Autopilot Pump Type 3 Adjustable Reversing 12V Up to 30CI Cylinder Features: RELIABLE - Piston pump technology with only three moving parts TWIC THE POWER - Delivers over twice the hydraulic output per watt of input HALF THE POWER CONSUMPTION - Accurate ram positioning means fewer course corrections ADJUSTABLE FLOW RATE - Configure performance to suit your vessel EASY SERVICING - Shut off valves allow removal without draining steering system TWICE THE POWER The unique Octopus piston pump delivers over twice the hydraulic output per watt of input than a standard hydraulic gear pump. HALF THE POWER CONSUMPTION Gear pumps leak oil between the gears, while a piston (such as used in car engines) does not.  This means the piston pump will place the cylinder ram exactly where it is required, positioning the rudder accurately.  This gives far sharper steering, reducingunnecessary course corrections meaning battery consumption on Octopus pumps is up to half that of other pumps. PINPOINT ACCURACY Leading autopilot manufacturers choose Octopus pumps for their non RFB pilot systems which do not have a Rudder Feedback unit. Previously, slop in the system caused by gear leakage meant that a Rudder Feedback unit was necessary to tell the pilot the exact rudder position. As Octopus pumps will always bring the ram back to the required position the Rudder Feedback unit is not required, which also greatly simplifies installation. SAVE ON INSTALLATION COSTS A professional installation should always have a method of isolating the pump from the steering system - Octopus pumps feature inbuilt shut off valves in the pump manifold. ADJUSTABLE FLOW RATE A pump that does not have variable flow (unless dedicated to a range of cylinders such as our fixed 0.8L pump) will be operating too fast or too slow in 90% of cases.  Autopilot manufacturers get around this problem by adjusting the output to the pump to compensate, which either forces the pump to operate for longer periods of time which increases power consumption and wear on the parts, or it will operate at high pressure for short periods of time - also putting unnecessary strain and wear on the system. Octopus Variable Flow Reversing Pumps precisely control the speed of the ram, reducing unnecessary battery consumption, pressure, strain and wear on the hydraulic system.

Autopilot Pump Type 1 Adjustable Reversing 12V Up To 15 CI Cylinder TWICE THE POWER The unique Octopus piston pump delivers over twice the hydraulic output per watt of input than a standard hydraulic gear pump. HALF THE POWER CONSUMPTION Gear pumps leak oil between the gears, while a piston (such as used in car engines) does not.  This means the piston pump will place the cylinder ram exactly where it is required, positioning the rudder accurately.  This gives far sharper steering, reducingunnecessary course corrections meaning battery consumption on Octopus pumps is up to half that of other pumps. PINPOINT ACCURACY Leading autopilot manufacturers choose Octopus pumps for their non RFB pilot systems which do not have a Rudder Feedback unit. Previously, slop in the system caused by gear leakage meant that a Rudder Feedback unit was necessary to tell the pilot the exact rudder position. As Octopus pumps will always bring the ram back to the required position the Rudder Feedback unit is not required, which also greatly simplifies installation. SAVE ON INSTALLATION COSTS A professional installation should always have a method of isolating the pump from the steering system - Octopus pumps feature inbuilt shut off valves in the pump manifold. ADJUSTABLE FLOW RATE A pump that does not have variable flow (unless dedicated to a range of cylinders such as our fixed 0.8L pump) will be operating too fast or too slow in 90% of cases.  Autopilot manufacturers get around this problem by adjusting the output to the pump to compensate, which either forces the pump to operate for longer periods of time which increases power consumption and wear on the parts, or it will operate at high pressure for short periods of time - also putting unnecessary strain and wear on the system. Octopus Variable Flow Reversing Pumps precisely control the speed of the ram, reducing unnecessary battery consumption, pressure, strain and wear on the hydraulic system. Getting the best steering performance for the boat. The flow rate of the pump can be set to get the best hard over time (cylinder ram speed) for the particular boat.  Features: Reliable - Piston pump technology with only three moving parts Twice the Power - Delivers over twice the hydraulic output per watt of input Half the Power Consumption - Accurate ram positioning means fewer course corrections Adjustable Flow Rate - Configure performance to suit your vessel Easy Servicing - Shut off valves allow removal without draining steering system

