|
160A Automatic Charge Isolator - 12V or 24V
The ACR-160 combines battery banks for charging and isolates them when charging has stopped. It provides priority for charging only the starter battery first and protects from excessive discharging of the starter battery.
The Automatic Charge Isolator is also referred to as a battery separator, battery isolator or an automatic charging relay.
Features:
Microprocessor controlled, dual sensing
Easy to install - does not require charging the existing circuit of the alternator
Potted, waterproof, sealed unit
Low standby current
Automatic detection of 12 or 24 VDC systems
160 Amp continuous rated, 480 Amp peak (250 msec)
Monitoring of relay activation by external LED
Over voltage protection
Specifications:
Input: 12/24 VDC
Output: 12/24 VDC
Amps: 160
Warranty: 2 Year Limited
Applications:
Marine
Automotive
Recreational
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
127.37 |
|
|
Battery Monitor - 12V or 24V - Programmable
The Battery Monitor is a smart piece of equipment which automatically detects battery voltages between 7V and 32V; ideal for 12/24 volt systems.
BW-01 Battery Monitor - intelligent 12V/24V programmable system.
Features:
3 LED: green, red and yellow to display various combinations to indicate battery voltage
audio alarm that sound at high or low voltage level
all settings are programmable by user
Specifications:
Input: 12V/24V
Output: 12V/24V
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
47.87 |
|
|
Dual Battery Monitor - 12V or 24V - Auto Detection
Features:
Multiple battery monitoring using advanced micro-controller
Auto 12V/24V detection
Digital display
Programmable alarm thresholds
Very low power consumption/Power Saving Mode
Splash resistant top
Easy to install/shallow mounting depth
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
86.59 |
|
|
20A Solar Charge Controller - 12/24V
The MSK-20A is a 3-stage intelligent series-type PWM charge controller. It is based on an advanced design using a microcontroller for digital accuracy and fully automatic operation. It can be used for 12V or 24V battery systems.
Features:
3-stage intelligent Series Type PWM charging
Automatic battery voltage detection: 12V / 24V
100% input and output within -35 degrees C to +50 degrees C
Electronic protections: overheating, overcharging, over-discharge, overload, and short circuit
Reverse protection: any combination of solar module and battery
Optional MSK-TS External Temperature Sensor
Applications:
Recreational and service vehicles
Off-grid grid
Portable charging kits
Boats and marine crafts
Fieldwork or mobile offices
Telecommunications
Specifications:
Input: 12V / 24V
Amps: 20 amps
Weight: 0.66 (lbs)
Weight: 0.3 (kgs)
Dimensions: 6.28 x 3.2 x 1.89 in.
Dimensions: 159.6 x 81.4 x 47.88 (mm)
|
70.91 |
|
|
Take the hard work out of your sailing time with ANDERSEN's Electric Winches. They allow you to raise the sails or trim the sheets with the push of a button. If you enjoy short-handed sailing or have a large, hard-to-control mainsail or genoa, electric winches are a great choice. Easily user installed and maintained, Andersen electric winches can be installed in the same position as your current winches.
E1 Electric Self-Tailing Winches
Perfect for enjoying sailing short-handed or with friends and family. ANDERSEN E1 Electric Winches are engineered with unsurpassed levels of functionality, monitoring and protection. They are available in 12 Volt and 24 Volt models providing smooth and quiet operation across a wide working load range.
Compact Motor™ Electric Winches - Above Deck & Below Deck – Variable Speed
The ANDERSEN Compact Motor™ electric winch is available in two formats for either Above Deck or Below Deck motor placement. Motor gearbox and controller are integrated into one compact unit with no extra control box necessary. Available in 12 volt and 24 volt models, Compact Motor™ electric winches operate at variable speed in proportion to the pressure applied to the push button, for smooth and quiet operation.
Electric Power Unit Upgrade
ANDERSEN winches are engineered with a focus on flexibility and simplicity. Already have an existing Andersen Self-Tailing Manual Winch? Purchase a conversion kit and turn it into an Electric winch with ease, since all ANDERSEN Self-Tailing Winches, models 28ST and above are factory prepared for future change.
E1 Single Speed Electric Conversion Kits
The E1 Single Speed electric motor is a high quality European engineered and manufactured series wound motor. Carefully matched with the optimal gearbox they deliver high speed at low load for fast sheeting in, and low speed at high load for safe, fine tuning when trimming. The motors are available in 12 Volt and 24 Volt models providing smooth and quiet operation across a wide working load range.
Compact Motor™ Electric Conversion Kits
The uncompromising ANDERSEN Variable-speed Compact Motor™ is available in two versions; Below Deck and Above Deck, 12V or 24V, and will fit models 28ST and up. The unit is extremely easy to install and provides 30-50% less power consumption compared to a conventional electric motor.
