|
Hypro 6500N-R, Roller Pump Ni-Resiet Rev
Hypro 6500N-R 6-Roller Pump, REVERSED, With Ni-Cast Case, Super Rollers, Viton Seals, 3/4" NPT Ports, Solid 5/8" Shaft. Great for pest control applications.
HYPRO NI-RESIST Roller Pump. High volume and pressure. For livestock spraying, fertilizer application, weed and pest control. Spray wettable powders and chemicals. CCW (reverse by disassembling and reversing rotor in housing).
NI-RESIST for more corrosive chemicals. NI-RESIST features high nickle content to give longer life.
Performance Information
• Max. flow:- 9.7 gpm/36.7 lpm at 540 rpm- 18.2 gpm/68.9 lpm at 1000 rpm- 21.8 gpm/82.5 lpm at 1200 rpm
• Max. pressure:- Continuous 100-150 psi/6.9-10.3 bar- Intermittent 300 psi/20.7 bar
• Max. rated speed: 1200 rpm
• Max. fluid temperature: 140°F/60°C
|
565.21 |
|
|
Little Giant Manual Submersible Sump Pump 506271
Little Giant 6-CIM-R Manual Submersible Sump Pump
Motor 115 Volt 60 Hz 1/3 HP Permanently Lubricated Oil Filled Continuous Duty Motor, 46 GPM at 5 Foot Head, Shutoff Head 18 Feet, Inlet: Screened, Outlet: 1-1/2" FNPT with 1-1/4" FNPT and Male Garden Hose Adaptors, Epoxy Coated Cast Iron Housing, Polypropylene Body, Mechanical Seal, Manual Operation, UL/CSA Listed, 10 Foot Power Cord
506271 For residential and light commercial use, the manual 6-CIM-R submersible sump pump provides efficient and reliable service.
|
290.16 |
|
|
Sherwood R-10870G WESTERBEKE PUMP 11353
Pump Body: Bronze
Ports: 3/4" NPT
Cam: Full
Impeller: Neoprene
Shaft Seal: Mechanical
Drive: Pulley Driven Pedestal Pump
Keyed Shaft
Universal and Westerbeke Light Plants Government Light Boats 11353 38445
|
903.80 |
|
|
Hypro 7560N-R, Roller Pump Ni-Resist Rev
Ni-Resist 8-Roller Pump w/ Super Rollers, Super Rotor, Viton Seals, 20.1 GPM, 300PSI, 1000RPM, 3/4" NPT, 15/16" Shaft
Performance Information
Max. flow: 12 gpm/45.4 lpm at 540 rpm
Max. flow: 22.5 gpm/85.2 lpm at 1000 rpm
Max. pressure: continuous 100 psi/6.9 bar
Max. pressure: intermittent 300 psi/20.7 bar
Max. rated speed: 1000 rpm
Max. fluid temperature: 140°F/60°C
Other Attributes
Rollers: Super Rollers standard (Poly, Teflon and Buna-N available)
Housing: Cast Iron, Ni-Resist or Silvercast
Port sizes: 3⁄4" NPT
Shaft: 15⁄16" solid
Shaft rotation: CW
1" hose barb inlet fitting for 1000 rpm operation
Shaft Seals: Viton standard (Buna-N available)
Available PTO adapters
Rotor: Cast Iron, Ni-Resist and Silvercast
Recommended PTO torque arm kit 3430-0540
|
636.39 |
|
|
Sherwood R-102 General Purpose Pump
Pump Body: Bronze
Ports: 1" NPT
Cam: Full
Impeller: Neoprene
Shaft Seal: Mechanical
Drive: Pulley Driven Pedestal Pump
Flexible Impeller General Purpose Engine Cooling Pump
|
643.75 |
|
|
No matter whether you are an experienced boater looking for a replacement pump or a manufacturer specifying pumps for your marine application, we are prepared to provide you with the support you need. And no matter where you work or live, access to our products, services, spare parts and support are never far away. In fact, you will find SPX FLOW's Johnson Pump marine brand represented in every major industrial country of the world today and in more than sixty nations altogether.
SHOP JOHNSON PUMP
The Aqua Jet five chamber diaphragm pump provides the perfect water pressure or deck wash solution for both small and medium sized leisure and commercial boats as well as mobile homes, campers and summer homes.
Quiet and pulsation-free even at low speeds. Efficient and compact, Aqua Jet pumps are particularly suitable where low amperage and sound levels in relation to water flow are placed at a premium-such as in shower and galley applications. Integrated pressure switch turns pump on and off automatically when tap is opened and closed. Operates in fresh or sea water.