Autopilot Pump Type 2 - Adjustable Reversing Pump - 12V up to 18 CI Cylinder Now with ORB Port Connection manifold Reversing pumps are used when hydraulic steering is fitted on boats up to 65 feet L.O.A. (depending on rudder torque). The pumps are switched on by the automatic pilot and make a steering correction to left or right determined by the direction of rotation of the pump motor. The motors are of the permanent magnetic type and reversing direction is accomplished by reversing the motor input current. The pump has only three moving parts and requires no complicated check valves to prevent rudder movement when de-energized. Output flow is completely adjustable to 50% of rated flow allowing the pump output to be adjusted precisely to the volume of steering cylinder fitted. The pump is exceptionally reliable and delivers more than twice the hydraulic output per watt of input than gear pumps manufactured by competitors. Motors are heavy duty, a full 85mm in diameter with long brushes and sealed ball bearings for long service life. The molded rubber mounting foot can be rotated to allow the pump to be mounted on any surface. A useful range of accessories can be used to enhance the pump by incorporating added valves and solid state FET switching. The valves mount directly to the pump body. The FET switch mounts adjacent to the pump. No other autopilot pump made offers such advantages. Benefits of the Octopus Reversing Pumps Piston pump technology giving higher efficiency and accuracy Fewer moving parts giving increased reliability Variable flow rate to make sure the pump is matched as accurately as possible to the manual steering system Professional cut off valves for simple servicing. Features: Average Current 4-6 amps Max Current 19amps 12vDC Cylinder Size: 11-22ci Flow Rate(adjustable): 600cc - 1.2 litre/min

Linear Actuators OCTAF1212LAM12 An Octopus Hydraulic Linear Actuator is a simple, effective way to drive the rudder on a boat equipped with a mechanical steering system. The linear actuator is an assembly of an Octopus reversing pump and a marine hydraulic cylinder. This assembly is mounted on the rudder tiller-arm or quadrant. When the autopilot is not in use the cylinder runs freely along with the rudder. When the automatic pilot is in use a solenoid valve on the actuator closes and locks the cylinder. Steering signals from the pilot are now fed to the D.C. motor, which drives the pump to move the cylinder back and forth. De-energized, the solenoid valve immediately disconnects the automatic pilot from the rudder. The actuator has a small translucent oil reservoir, making it easy to check fluid levels. These actuators have only five moving parts. Mechanical simplicity gives our product reliability and ease of service when compared to complicated gear and screw actuators, making our units a favorite for offshore mariners. These actuators are shipped from our factory completely filled with oil and require no additional plumbing. Features Average Current 4-6 amps Max Current 19amps 12vDC Cylinder Bore: 38mm Variable Flow Rate: 600cc-1.2 litre/min Stroke: 305mm/12in Hardover Time(Suggested): 14-16 sec Max Rudder Torque: 1,200Nm/10,600lbin Peak Thrust: 400Kg/882lbs Max boat Length: 18m/60'

Linear Actuators OCTAF1212LAR12 An Octopus Hydraulic Linear Actuator is a simple, effective way to drive the rudder on a boat equipped with a mechanical steering system. The linear actuator is an assembly of an Octopus reversing pump and a marine hydraulic cylinder. This assembly is mounted on the rudder tiller-arm or quadrant. When the autopilot is not in use the cylinder runs freely along with the rudder. When the automatic pilot is in use a solenoid valve on the actuator closes and locks the cylinder. Steering signals from the pilot are now fed to the D.C. motor, which drives the pump to move the cylinder back and forth. De-energized, the solenoid valve immediately disconnects the automatic pilot from the rudder. The actuator has a small translucent oil reservoir, making it easy to check fluid levels. These actuators have only five moving parts. Mechanical simplicity gives our product reliability and ease of service when compared to complicated gear and screw actuators, making our units a favorite for offshore mariners. These actuators are shipped from our factory completely filled with oil and require no additional plumbing. Features Average Current 4-6 amps Max Current 19amps 12vDC Cylinder Bore: 38mm Variable Flow Rate: 600cc-1.2 litre/min Stroke: 305mm/12in Hardover Time(Suggested): 14-16 sec Max Rudder Torque: 1,200Nm/10,600lbin Peak Thrust: 400Kg/882lbs Max boat Length: 18m/60'

Reversing Pump 1200CC/min - 12V - Up to 22ci Cylinder Adjustable displacement Reversing Pump with Bypass Valve & Reservoir 

Linear Actuators OCTAF1012LAM7 An Octopus Hydraulic Linear Actuator is a simple, effective way to drive the rudder on a boat equipped with a mechanical steering system. The linear actuator is an assembly of an Octopus reversing pump and a marine hydraulic cylinder. This assembly is mounted on the rudder tiller-arm or quadrant. When the autopilot is not in use the cylinder runs freely along with the rudder. When the automatic pilot is in use a solenoid valve on the actuator closes and locks the cylinder. Steering signals from the pilot are now fed to the D.C. motor, which drives the pump to move the cylinder back and forth. De-energized, the solenoid valve immediately disconnects the automatic pilot from the rudder. The actuator has a small translucent oil reservoir, making it easy to check fluid levels. These actuators have only five moving parts. Mechanical simplicity gives our product reliability and ease of service when compared to complicated gear and screw actuators, making our units a favorite for offshore mariners. These actuators are shipped from our factory completely filled with oil and require no additional plumbing. Features Average Current 4-6 amps Max Current 19amps 12vDC Cylinder Bore: 38mm Variable Flow Rate: 500cc - 1 litre/min Stroke: 178mm/7in Hardover Time(Suggested): 12-14 sec Max Rudder Torque: 750Nm/6,630lbin Peak Thrust: 400Kg/882lbs Max boat Length: 14m/45'

