Automatic Charging Relay Plus - 160A - 24V This 160A Egis automatic charging relay eliminates dead-start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications:  Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell Features: Ultra-low power draw compared to typical ACRs (7-10 mA) vs. the 7610 ACR @ 1.3 mA will not deplete batteries even after extended electrical system downtime. Simple and robust installation - integrated sealed plug eliminates corrosion; includes Deutsch/Amphenol DTM connector harness Start to assist input option to ensure maximum cranking amps are available by allowing manually connecting batteries via a remote switch Bullet-proof construction - sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere; Integrated thermal overload shutdown protection Additional low-amp output can be used to report device status remotely or drive a secondary relay for charge to a battery bank without a charge source (see examples) Specifications: Continuous Current Amps: 160 Voltage Range (VDC): 16 – 36 Off-State Current Draw (mA): 1.3 Interrupt Current (Amps): 240 AC Closing Voltage Range (VDC): 25.8-27.2 AC Opening Voltage Range (VDC): 24.2-25.6 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads).  Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series fuse blocks.  LED Diagnostics Indicates pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

Programmable Automatic Charging Relay (ACR) 160A, 12V This 160A Egis charging relay is automatic and programable. The relay eliminates dead start batteries by sharing charging on either of two batteries and isolating batteries when no charge sources are present. Applications: Supports multiple engines or independent charge systems by incorporating two independent start or engine isolation inputs to allow isolation of charge sources when both are active to maximize charging performance. Protects Electrical System Cascading Faults with an optional lock-out from closing if one terminal is connected to a battery with a shorted cell. Features: Ultra-Low Power Draw Compared to typical ACRs (7-10 mA) vs 7610 ACR @ 1.3 mA, will not deplete batteries even after extended electrical system downtime. Simple and robust installation - The integrated sealed plug eliminates corrosion and includes a Deutsch/Amphenol DTM connector harness Start Assist input option to ensure maximum cranking amps are available by allowing the manual connection of batteries via a remote switch. Bullet-proof construction - Sealed unit, stainless steel hardware, and high-temperature materials allow mounting anywhere. Integrated thermal overload shutdown protection. Additional low-amp output can be used to report device status remotely or drive a secondary relay for charging a battery bank without a charge source (see example) Specifications: Continuous Current (Amps): 160 Voltage Range: 8-18 VDC Off-State Current Draw mA: 1.3 Interrupt Current (Amps): 240 ACR Closing Voltage (VDC): 12.9-13.6 ACR Opening Voltage (VDC): 12.1-12.8 Focal Features: Top Side Dip Switches Accessible after mounting for programming voltage settings and determining active features. Protected by self-retained cover. Stainless Steel Self-Locking Hardware 100% Non-ferrous corrosion-resistant materials. All attachment screws and nuts are self-locking. Integral I/O Connector Sealed Molex MX-150 connector eliminates the susceptibility to corrosion and vibrating loose of 1/4" quick connect terminals on competitive products. Connection Options Comes standard with a Deutsch DT/AT style connector harness. Provides three connection options (MX-150, DT/AT, and wire leads). Easy Integration with RT Fuse Blocks (24 HR Circuits) Optional EasyLink bus bars reduce the space and cost of connecting TH Series relays with RT Series Fuse Blocks. LED Diagnostics Provides an indication of pending relay ON/OFF, under voltage, over voltage/temp, start isolation/assist, and output on/off status.