SHOP THE Aqua Jet five chamber diaphragm pump
Specials Closeouts Remanufactured Rebates
|
|
|
Roper Pump 18AM08 Pump Flange Mounted W/Relief
Roper A Series Gear Pump, model 18AM08
Housing : Cast Iron
Gears : Ductile Iron
Bearings : Bronze
Idler Shafts : Ductile Iron
Drive Shafts : Hardened Steel
This is a general purpose Roper A series Pump for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer. The Roper A Series pumps are adaptable to a wide range of applications pumping clean fluids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer. These pumps are designed to operate at standard motor speeds, with provisions for flange or foot mounting.
|
1595.70 |
|
|
Roper Pump 18AM02-2B A Series Gear Pump W/Rv
Ports: 3/8 in.
Flow-Rate: 7.2 GPM
Max RPM: 3600
GPR: .002
Mtg: Flange
Roper A Series pumps are adaptable to a wide range of applications pumping clean ?uids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer.
These pumps are designed to operate at standard motor speeds, with provisions for ?ange or foot mounting. The internal bearings are lubricated by the ?uid being pumped. With only two moving parts, the pumps run quietly.
3/8" and 3/4" pumps are 300 PSI and all 1 1/4" - 2" pumps are 150 PSI
Specifications
Type of Pump: Positive Displacement Gear Pump
Materials of Construction: Cast Iron Housing, Ductile Iron Gears and Drive Shafts, Bronze Bearings and Steel Idler Shafts.
Priming: Self Priming
Seal Material: Mechanical Seal (AM)
Viscosity: Up to 2,200 cSt, 10,000 SSU
|
770.40 |
|
|
Autopilot Pump Type 1 Adjustable Reversing 12V Up To 15 CI Cylinder
TWICE THE POWER
The unique Octopus piston pump delivers over twice the hydraulic output per watt of input than a standard hydraulic gear pump.
HALF THE POWER CONSUMPTION
Gear pumps leak oil between the gears, while a piston (such as used in car engines) does not. This means the piston pump will place the cylinder ram exactly where it is required, positioning the rudder accurately. This gives far sharper steering, reducingunnecessary course corrections meaning battery consumption on Octopus pumps is up to half that of other pumps.
PINPOINT ACCURACY
Leading autopilot manufacturers choose Octopus pumps for their non RFB pilot systems which do not have a Rudder Feedback unit. Previously, slop in the system caused by gear leakage meant that a Rudder Feedback unit was necessary to tell the pilot the exact rudder position. As Octopus pumps will always bring the ram back to the required position the Rudder Feedback unit is not required, which also greatly simplifies installation.
SAVE ON INSTALLATION COSTS
A professional installation should always have a method of isolating the pump from the steering system - Octopus pumps feature inbuilt shut off valves in the pump manifold.
ADJUSTABLE FLOW RATE
A pump that does not have variable flow (unless dedicated to a range of cylinders such as our fixed 0.8L pump) will be operating too fast or too slow in 90% of cases. Autopilot manufacturers get around this problem by adjusting the output to the pump to compensate, which either forces the pump to operate for longer periods of time which increases power consumption and wear on the parts, or it will operate at high pressure for short periods of time - also putting unnecessary strain and wear on the system.
Octopus Variable Flow Reversing Pumps precisely control the speed of the ram, reducing unnecessary battery consumption, pressure, strain and wear on the hydraulic system.
Getting the best steering performance for the boat. The flow rate of the pump can be set to get the best hard over time (cylinder ram speed) for the particular boat.
Features:
Reliable - Piston pump technology with only three moving parts
Twice the Power - Delivers over twice the hydraulic output per watt of input
Half the Power Consumption - Accurate ram positioning means fewer course corrections
Adjustable Flow Rate - Configure performance to suit your vessel
Easy Servicing - Shut off valves allow removal without draining steering system
|
522.79 |
|
|
Autopilot Pump Type 3 Adjustable Reversing 12V Up to 30CI Cylinder
Features:
RELIABLE - Piston pump technology with only three moving parts
TWIC THE POWER - Delivers over twice the hydraulic output per watt of input
HALF THE POWER CONSUMPTION - Accurate ram positioning means fewer course corrections
ADJUSTABLE FLOW RATE - Configure performance to suit your vessel
EASY SERVICING - Shut off valves allow removal without draining steering system
TWICE THE POWER
The unique Octopus piston pump delivers over twice the hydraulic output per watt of input than a standard hydraulic gear pump.