Specials Closeouts Remanufactured Rebates
|
|
|
Automatic Charging Relay Plus - 160A - 24V
This 160A Egis automatic charging relay eliminates dead-start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present.
Applications:
Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance
Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell
Features:
Ultra-low power draw compared to typical ACRs (7-10 mA) vs. the 7610 ACR @ 1.3 mA will not deplete batteries even after extended electrical system downtime.
Simple and robust installation - integrated sealed plug eliminates corrosion; includes Deutsch/Amphenol DTM connector harness
Start to assist input option to ensure maximum cranking amps are available by allowing manually connecting batteries via a remote switch
Bullet-proof construction - sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere; Integrated thermal overload shutdown protection
Additional low-amp output can be used to report device status remotely or drive a secondary relay for charge to a battery bank without a charge source (see examples)
Specifications:
Continuous Current Amps: 160
Voltage Range (VDC): 16 – 36
Off-State Current Draw (mA): 1.3
Interrupt Current (Amps): 240
AC Closing Voltage Range (VDC): 25.8-27.2
AC Opening Voltage Range (VDC): 24.2-25.6
Focal Features:
Top Side Dip Switches
Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover.
Stainless Steel Self-Locking Hardware
100% non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking.
Integral I/O Connector
Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products.
Connection Options
Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads).
Easy Integration with RT Fuse Blocks (24 HR Circuits)
Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series fuse blocks.
LED Diagnostics
Indicates pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.
|
105.44 |
|
|
Programmable Automatic Charging Relay (ACR) 160A, 12V
This 160A Egis charging relay is automatic and programable. The relay eliminates dead start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present.
Applications:
Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance.
Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell.
Features:
Ultra-Low Power Draw Compared to typical ACRs (7-10 mA) vs 7610 ACR @ 1.3 mA, will not deplete batteries even after extended electrical system downtime.
Simple and robust installation - The integrated sealed plug eliminates corrosion and includes a Deutsch/Amphenol DTM connector harness
Start Assist input option to ensure maximum cranking amps are available by allowing the manual connection of batteries via a remote switch.
Bullet-proof construction - Sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere. Integrated thermal overload shutdown protection.
Additional low-amp output can be used to report device status remotely or drive a secondary relay for charging a battery bank without a charge source (see example)
Specifications:
Continuous Current (Amps): 160
Voltage Range: 8-18 VDC
Off-State Current Draw mA: 1.3
Interrupt Current (Amps): 240
ACR Closing Voltage (VDC): 12.9-13.6
ACR Opening Voltage (VDC): 12.1-12.8
Focal Features:
Top Side Dip Switches
Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover.
Stainless Steel Self-Locking Hardware
100% Non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking.
Integral I/O Connector
Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products.
Connection Options
Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads).
Easy Integration with RT Fuse Blocks (24 HR Circuits)
Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series Fuse Blocks.
LED Diagnostics
Provides an indication of pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.
|
104.96 |
|
|
10A Solar Charge Contoller - 12/24V
Features:
Advanced micro-controller with Series Type PWM Charging
10A charging for 12V / 24V Lead Acid, Sealed AGM Batteries with auto mbattery voltage detection
10A rated load terminals with protection for low battery disconnect
Integrated battery voltage temperature compensation to prevent under/over charging
User friendly LED display for monitoring
Suitable for up to 160W panels for 12V battery / up to 320W panels for 24V battery
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
43.63 |
|
|
PowerCombi Pure Sine Wave Inverter/Charger - 1200W - 12V - 50A Kit
Simple. Independent. Flexible.
The PowerCombi is a pure sine wave inverter/charger offering grid quality AC power and battery charging in one low profile design. Designed to be an independent inverter/charger, it yet can easily be integrated into a MasterBus network (with additional interface).
With a built-in transfer switch, 2x surge for 3 seconds and on-site dipswitch programming—the PowerCombi offers simple installation with multiple operating modes, and can charge various battery chemistries—including a custom profile for use with Li-ion.
Full certifications make it perfect for use in RV's, boats, and specialty vehicles. Add a battery temperature sensor (BTS), remote display and a communication interface for custom applications.
Features:
Input voltage range: 10-15.5V DC
Includes temperature sensor and powercombi remote
Can be used with Flooded, Gel, AGM and custom battery types
MasterBus compatible via CZone - MasterBus Interface
|
986.40 |
|
|
Portable Solar Charging Kit - 90W
Samlex Portable MSK Charging Kits are easy to use! Just unfold, plug in and start charging. Capture the power of the sun without complicated installations, brackets or electrical diagrams. Each Kit comes with a convenient insulated carrying case that also protects the panels when stored.