160A Automatic Charge Isolator - 12V or 24V The ACR-160 combines battery banks for charging and isolates them when charging has stopped. It provides priority for charging only the starter battery first and protects from excessive discharging of the starter battery. The Automatic Charge Isolator is also referred to as a battery separator, battery isolator or an automatic charging relay. Features: Microprocessor controlled, dual sensing Easy to install - does not require charging the existing circuit of the alternator Potted, waterproof, sealed unit Low standby current Automatic detection of 12 or 24 VDC systems 160 Amp continuous rated, 480 Amp peak (250 msec) Monitoring of relay activation by external LED Over voltage protection Specifications: Input: 12/24 VDC Output: 12/24 VDC Amps: 160 Warranty: 2 Year Limited Applications: Marine Automotive Recreational WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7601 DC Mini ACR Automatic Charging Relay - 65 Amp Features: 65 Amp continuous rating manages the charging current from alternators up to 65 Amps found on most outboards and many inboard engines Compact case design allows surface and panel mounting Senses charging on two battery banks Snap-on cover insulates terminal connections LED indicates ACR status 1/4" x .032" male quick connect terminal for ground 5/8" (16 mm) stud length to accept multiple cable terminals 12V DC voltage input Specifications: Intermittent Rating: 5 min.: 115A Terminal Stud Size: 1/4"-20 Relay Contact Position: Open (30 sec.): 12.75V DC Continuous Rating: 65A Maximum Torque: 75 in-lb (8.5 Nm) Relay Contact Position - Open High: 16.0V DC Amperage Operating Current: 175mA (Combine) Relay Contact Position: Combine (30 sec.): 13.0V DC Under Voltage Lockout: 9.5V DC Amperage Operating Current: 15mA (Open) Relay Contact Position: Combine (2 min.): 13.6V DC Maximum Cable Size: 1/0 AWG Relay Contact Position: Open (10 sec.): 12.35V DC WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7610 120 Amp SI-Series Automatic Charging Relay Allows temporary isolation of house loads from engine circuit during engine cranking to protect sensitive electronics Automatically combines battery banks during the charging cycle and isolates under discharge 12/24 Volt auto ranging voltage input Waterproof rated IP67 - temporary immersion for 30 minutes Ignition protected - safe for installation aboard gasoline powered boats Remote LED output indicates relay state away from ACR LED light indicates when batteries are combined LED blinks in undervoltage lockout and starting lockout Supports high-output alternators up to 120 Amperes Included with the ADD A BATTERY Dual Circuit System Automatically combines battery banks during the charging cycle and isolates under discharge Ignition protected - safe for installation aboard gasoline-powered boats Activates from any charging source - alternators, battery chargers, or solar panels Hermetically sealed contacts / vaporproof Side and bottom knockouts for power cable connections Clip-on cover protects and insulates terminal connections Tin-plated copper studs for maximum corrosion resistance 7/8" (22.22mm) stud length to accept multiple cable terminals 1/4" x 0.031" male quick connect terminals for ground and remote LED and starting interrupt WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7611 DC BatteryLink™ Automatic Charging Relay - 120 Amp w/Auxiliary Battery Charging Features: 120 Amp continuous rating 12/24V DC auto ranging voltage input Senses charging on two battery banks Side and bottom knockouts for cable connections Clip-on cover insulates terminal connections 7/8" (22 mm) stud length to accept multiple cable terminals Integrated LED indicates ACR status 1/4" x .032" male quick connect terminals for ground and optional features Specifications: Intermittent Rating: 5 min.: 210 Amps Continuous Rating: 120 Amps Nominal Voltage: 12/24 Volts DC WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7621 Manual Control: No Coil Voltage: 24V DC Combines battery banks during charging and isolates under discharge 500 Ampere continuous rating suitable for use with large battery banks, starters, alternators, and inverter/chargers Can be remotely combined with optional switch Silver alloy contacts provide high reliability 3/8" copper studs, using Blue Sea Systems superior one piece stud technology, suitable for 300 Ampere continuous rating and large cable connections WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XD Series Triple Flex 2 Relay-ACR-Relay with Knobs & Tinned Wires The Egis relay replaces three individual high-amp relays with one compact module, reducing space significantly, eliminating the cost of external link cable connections, eliminating the risk of link cable connections vibrating loose, and providing clear, unambiguous awareness of how to operate manual controls and what state the manual controls have forced the relay into. Applications:  Designed to replicate common multi-battery switching and charge management functions - common dual battery load switching via the outer relays and a central automatic charging relay to share charge current are easily implemented Multiple automatic charging relays (ACR) into one device - for 3-4 battery systems that require 2 or 3 ACRs, a single three-relay ACR provides drastic improvements in off-state quiescent current draw, space used, and reduces unnecessary interconnection cables.  Expandable with link and cross-link busbars to additional dual, triple, or single XD relays - supports 3 or 4 battery systems with standard busbar interconnect accessories. Features: Bullet-proof construction - sealed to IP67/IP6K9K, high temperature electronics and materials allow mounting anywhere; stainless steel cable lug studs; large mounting holes accept 1/4-20 / M6 attachment hardware Intuitive manual control option simplifies operation and increases awareness of the state of the manual override and whether the device is being left in a locked-off or locked-on state (not available on competitive solutions) Simple programming via simple dip switches allows each relay function significant flexibility for OEMs and installers. 