insists on using prime billet 6000 series aluminum alloys to ensure superior structural strength, precise bending and long-lasting performance. Vinyl and plastic products are made from prime resin and warranted for 5 years.
Covers unfinished edges and follows almost any contour or radius
Made of flexible PVC
Integrated interior aluminum clip and gripping tongue ensures a better fit
|
66.94 |
|
|
Flex Trim
Length: 25'
"A": 1/2"
"B": 5/8"
Color: Black
TACO Metals supplies quality trim that is designed to protect boat interiors and exteriors from the harsh marine environment.
Trim & Moulding
Trim and moulding products provide finish, protection and structural integrity. TACO trim and moulding products are the best in the industry and are used extensively throughout boat interiors and exteriors.
Materials
Depending on the product line, TACO's trim and moulding products are offered in aluminum, vinyl and specially formulated rubber compounds. TACO insists on using prime billet 6000 series aluminum alloys to ensure superior structural strength, precise bending and long-lasting performance. Vinyl and plastic products are made from prime resin and warranted for 5 years.
Covers unfinished edges and follows almost any contour or radius
Made of flexible PVC
Integrated interior aluminum clip and gripping tongue ensures a better fit
|
66.98 |
|
|
Shurflo 8020-513-236 Pump 115V 60Sw Pvs
Shurflo- Diaphragm Pump 3 Chamber, 1.5 GPM Open Flow, 115VAC Intermittent Duty, 60 PSI Demand Switch (adjustable 40-60 PSI), Viton Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, Has a Power Cord, UL/CSA Recognized, General Industrial Pump
|
246.75 |
|
|
SP-80 - Control Head Only
For boaters who know where they're going. SP-80 takes you where you want to be--effortlessly. Its smart, precise piloting gives you the extra hand on deck you've always needed. And the operation is a snap: Simply set the course and the SP-80 takes the controls, piloting you to your destination with ease and precision. So bait the lines or simply enjoy the sunset. With the SI-TEX SP-80 Autopilot you're right on course. Hands free, and ready to go.
Features:
Designed for Outboard, Inboard, and Sterndrive vessels with Hydraulic or Mechanical steering systems.
Automatically pilots to your next waypoint using built-in NMEA 0183 Loran/GPS interface.
Waterproof control head easily installs flush or surface mounted.
System can be expanded by adding fully functional second-station option with the SI-TEX SP-70 Handheld Control Unit.
Bold, backlit display with ten levels of brightness for clear reading in any light.
Accurate digital displays of rudder angle and operating mode in use, constantly giving you up-to-the minute operating status.
Automatic Sea State and Trim controls and 10 selectable levels of rudder sensitivity with high and low speed settings for smooth, precise steering.
Rudder feedback verifies autopilot's commands.
Ghost Rudder backup allows autopilot to use memory of rudder movements to calculate new movements in event of rudder feedback failure.
Heading Output feature allows you to stabilize radar display.
Built-in diagnostics and self tests, plus visual and audible alarms.
Power Steering mode offers convenient push-button steering. Stand-By mode for manual steering situations.
Optional analog Rudder Angle Indicator for easy, at-a-glance reading of exact rudder position.
Works with solenoid valves also.
|
588.00 |
|
|
Max Control Holding Tank Deodorant - 1-Gallon
Max Control Advanced formaldehyde-free formula. Long lasting treatment eliminates and controls holding tank odors by breaking down waste and toilet tissue.
Features:
4 ounces treats a 40 gallon holding tank
Formaldehyde-Free Formula
Easy to use. See-through window stripe and 8-oz. increment marks make measuring easy
One (1) Gallon container
New Item # 9108557756
*Sold by the Gallon
WARNING: This product can expose you to chemicals including ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
34.01 |
|
|
Max Control Holding Tank Deodorant - 32oz Bottle
Max Control Advanced formaldehyde-free formula. Long lasting treatment eliminates and controls holding tank odors by breaking down waste and toilet tissue.
Features:
4 ounces treats a 40 gallon holding tank
Formaldehyde-Free Formula
Easy to use. See-through window stripe and 8-oz. increment marks make measuring easy
32 oz. Container
New Item # 9108557757
*Sold by the 32 oz. Container
WARNING: This product can expose you to chemicals including ARSENIC which is known to the State of California to cause cancer or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
15.96 |
|