Your Kit Includes:
3 x 30W Solar Modules for charging 12V Lead Acid Batteries
10 Amp Charge Controller
Includes a 2-pin bullet adapter for use in solar ready RV's
Protective carrying case
(Battery Not Included)
Features:
Solar panel is pre-wired with battery clamps for a quick and easy connection, 16’ cable
Turn the panel a few times per day and increase charging by 30%
Adjustable legs allow for maximum sun exposure
Folding crystalline panels in anodized aluminum frames, won’t rust
Built-in 10 Amp Charge Controller manages the charge to the battery and prevents overcharging
For 12V Lead Acid Batteries
Includes protective carrying case
NOTE: Battery is not included
Specifications:
Watts: 90 Watt Solar Module for 12V Lead Acid Batteries
Amps: 10 Amps
Weight: 25.2 (lbs)
Weight: 11.45 (kg)
Dimensions: 40.75 x 25.39 x 1.18 (in) Open
Dimensions: 1035 x 645 x 30 (mm) Open
Warranty: 10 Year Power Warranty on Solar Panels (Canada/US)
Applications:
Recreational Vehicles
Off-grid/mobile solar systems
Power supply for remote equipment
Water pumping systems
Rural electrification
Small home power systems
12V Lead Acid battery charging system
Other industrial and consumer applications
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
402.28 |
|
|
Portable Solar Charging Kit - 135W
Samlex Portable MSK Charging Kits are easy to use! Just unfold, plug in and start charging. Capture the power of the sun without complicated installations, brackets or electrical diagrams. Each Kit comes with a convenient insulated carrying case that also protects the panels when stored.
Your Kit Includes:
3 x 45W Solar Modules for charging 12V Lead Acid Batteries
10 Amp Charge Controller
Includes a 2-pin bullet adapter for use in solar ready RV's
Protective carrying case
(Battery Not Included)
Features:
Solar panel is pre-wired with battery clamps for a quick and easy connection, 16’ cable
Turn the panel a few times per day and increase charging by 30%
Adjustable legs allow for maximum sun exposure
Folding crystalline panels in anodized aluminum frames, won’t rust
Built-in 10 Amp Charge Controller manages the charge to the battery and prevents overcharging
For 12V Lead Acid Batteries
Includes protective carrying case
NOTE: Battery is not included
Specifications:
Watts: 135 Watt Solar Module for 12V Lead Acid Batteries
Amps: 10 Amps
Weight: 35.6 (lbs)
Weight: 16.18 (kg)
Dimensions: 59.65 x 24.41 x 1.18 (in) Open
Dimensions: 1515 x 620 x 30 (mm) Open
Warranty: 10 Year Power Warranty on Solar Panels (Canada/US)
Applications:
Recreational Vehicles
Off-grid/mobile solar systems
Power supply for remote equipment
Water pumping systems
Rural electrification
Small home power systems
12V Lead Acid battery charging system
Other industrial and consumer applications
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
473.69 |
|
|
Solar Charge Controller - 12V - 8A
The SCC-1208L Charge Controller is Micro-controller based for automatic, intelligent operation designed for 12 V nominal solar panels and 12 V battery systems. It has 3 Stage charging (Bulk, Absorption, Float) for 100% return of capacity and long battery life. It can be used with 2 types of batteries: Flooded/Web Cell or Sealed AGM. The SCC-1208L can manage up to 150 Watts of Solar Power.
Features:
Micro-controller based for automatic, intelligent operation
Designed for 12V nominal solar panels and 12V battery systems
3 Stage charging (Bulk, Absorption, Float) for 100% return of capacity and long battery life
For use with 2 types of batteries: Flooded/Wet Cell or Sealed AGM
Totally sealed, splash proof weather resistant design (Ingress Protection Rating IP65)
Automatically turns on lights when dark and turns off during the day
Mosfet based reverse current blocking prevents night-time battery discharge and lowers power loss
Protections: Overload, Over-Temperature, Battery Under/Over Voltage, Reverse Polarity
Wide operating temperature range of -40°C to + 60°C
Specifications:
Input: 12V
Amps: 8 Amps
Weight: 0.28 (lbs) / 0.13 (kg)
Dimensions: 3.8 x 1.8 x 1.0 (in)
Dimensions: 9.65 x 4.57 x 2.54 (cm)
Safety: FCC, CE, IP65
Warranty: 5 Year Limited
Applications:
Off-grid mobile rural systems
Rural electrification
Power supply for remote equipment
Monitoring systems for the oil & gas industry
Traffic, security, environment, and other remote monitoring and signaling systems
Water pumping systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
49.91 |
|
|
ROKK Charge Pro Fast Charge USB-A & USB-C Socket
ROKK Charge Pro is the ultimate onboard USB charger. Featuring a USB-A and USB-C charging port housed in an IPX6 waterproof design, this is the only USB-C charger on the market that remains waterproof while in use.
Say hello to fast charging! The unique design charges up to 36W on 12V systems and 60W on 24V systems. This makes it ideal for charging modern laptops via the USB-C port. It's also twice as fast when charging larger tablets, designed to easily charge an iPad Pro and iPhone at the same time.