35-75% reduction in mounting space and product weight via advanced bi-stable solenoid design and multiple solenoid assemblies that replace common electrical system layouts Plug and play compatible with legacy competitor products - single, dual, and triple relay options are available with DTM/ATM connector pins compatible with ML Series bi-stable relays 90-95% less off-state current compared to competitive products and system solutions that require multiple devices for similar functionality Specifications: Total Continuous Current Amps: 500 Max Cranking Current (Amps): 1500 Mechanical Switching Life: 1,000,000 Cycles Voltage Range (VDC): 8-36 Off-State Current Draw (mA): 1.3 State Change Current: 5A @ 12 VDC; 3A @ 24 VDC Focal Features: Led Status Display The easy-to-see front-facing LED indicator provides visual device status, and the remote LED replicates the local on-device LED.  3-Position Manual override Force each relay open or closed, and optionally leave the knob in either position to lock the relay in either condition.  40 Circuit Label Sheet Included Convenient recesses for the included weatherproof label set make circuit and relay identification easy. Blank labels for custom applications.  Protective Cover included Protects terminal studs and cable terminal edges from inadvertent shorts to each other or ground.  Stainless Hardware  Corrosion is no issue with quality stainless steel studs and self-locking flanged nuts. Programmable Via dip switches located under the protective cover. An easy-to-use configuration guide on the reverse makes custom settings a breeze to configure for a wide variety of applications.  Smaller Footprint XD relays offer a high amp rating in a smaller package than competitive solutions, reducing installation space requirements to a minimum.  Integrated Vent High-quality Gortex vents regulate internal device pressure to eliminate moisture entry across seals and ensure long product life in harsh environments.

XD Series Triple Flex 2 Relay-ACR-Relay with Knobs & 3X DTM Connector The Egis relay replaces three individual high-amp relays with one compact module, reducing space significantly, eliminating the cost of external link cable connections, eliminating the risk of link cable connections vibrating loose, and providing clear, unambiguous awareness of how to operate manual controls and what state the manual controls have forced the relay into. Applications:  Designed to replicate common multi-battery switching and charge management functions - common dual battery load switching via the outer relays and a central automatic charging relay to share charge current are easily implemented Multiple automatic charging relays (ACR) into one device - for 3-4 battery systems that require 2 or 3 ACRs, a single three-relay ACR provides drastic improvements in off-state quiescent current draw, space used, and reduces unnecessary interconnection cables Expandable with link and cross-link busbars to additional dual, triple, or single XD relays - supports 3 or 4 battery systems with standard busbar interconnect accessories Features: Bullet-proof construction - sealed to IP67/IP6K9K, high temperature electronics and materials allow mounting anywhere; stainless steel cable lug studs; large mounting holes accept 1/4-20 / M6 attachment hardware Intuitive manual control option simplifies operation and increases awareness of the state of the manual override and whether the device is being left in a locked-off or locked-on state (not available on competitive solutions) Simple programming via dip switches gives each relay function significant flexibility for OEMs and installers. 35-75% reduction in mounting space and product weight via advanced bi-stable solenoid design and multiple solenoid assemblies that replace common electrical system layouts Plug and play compatible with legacy competitor products - single, dual, and triple relay options are available with DTM/ATM connector pins compatible with ML Series bi-stable relays (This relay has 3x DTM connectors) 90-95% less off-state current compared to competitive products and system solutions that require multiple devices for similar functionality Specifications: Total Continuous Current Amps: 500 Max Cranking Current (Amps): 1500 Mechanical Switching Life: 1,000,000 Cycles Voltage Range (VDC): 8-36 Off-State Current Draw (mA): 1.3 State Change Current: 5A @ 12 VDC; 3A @ 24 VDC Focal Features: Led Status Display The easy-to-see front-facing LED indicator provides visual device status, and the remote LED replicates the local on-device LED.  3-Position Manual override Force each relay open or closed, and optionally leave the knob in either position to lock the relay in either condition.  40 Circuit Label Sheet Included Convenient recesses for the included weatherproof label set make circuit and relay identification easy. Blank labels for custom applications.  Protective Cover included Protects terminal studs and cable terminal edges from inadvertent shorts to each other or ground.  Stainless Hardware  Corrosion is no issue with quality stainless steel studs and self-locking flanged nuts. Programmable Via dip switches located under the protective cover. An easy-to-use configuration guide on the reverse makes custom settings a breeze to configure for a wide variety of applications.  Smaller Footprint XD relays offer a high amp rating in a smaller package than competitive solutions, reducing installation space requirements to a minimum.  Integrated Vent High-quality Gortex vents regulate internal device pressure to eliminate moisture entry across seals and ensure long product life in harsh environments.