HALF THE POWER CONSUMPTION
Gear pumps leak oil between the gears, while a piston (such as used in car engines) does not. This means the piston pump will place the cylinder ram exactly where it is required, positioning the rudder accurately. This gives far sharper steering, reducingunnecessary course corrections meaning battery consumption on Octopus pumps is up to half that of other pumps.
PINPOINT ACCURACY
Leading autopilot manufacturers choose Octopus pumps for their non RFB pilot systems which do not have a Rudder Feedback unit. Previously, slop in the system caused by gear leakage meant that a Rudder Feedback unit was necessary to tell the pilot the exact rudder position. As Octopus pumps will always bring the ram back to the required position the Rudder Feedback unit is not required, which also greatly simplifies installation.
SAVE ON INSTALLATION COSTS
A professional installation should always have a method of isolating the pump from the steering system - Octopus pumps feature inbuilt shut off valves in the pump manifold.
ADJUSTABLE FLOW RATE
A pump that does not have variable flow (unless dedicated to a range of cylinders such as our fixed 0.8L pump) will be operating too fast or too slow in 90% of cases. Autopilot manufacturers get around this problem by adjusting the output to the pump to compensate, which either forces the pump to operate for longer periods of time which increases power consumption and wear on the parts, or it will operate at high pressure for short periods of time - also putting unnecessary strain and wear on the system.
Octopus Variable Flow Reversing Pumps precisely control the speed of the ram, reducing unnecessary battery consumption, pressure, strain and wear on the hydraulic system.
|
810.47 |
|
|
Roper Pump 3711HBFRV Gear Pump W/Mech Seal
Features
Heavy duty cast iron helical gear pumps
Bi directional, self-priming
Differential pressures to 125 PSI
Up to 468 GPM
Standard operation up to 212° F
Can be built to operate up to 450° F
Maintenance-free durability
This pump operates smoothly and with equal efficiency in either direction of rotation. They effectively handle heavy, viscous materials such as asphalt, molasses, roofing compounds, and printing inks, as well as fuel oils, gasolines, and similar thin liquids. Pumps can be supplied in several materials of construction, with or without built-in relief valves. Pumps can be assembled either hi-drive or low-drive, and are available with conventional packed box or lapped-face mechanical shaft seal. They can be direct driven or driven through a built-in gear reduction with a wide range of ratios. These pumps operate equally well regardless of the mounting configuration or the direction of rotation.
Applications:
Mixing, blending, recirculating, and transferring heavy, viscous materials in either a fixed or mobile transfer application.
Ideal for gasoline, asphalt, molasses, ink, roofing compound, and coils.
Ships Via Truck only ask us for a shipping quote at the Contact Us page. Please provide City,State and Zip Code.
|
2055.60 |
|
|
Roper Pump 2835M High Viscous Pump W/Rv
Roper's 2835 rotary pump is built for pumping highly viscous, molasses-based liquid feed supplements.
|
1257.30 |
|
|
Oberdorfer N1000R-66 Gear Pump S6 Spec Ext R/V
FEATURES
Pump Body:
Bronze
Ports:
1/4" NPT
Flow:
2.1 GPM Max
Pressure:
150 PSI Max
Bearings:
Heavy Duty Carbon Bearings (Self Lubricating)
Gears:
Special Cast Bronze Helical Gears
Shaft Seal:
Formed Ring Seal Packing Standard. Optional Lip Seals or Mechanical Seals in Buna or Viton.
Shaft:
Stainless Steel Shafts
Motor / Drive:
Either direct drive with flexible coupling or pulley drive can be used. We have many motor options and can assemble for you.
APPLICATIONS / CHARACTERISTICS
BRONZE PEDESTAL MOUNT ROTARY GEAR PUMPS
Service life will be increased substantially if the liquid pumped is clean and has some degree of lubricity. Liquids compatible with bronze and stainless steel can be pumped providing proper seal has been specified. Close tolerances and the positive pumping action make the rotary gear pump capable of lifting water on the suction side as high as 20 feet.
|
525.00 |
|
|
Roper Pump 1AM03 Pump W/O Relief Valve Mech
Roper A Series Gear Pump model 1AM03
Cast Iron Housing/ Ductile Iron Gears/ Bronze Bushings/ Buna Mechanical Seal/ No Relief Valve
3/4″ NPT Ports
General Transfer Applications
|
880.20 |
|
|
Roper Pump 3611HB 2" Gear Pump Bronze Bearings N/Rv
Roper 3611HB Gear Pump
2″ NPT
Standard Fitted with Graphite Packing and Bronze Bushings
Ships via Truck
|
1283.40 |
|