Perfect for where space is at a premium, ROKK Charge Pro has a sleek, ultra-compact design with a click-and-lock lid allowing the USB to remain waterproof while in use. Constructed from premium, marine-grade materials, ROKK Charge Pro is IPX6 waterproof making it completely wash-down ready.
USB – C output:
60W max on 24V system
36W max on 12V system
USB – A output:
36W max
The install cut-out matches those of standard USB sockets for easy retrofit or swap of an existing USB charger, allowing you to keep up with the heavier power draws of modern electronic devices.
Universal:
Universal fit for any USB-A or USB-C connectors
Fast charge (60W max) up to 2 devices at a time.
Easy Install, using standard USB mounting hole - 29mm (1 1/8”)
Washdown Proof:
IPX6 waterproof with the lid closed
Marine Ready:
Anti-corrosion coating on the circuit board
UV resistant
316 stainless hinge and spring
Electrical Information:
Input voltage: 10-30V DC (12/24V System)
Input current Max: 6A (10A fuse recommended)
Standby power draw: 0.01W
The charge cable supplied with your device (tablet, phone, action camera, etc) must be used to achieve maximum charge performance from this charger. Phones will charge at the same speed whether on a 12V or 24V input voltage system. However, a 24V system must be used to get the full 60W output suitable for fast-charging laptops.
|
41.82 |
|
|
135Amp 12/24V Windlass Isolator
Maxwell circuit breaker/isolator panel, 135 Amp 12/24-volt, suitable for all 800 to 3500 Series 12V & 4000 24V windlasses.
Features:
For protection of the main conductor circuit for DC winches and the control circuit for hydraulic winches
Mount as close as possible to the battery power source to ensure protection against short circuit and to reduce the risk of DC motor burn-out in the event of winch overloading
Enables the battery, or electrical supply, to be isolated when winch is not in use
Suitable for 12V or 24V DC systems
|
130.44 |
|
|
Evolution™ F Series 1200W, 120V Pure Sine Wave Inverter/Charger with 12V Input & 40 Amp Charger
Pure sine wave inverter/charger with 6 programmable charging profiles – 2, 3 and 4 stages with Equalization. For use with Lead Acid or Lithium Batteries. Samlex Evolution™ Series inverter/chargers provide reliable AC power wherever it’s needed. For use with boats, RVs, cabins and specialty vehicles, as well as alternative energy, back-up and emergency power applications.
Adaptive Battery Charger Option for Lead Acid Batteries
6 programmable charging profiles – 2, 3 and 4 stages with Equalization
Algorithm monitoring in the Bulk Stage assesses the battery’s condition. The remaining charging stages are based on the battery’s condition rather than a pre-set charging time.
Reduces excess charging time and extends life of battery
Transfer Switch
Zero transfer time when switching from Inverter to AC input source. When AC input source comes on, the inverter synchronizes with the incoming wave form and then transfers instantly at zero crossing without interruption to the load.
Surge Capacity (Active Power Boost)
The inverter has a surge capability of 3X its continuous power rating, allowing it to turn on loads with high starting surge.
Inverter loads can exceed the continuous power output by the Power Boost Allowances without triggering and overload fault.
There is no need to upsize to a larger inverter/charger to handle a heavy surge load, resulting in reduced costs.
Solar Input
Connect a solar charge controller (up to 50A) directly to the EVOTM though the Battery Charger External DC Input
External charging current is monitored to free up more power from the grid to be available to the load while charging.
ONLINE Mode can be used to prioritize Batteries/Inverter over the grid, ideal for those who want to operate primarily on solar power, even when the grid is available (when grid is costly).
State-of-the-Art Technology
Multiple physical points of protection monitoring are scanned up to 10,000 times per second to detect adverse internal and external conditions.
The EVO™ is practically indestructible. The EVO™ will detect fault conditions and initiate a healthy shutdown before any damage can be done.
AC Input / Output Option
AC Power Cord Inlet and Duplex GFCI outlet: EVO-1212F/1224F; hardwired: EVO-1212F-HW/1224F-HW
The EVO-RC-PLUS remote control (sold separately) can be used to capture detailed EVOTM performance data, stored on a removable 16GB SD Card. Advanced features for programming various parameters and modes of operation. 4 rows of 20 character alpha numeric LCD display for messaging.
The EVO™ uses five temperature sensors placed throughout the unit to determine operation of 2 speed controlled cooling fans. Reduces unnecessary fan noise and energy consumption by only running when and where the fans are needed.
Applications:
Boats, RVs, trucks, specialty vehicles
Alternative energy, off-grid, cabins, remote locations, areas with unreliable utility power
Back-up and emergency power applications
ABYC Compliant
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
837.54 |
|