XD Series Triple Flex 2 Mechanical Switch-ACR-Mechanical Switch with Knobs & DTM Connector The Egis relay replaces three individual high-amp relays with one compact module, reducing space significantly, eliminating the cost of external link cable connections, eliminating the risk of link cable connections vibrating loose, and providing clear, unambiguous awareness of how to operate manual controls and what state the manual controls have forced the relay into. Applications:  Designed to replace common multi-battery mechanical switching and charge management functions - common dual battery load switching via the outer relays and a central automatic charging relay to share charge current are easily implemented Expandable with link and cross-link busbars to additional dual, triple, or single XD relays - supports 3 or 4 battery systems with standard busbar interconnect accessories. Features: Bullet-proof construction - sealed to IP67/IP6K9K, high temperature electronics and materials allow mounting anywhere; stainless steel cable lug studs; large mounting holes accept 1/4-20 / M6 attachment hardware Intuitive manual control option simplifies operation and increases awareness of the state of the manual override and whether the device is being left in a locked-off or locked-on state (not available on competitive solutions) Simple programming via dip switches gives each relay function significant flexibility for OEMs and installers. 35-75% reduction in mounting space and product weight via advanced bi-stable solenoid design and multiple solenoid assemblies that replace common electrical system layouts Plug and play compatible with legacy competitor products - single, dual, and triple relay options are available with DTM/ATM connector pins compatible with ML Series bi-stable relays (This relay has a DTM connector) 90-95% less off-state current compared to competitive products and system solutions that require multiple devices for similar functionality Specifications: Total Continuous Current Amps: 500 Max Cranking Current (Amps): 1500 Mechanical Switching Life: 1,000,000 Cycles Voltage Range (VDC): 8-36 Off-State Current Draw (mA): 1.3 State Change Current: 5A @ 12 VDC; 3A @ 24 VDC Focal Features: Led Status Display The easy-to-see front-facing LED indicator provides visual device status, and the remote LED replicates the local on-device LED.  3-Position Manual override Force each relay open or closed, and optionally leave the knob in either position to lock the relay in either condition.  40 Circuit Label Sheet Included Convenient recesses for the included weatherproof label set make circuit and relay identification easy. Blank labels for custom applications.  Protective Cover included Protects terminal studs and cable terminal edges from inadvertent shorts to each other or ground.  Stainless Hardware  Corrosion is no issue with quality stainless steel studs and self-locking flanged nuts. Programmable Via dip switches located under the protective cover. An easy-to-use configuration guide on the reverse makes custom settings a breeze to configure for a wide variety of applications.  Smaller Footprint XD relays offer a high amp rating in a smaller package than competitive solutions, reducing installation space requirements to a minimum.  Integrated Vent High-quality Gortex vents regulate internal device pressure to eliminate moisture entry across seals and ensure long product life in harsh environments.