Linear Actuators OCTAF1012LAR7 An Octopus Hydraulic Linear Actuator is a simple, effective way to drive the rudder on a boat equipped with a mechanical steering system. The linear actuator is an assembly of an Octopus reversing pump and a marine hydraulic cylinder. This assembly is mounted on the rudder tiller-arm or quadrant. When the autopilot is not in use the cylinder runs freely along with the rudder. When the automatic pilot is in use a solenoid valve on the actuator closes and locks the cylinder. Steering signals from the pilot are now fed to the D.C. motor, which drives the pump to move the cylinder back and forth. De-energized, the solenoid valve immediately disconnects the automatic pilot from the rudder. The actuator has a small translucent oil reservoir, making it easy to check fluid levels. These actuators have only five moving parts. Mechanical simplicity gives our product reliability and ease of service when compared to complicated gear and screw actuators, making our units a favorite for offshore mariners. These actuators are shipped from our factory completely filled with oil and require no additional plumbing. Features Average Current 4-6 amps Max Current 19amps 12vDC Cylinder Bore: 38mm Variable Flow Rate: 500cc - 1 litre/min Stroke: 178mm/7in Hardover Time(Suggested): 12-14 sec Max Rudder Torque: 750Nm/6,630lbin Peak Thrust: 400Kg/882lbs Max boat Length: 14m/45'

  Purchase an HDS LIVE or all-new HDS PRO and get up to $800 maximum savings on qualifying fishing system components including ActiveTarget Live sonar ($200), Ghost Trolling Motor ($500), MotorGuide Xi5 ($200) or Tour Pro ($200) Trolling Motors, HALO Radar ($400) and NAC-2 or NAC-3 autopilots ($300).   Offer valid now until April 30th, 2023     HDS PRO With built-in support for the new, ultra-high-definition Active Imaging™ HD and ActiveTarget® 2 you’ll see more clearly and find more fish than ever before.   HDS LIVE Premium performance and support for the best collection of innovative sonar and navigation features available.   Ultimate Fishing System Components Seamlessly combine core fishing products on your boat to create one Ultimate Fishing System.   Offer valid now until April 30th, 2023     Specials    Closeouts    Remanufactured    Rebates

Sherwood R-30-G-1 WESTERBEKE PUMP For Westerbeke 6 Cylinder Diesel 24102 Pump Body: Bronze Ports: 1/2" NPT Cam: Full Impeller: Neoprene Shaft Seal: Mechanical Drive: Pulley Driven Pedestal Pump

  Receive up to $300 back when you purchase a qualifying GO XSE or XSR. Cruise with confidence and fish like a pro. Behind every sunlight-viewable touchscreen lies a built-in GPS receiver, echosounder, wireless connectivity, and industry-standard NMEA 2000® networking.   Offer valid now until April 30th, 2021     Choose Your GO Display or Bundle Don't miss out now until April 30th, 2021, on the Simrad GO Promotion. Receive up to $300 back when you buy a qualifying Simrad GO XSE and XSR Chartplotters.     Simrad GO series displays are designed to help you make the most of your time on the water and are a perfect addition to sportboats, dayboats, and center-consoles. Behind every sunlight-viewable GO series touchscreen lies a built-in GPS receiver, echosounder, wireless connectivity, and industry standard NMEA 2000® networking. Navigate, connect with mobile devices, control accessories like your on-board sound system, and choose from an array of built-in sonar. Radar capability—available on the GO7 and above—offers added safety and fishfinding functionality.   Specials    Closeouts    Remanufactured    Rebates  

  Receive up to $200 back when you purchase select B&G Vulcan Chartplotters. Purchase a qualifying model now until April 30th, 2021. Don't miss out on these super savings! Offer valid now until April 30th, 2021     B&G's Vulcan range of sailing chartplotters take the guesswork out of sailing. Whether you’re an experienced sailor or just starting out, Vulcan is packed with features that will help you get the most from your time on the water.   *Offer valid now until April 30th, 2021     Specials    Closeouts    Remanufactured    Rebates  

    Furuno BBWX4 - Save Up To $200 in Rebates! Purchase a new Furuno BBWX4 SiriusXM Satellite Weather & Radio Receiver now until March 31st, 2021, to qualify for a $100 rebate from Furuno. On top of that, SiriusXM is offering an additional $100 VISA Gift Card for activating your device with a qualifying plan*. That’s up to $200 in rebates!   For serious anglers looking for that competitive edge, the BBWX4 will soon offer extremely detailed “Fish Mapping” functionality on select NavNet TZtouch displays, providing you with a big advantage you’ll love having on tournament day!       Specials    Closeouts    Remanufactured    Rebates

Groco 12V-F 12V Motor 1/8Hp 3.5" Shaft  

Groco GPBR-1-12V Reversable Gear Pump for Oil Changes Groco Gear Pump Bronze 3.0GPM 50psi Max 24VDC Reversible 3/8”NPT Ports