Charge Mate Pro 40 - Electronics Charge Relay Current limited electronic charge relay with high efficiency and reverse current protection A secondary battery on board requires a dedicated charging solution. The Charge Mate Pro makes it possible to distribute the charger or alternator current effectively between two battery banks such as a starter and a service battery. The Charge Mate Pro connects both batteries during charging and keeps them isolated when discharging. This significantly reduces the risk of a flat starter battery for example. The Charge Mate Pro offers an additional advantage over mechanical charge relays, by limiting the charge current to the second battery. The primary battery, like a starter battery, is therefore charged with priority. The return current is automatically blocked even when the secondary battery has a higher voltage. An emergency start function is possible by connecting an optional bypass switch to the Charge Master Pro. A marine application example is the connection of a bow thruster battery to a service battery. The Charge Mate Pro ensures that the service battery is always charged with priority. The blocking of the return current from the bow thruster battery guarantees that the bow battery remains charged while the current limiting also prevents power dips of the onboard electrical network. The Charge Mate Pro series consist of a 40 Amp and a 90 Amp version, both suitable for charger or alternator applications. Charge Mate Pro: for controlled charging from a single source. Applications Leisure and professional marine and mobile applications. An effective solution for high power demand on board and/or the need of prioritised or current limited charging. Features Electronic charge coupling with very low voltage drop Makes effective dual charging possible Suitable for all battery types, including Lithium Ion Charge current secondary battery limited to 40 A High system reliability by prioritised charging of the main battery Unidirectional which blocks return current under all circumstances Prevents power dips of the onboard electrical network Suitable for all kinds of chargers and alternators Monitoring with LED status indication IP65 electronics in a corrosion resistant casing with aluminum heat sinks Fast and easy installation General specifications Remote switch functions:  on, off, auto, start assist Monitoring: LED (warnings and status indication) Output current: limited to 40 A Number of battery outlets: 2 Input voltage range: 9-32 V Parallel configuration: yes Battery voltage: automatic 12/24 V detection Dimensions, hxwxd: 157 x 140 x 80 mm / 6.2" x 5.5" x 3.1" Weight: 0.88 kg / 1.9 lb Approvals: CE Technical specifications Connection possibilities: 3 x fast-on connectors (switch, ground and status) o switch: for an optional single pole ON-OFF-ON switch for remote operation o status: for an optional LED indicator Power consumption: switch open: < 1 mA at 12/24 V DC Battery types: all types (Lithium Ion protection via Multi purpose contact, product code 77030500) Switch on voltage: 13.5 V (12 V) / 27 V (24 V) Switch on delay: 5 sec. Switch off voltage: 12.75 V (12 V) / 25.5 V (24 V) Switch off delay: 2.5 sec. Relay: electronically (mosfets with low voltage drop of max 0.2 V) Temperature range (ambient temp.): -40 °C to 60 °C -40 to 140 °F Protection degree: IP65 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Digtal Voltage Sensing Relay (DVSR) - 12/24V The Digital Voltage Sensing Relay (DVSR) allows the charging of a second battery bank from any single charging source. When the voltage on the charged bank rises sufficiently, the DVSR engages allowing the 2nd battery bank to charge. When charging stops and voltage falls, the DVSR automatically isolates the battery banks, ensuring that engine start batteries are kept fully charged. Digital circuitry provides superior reliability and extremely low power consumption. Digital enhancements have introduced remote sensing circuitry that allows an optional connection from the ignition switch to provide the same functionality as single sense VSR and zero power consumption when engine is off. Another benefit is a zero stand by current draw when remote sensing circuit is utilized with a storage mode switch fitted (switch in open position). Features: Safely charge two or more independent battery banks from one charge source such as an alternator or battery charger Charges engine starting batteries before combining auxiliary bank for charging Protects start batteries from becoming flattened by domestic loads Isolates electronics from harmful electrical surges from starter motors Simple to install 3 wire connection leaves alternator wiring intact No volt drop vs diode isolators Ignition protected Surface or panel mountable Replaces previous models 710-125A and 710-125A-DS Multi voltage, auto selects between 12 and 24V DC operation Digital circuits provide very low power consumption and enhanced performance Remote status LED output option WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

7621100 ML ACR Charging Relay 24V 500A with Deutsch Connector 500 Amp magnetic latching (bi-stable) relay automatically combines batteries during charging and isolates batteries when discharging and when starting engine. Features: Automatically manages the charging of two large battery banks Allows paralleling of battery banks for emergency starting 500 Ampere continuous rating to support high-output alternators Magnetic Latch (ML)—ACR draws very low current (<40mA to monitor terminal voltage) in the "ON" or "OFF" states, and draws moderate current for very short time when changing state Dual sensing—senses charge on both battery banks Start Isolation (SI)—can be configured for temporary isolation of House loads from Engine circuit during engine cranking to protect sensitive electronics Engine Isolation (EI)—can be configured for isolation of two engines while both are running to protect engine electronics and maximize alternator output Senses charging on two battery banks LED output to remotely indicate when batteries are combined, isolated, in voltage lockout, or in Start or Engine isolation 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/8" (22mm) stud length accepts multiple cable terminals Silver alloy contacts provide high reliability for switching live loads Label recesses for circuit identification Specifications: Control Circuit Connection: Deutsch DTM Nominal Voltage: 24VDC Manual Control: No Engine Isolation: Yes Mounting: #10 Start Assist: Yes Start Isolation: Yes Amperage Operating Current When Changing State: <7.0A Terminal Stud Torque: 140 in-lb (15.82 Nm) Continuous Rating: 500A Intermittent Rating: 700A (5 min) Cranking Rating 30 Seconds: 1450A DC Cable Size to Meet Ratings: 2x (4/0) Live Current Switching: 300A@12VDC Master Control Switch Capability: No Switching Cycles: 100,000 Terminal Ring Diameter Clearance: 1.18" (29.97 mm) Terminal Stud Length: 1.50" (38.1 mm) Terminal Stud Size: 3/8" - 16 (M10)

7623100 ML ACR Charging Relay 24V 500A with Manual Control & Deutsch Connector 500 Amp magnetic latching (bi-stable) relay automatically combines batteries during charging and isolates batteries when discharging and when starting engine. Features: Manual control switch provides an added level of safety allowing control with or without power, and offering LOCK OFF capability for servicing Automatically manages the charging of two large battery banks Allows paralleling of battery banks for emergency starting 500 Ampere continuous rating to support high-output alternators Magnetic Latch (ML)—ACR draws very low current (<40mA to monitor terminal voltage) in the "ON" or "OFF" states, and draws moderate current for very short time when changing state Dual sensing—senses charge on both battery banks Start Isolation (SI)—can be configured for temporary isolation of House loads from Engine circuit during engine cranking to protect sensitive electronics Engine Isolation (EI)—can be configured for isolation of two engines while both are running to protect engine electronics and maximize alternator output Senses charging on two battery banks LED output to remotely indicate when batteries are combined, isolated, in voltage lockout, or in Start or Engine isolation 3/8"-16 tin-plated copper studs for maximum conductivity and corrosion resistance 7/8" (22mm) stud length accepts multiple cable terminals Silver alloy contacts provide high reliability for switching live loads Label recesses for circuit identification Specifications: Control Circuit Connection: Deutsch DTM Nominal Voltage: 24VDC Manual Control: Yes Engine Isolation: Yes Mounting: #10 Start Assist: Yes Start Isolation: Yes Amperage Operating Current: 13mA Amperage Operating Current When Changing State: <7.0A Terminal Stud Torque: 140 in-lb (15.82 Nm) Continuous Rating: 500A Intermittent Rating: 700A (5 min) Cranking Rating 30 Seconds: 1450A DC Cable Size to Meet Ratings: 2x (4/0) Live Current Switching: 300A@12VDC Switching Cycles: 100,000 Terminal Ring Diameter Clearance: 1.18" (29.97 mm) Terminal Stud Length: 0.875" (22.23 mm) Terminal Stud Size: 3/8" - 16 (M10)

8080 Single Circuit ON/OFF - Plus Main  Installed Components: 2 6006 m-Series Switches 1 100A c-Series Flat Rocker Circuit Breaker Features: Isolates batteries and provides DC main circuit protection Ignition protected - Safe for installation aboard gasoline powered boats Isolates the Engine circuit from the House circuit Simplifies battery switch operation Protects electronics from sags and spikes caused by engine cranking Discharges batteries independently Addition of an Automatic Charging Relay automates charging of both batteries Enables a failed Start battery to be isolated from the electrical system and both House and Start loads to be operated from the remaining battery bank Provides main circuit protection for DC House power system Enables a failed House or Start battery bank to be isolated from the electrical system and both House and Start loads to be operated from the remaining battery bank Simplifies battery switch operation Isolates Start circuit from House circuit Protects electronics from sags and spikes caused by engine cranking Ignition protected - Safe for installation aboard gasoline-powered boats Addition of an Automatic Charging Relay automates charging both batteries Allows independent battery discharge WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.